lkml.org 
[lkml]   [2014]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] mmc: dw_mmc: try pick the exact same voltage as vmmc for vqmmc
Date
SD2.0 cards need vqmmc and vmmc to be the same.
But vqmmc call regulator_set_voltage to set min_uv(2.7v) as far as possible.
So if we set vmmc 3.3V in dt table, we will get error information as follows:

[ 17.785398] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req
50000000Hz, actual 50000000HZ div = 0)
[ 17.795175] mmc1: new high speed SDHC card at address e624
[ 17.801283] mmcblk1: mmc1:e624 SU08G 7.40 GiB
[ 17.816033] mmcblk1: p1
[ 17.839318] mmcblk1: error -110 sending status command, retrying
[ 17.845363] mmcblk1: error -115 sending stop command, original cmd
response 0x900, card status 0x800b00
[ 17.854758] mmcblk1: error -84 transferring data, sector 32, nr 24,
cmd response 0x900, card status 0xb00
[ 17.864328] mmcblk1: retrying using single block read
[ 17.873647] mmcblk1: error -110 sending status command, retrying
[ 17.879660] mmcblk1: error -84 transferring data, sector 44, nr 12,
cmd response 0x900, card status 0x0
[ 17.889051] end_request: I/O error, dev mmcblk1, sector 44
[ 17.895594] Buffer I/O error on device mmcblk1, logical block 5
[ 17.902484] mmcblk1: error -110 sending status command, retrying
[ 17.908498] mmcblk1: error -84 transferring data, sector 50, nr 6,
cmd response 0x900, card status 0x0
[ 17.917802] end_request: I/O error, dev mmcblk1, sector 50
[ 17.924984] Buffer I/O error on device mmcblk1, logical block 6
[ 18.431258] mmc_host mmc1: Timeout sending command (cmd 0x200000 arg
0x0 status 0x80200000)

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
---
drivers/mmc/host/dw_mmc.c | 10 ++++++++--
1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index b4c3044..a8b70b5 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1163,8 +1163,14 @@ static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
*/
uhs = mci_readl(host, UHS_REG);
if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
- min_uv = 2700000;
- max_uv = 3600000;
+ /* try pick the exact same voltage as vmmc for vqmmc */
+ if (!IS_ERR(mmc->supply.vmmc)) {
+ min_uv = regulator_get_voltage(mmc->supply.vmmc);
+ max_uv = min_uv;
+ } else {
+ min_uv = 2700000;
+ max_uv = 3600000;
+ }
uhs &= ~v18;
} else {
min_uv = 1700000;
--
1.8.3.2



\
 
 \ /
  Last update: 2014-11-11 05:41    [W:0.095 / U:3.376 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site