lkml.org 
[lkml]   [2014]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v8 11/13] ARM: dts: Berlin: enable USB on the BG2Q DMP
On 17.11.2014 14:35, Antoine Tenart wrote:
> Enable the 2 available USB PHY and USB nodes on the Marvell Berlin BG2Q
> DMP.
>
> Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>

Applied to berlin/dt.

Thanks!

> ---
> arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 53 ++++++++++++++++++++++++++++++
> 1 file changed, 53 insertions(+)
>
> diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> index ea1f99b8eed6..f7c25580e122 100644
> --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> @@ -7,6 +7,8 @@
> */
>
> /dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> #include "berlin2q.dtsi"
>
> / {
> @@ -21,6 +23,39 @@
> choosen {
> bootargs = "console=ttyS0,115200 earlyprintk";
> };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_usb0_vbus: regulator@0 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb0_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&portb 8 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb1_vbus: regulator@1 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&portb 10 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_usb2_vbus: regulator@2 {
> + compatible = "regulator-fixed";
> + regulator-name = "usb2_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> + };
> };
>
> &sdhci1 {
> @@ -46,6 +81,24 @@
> status = "okay";
> };
>
> +&usb_phy0 {
> + status = "okay";
> +};
> +
> +&usb_phy2 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + vbus-supply = <&reg_usb0_vbus>;
> + status = "okay";
> +};
> +
> +&usb2 {
> + vbus-supply = <&reg_usb2_vbus>;
> + status = "okay";
> +};
> +
> &eth0 {
> status = "okay";
> };
>



\
 
 \ /
  Last update: 2014-11-18 21:21    [W:0.247 / U:0.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site