lkml.org 
[lkml]   [2014]   [Nov]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH V3] arm64: amd-seattle: Adding device tree for AMD Seattle platform
Date
On Friday 21 November 2014 01:12:45 Suthikulpanit, Suravee wrote:
> On 11/13/14 18:29, Arnd Bergmann wrote:
> > On Tuesday 28 October 2014 08:36:54 suravee.suthikulpanit@amd.com wrote:
> >> From: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
> >>
> >> Initial revision of device tree for AMD Seattle platform
> >
> > Sorry for not looking at this earlier in enough detail.
> >
> >> + dma0: dma@0500000 {
> >> + compatible = "arm,pl330", "arm,primecell";
> >> + reg = <0 0x0500000 0 0x1000>;
> >> + interrupts =
> >> + <0 368 4>,
> >> + <0 369 4>,
> >> + <0 370 4>,
> >> + <0 371 4>,
> >> + <0 372 4>,
> >> + <0 373 4>,
> >> + <0 374 4>,
> >> + <0 375 4>;
> >> + clocks = <&dmaclk_500mhz>;
> >> + clock-names = "apb_pclk";
> >> + #dma-cells = <1>;
> >> + };
> >
> > Is this device cache-coherent?
> >
> > Does it support larger than 32-bit DMA addresses?
>
> The pl330 is only 32-bit DMA addressable, and need to be used with
> the smmu (not yet included here) before it can be used in the system.
> Therefore, it should be cache coherent by the virtue of the SMMU.
>
> I¹ll remove this until the SMMU stuff is tested and ready.

Ok, makes sense.

> >
> >> + sata0: sata@00300000 {
> >> + compatible = "snps,dwc-ahci";
> >> + reg = <0 0x300000 0 0x800>;
> >> + interrupts = <0 355 4>;
> >> + clocks = <&sataclk_333mhz>;
> >> + clock-names = "apb_pclk";
> >> + dma-coherent;
> >> + };
> >
> > Same here: you list it as coherent, but not 64-bit DMA capable.
> > Is that intentional?
>
> Correct me if I am wrong, but I didn't think that we need to specify
> here since the AHCI platform driver determines the DMA bitness by
> checking struct ahci_host_priv.cap for HOST_CAP_64 (see
> drivers/ata/libahci_platform.c).

No, the actual DMA mask that gets used is the combination of what
the device claims to support and what the bus can do. Without the
dma-ranges property, the bus will be seen as 32-bit only, so we won't
allow high DMA transfers for devices that can do it.

This is the same way we have to treat any PCI device as well, since
a lot of PCI devices can do 64-bit DMA, but they can also be connected
to a pci host bridge that sits on a 32-bit bus and has no supported
IOMMU.

> However, based on the conversation on the IRC, I¹ll add the dma-ranges
> in the motherboard level.

Ok.

> >
> >> + i2c@1000000 {
> >> + compatible = "snps,designware-i2c";
> >> + reg = <0 0x01000000 0 0x1000>;
> >> + interrupts = <0 357 4>;
> >> + clocks = <&uartspiclk_100mhz>;
> >> + clock-names = "apb_pclk";
> >> + };
> >> +
> >> + serial0: serial@1010000 {
> >> + compatible = "arm,pl011", "arm,primecell";
> >> + reg = <0 0x1010000 0 0x1000>;
> >> + interrupts = <0 328 4>;
> >> + clocks = <&uartspiclk_100mhz>, <&uartspiclk_100mhz>;
> >> + clock-names = "uartclk", "apb_pclk";
> >> + };
> >> +
> >> + ssp@1020000 {
> >> + compatible = "arm,pl022", "arm,primecell";
> >> + #gpio-cells = <2>;
> >> + reg = <0 0x1020000 0 0x1000>;
> >> + spi-controller;
> >> + interrupts = <0 330 4>;
> >> + clocks = <&uartspiclk_100mhz>;
> >> + clock-names = "apb_pclk";
> >> + };
> >
> > Should these three be connected to the DMA engine?
>
> It doesn't do DMA. Only PCI devices, XGBE, and SATA do DMA.

What is the pl330 connected to then? It's very common for pl011
and pl022 to be used in combination with a pl330 in order to
do DMA.

> >> + pcie0: pcie-controller{
> >> + compatible = "pci-host-ecam-generic";
> >> + #address-cells = <3>;
> >> + #size-cells = <2>;
> >> + device_type = "pci";
> >> + bus-range = <0 0xff>;
> >> + reg = <0 0xf0000000 0 0x10000000>;
> >> + dma-coherent;
> >> + msi-parent = <&v2m0>;
> >
> > This surely needs a dma-ranges property to allow larger than 32-bit DMA.
>
> So, I assume this will also need dma-range handling code to be added to
> the PCI generic host driver.

Yes, good point.


> I will made the changes accordingly.

thanks,

Arnd


\
 
 \ /
  Last update: 2014-11-21 14:21    [W:0.065 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site