Messages in this thread | | | Date | Tue, 18 Nov 2014 20:36:49 +0100 | From | Sebastian Hesselbarth <> | Subject | Re: [PATCH v8 10/13] ARM: dts: berlin: add BG2Q nodes for USB support |
| |
On 17.11.2014 14:35, Antoine Tenart wrote: > Adds nodes describing the Marvell Berlin BG2Q USB PHY and USB. The BG2Q > SoC has 3 USB host controller, compatible with ChipIdea. > > Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Applied to berlin/dt with the whitespace removed that Sergei pointed out.
Thanks!
> --- > arch/arm/boot/dts/berlin2q.dtsi | 55 +++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 55 insertions(+) > > diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi > index 2de8d6f8973c..834142bdfbb1 100644 > --- a/arch/arm/boot/dts/berlin2q.dtsi > +++ b/arch/arm/boot/dts/berlin2q.dtsi > @@ -114,6 +114,40 @@ > #interrupt-cells = <3>; > }; > > + usb_phy2: phy@a2f400 { > + compatible = "marvell,berlin2-usb-phy"; > + reg = <0xa2f400 0x128>; > + #phy-cells = <0>; > + resets = <&chip 0x104 14>; > + status = "disabled"; > + }; > + > + usb2: usb@a30000 { > + compatible = "chipidea,usb2"; > + reg = <0xa30000 0x10000>; > + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&chip CLKID_USB2>; > + phys = <&usb_phy2>; > + phy-names = "usb-phy"; > + status = "disabled"; > + }; > + > + usb_phy0: phy@b74000 { > + compatible = "marvell,berlin2-usb-phy"; > + reg = <0xb74000 0x128>; > + #phy-cells = <0>; > + resets = <&chip 0x104 12>; > + status = "disabled"; > + }; > + > + usb_phy1: phy@b78000 { > + compatible = "marvell,berlin2-usb-phy"; > + reg = <0xb78000 0x128>; > + #phy-cells = <0>; > + resets = <&chip 0x104 13>; > + status = "disabled"; > + }; > + > eth0: ethernet@b90000 { > compatible = "marvell,pxa168-eth"; > reg = <0xb90000 0x10000>; > @@ -365,6 +399,26 @@ > }; > }; > > + usb0: usb@ed0000 { > + compatible = "chipidea,usb2"; > + reg = <0xed0000 0x10000>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&chip CLKID_USB0>; > + phys = <&usb_phy0>; > + phy-names = "usb-phy"; > + status = "disabled"; > + }; > + > + usb1: usb@ee0000 { > + compatible = "chipidea,usb2"; > + reg = <0xee0000 0x10000>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&chip CLKID_USB1>; > + phys = <&usb_phy1>; > + phy-names = "usb-phy"; > + status = "disabled"; > + }; > + > apb@fc0000 { > compatible = "simple-bus"; > #address-cells = <1>; > @@ -457,5 +511,6 @@ > interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; > }; > }; > + > }; > }; >
| |