lkml.org 
[lkml]   [2014]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] PCI: pciehp: Check link state before accessing device during removal
While removing a card, we can't assume the presence to mean that the
access to card is OK. That is because the cause of removal may be a
link down event, and the card may still be physically present. Thus,
instead of presence, use the link state to decide whether or not it is
OK to access the card devices.

Here are the problem symptoms:
During the removal of a card due to link down, sometimes the following
error is seen (because pciehp_unconfigure_device() reads 0xFF from
bridge control register as the link is down, which cause it to assume
that the VGA bit is set):

pciehp 0000:21:05.0:pcie24: pcie_isr: intr_loc 100
pciehp 0000:21:05.0:pcie24: Data Link Layer State change
pciehp 0000:21:05.0:pcie24: slot(5): Link Down event
pciehp 0000:21:05.0:pcie24: Disabling domain:bus:device=0000:60:00
pciehp 0000:21:05.0:pcie24: pciehp_unconfigure_device: domain:bus:dev = 0000:60:00
pciehp 0000:21:05.0:pcie24: Cannot remove display device 0000:60:00.0

Ofcourse, when the link comes back up, the device addition fails too:

pciehp 0000:21:05.0:pcie24: pcie_isr: intr_loc 100
pciehp 0000:21:05.0:pcie24: Data Link Layer State change
pciehp 0000:21:05.0:pcie24: pciehp_check_link_active: lnk_status = 6011
pciehp 0000:21:05.0:pcie24: slot(5): Link Up event
pciehp 0000:21:05.0:pcie24: Enabling domain:bus:device=0000:60:00
pciehp 0000:21:05.0:pcie24: pciehp_check_link_active: lnk_status = 6011
pciehp 0000:21:05.0:pcie24: pciehp_check_link_status: lnk_status = 6011
pciehp 0000:21:05.0:pcie24: Device 0000:60:00.0 already exists at 0000:60:00, cannot hot-add
pciehp 0000:21:05.0:pcie24: Cannot add device at 0000:60:00

The problem is not seen with this patch applied. The device removal and
insertion works as expected.

Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
---
drivers/pci/hotplug/pciehp_pci.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/hotplug/pciehp_pci.c b/drivers/pci/hotplug/pciehp_pci.c
index 9e69403..8572af6 100644
--- a/drivers/pci/hotplug/pciehp_pci.c
+++ b/drivers/pci/hotplug/pciehp_pci.c
@@ -77,7 +77,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
{
int rc = 0;
u8 bctl = 0;
- u8 presence = 0;
+ bool link_active = false;
struct pci_dev *dev, *temp;
struct pci_bus *parent = p_slot->ctrl->pcie->port->subordinate;
u16 command;
@@ -85,7 +85,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)

ctrl_dbg(ctrl, "%s: domain:bus:dev = %04x:%02x:00\n",
__func__, pci_domain_nr(parent), parent->number);
- pciehp_get_adapter_status(p_slot, &presence);
+ link_active = pciehp_check_link_active(p_slot->ctrl);

pci_lock_rescan_remove();

@@ -98,7 +98,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
list_for_each_entry_safe_reverse(dev, temp, &parent->devices,
bus_list) {
pci_dev_get(dev);
- if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE && presence) {
+ if (dev->hdr_type == PCI_HEADER_TYPE_BRIDGE && link_active) {
pci_read_config_byte(dev, PCI_BRIDGE_CONTROL, &bctl);
if (bctl & PCI_BRIDGE_CTL_VGA) {
ctrl_err(ctrl,
@@ -114,7 +114,7 @@ int pciehp_unconfigure_device(struct slot *p_slot)
* Ensure that no new Requests will be generated from
* the device.
*/
- if (presence) {
+ if (link_active) {
pci_read_config_word(dev, PCI_COMMAND, &command);
command &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_SERR);
command |= PCI_COMMAND_INTX_DISABLE;
--
1.7.9.5


\
 
 \ /
  Last update: 2014-11-21 00:01    [W:0.029 / U:1.620 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site