lkml.org 
[lkml]   [2014]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] tty: serial: msm_serial: Use DT aliases
On 11/10/2014 11:42 AM, Stephen Boyd wrote:
> On 11/10/2014 10:54 AM, Kevin Hilman wrote:
>> On Wed, Oct 22, 2014 at 5:33 PM, Stephen Boyd <sboyd@codeaurora.org> wrote:
>>> We rely on probe order of this driver to determine the line number for
>>> the uart port. This makes it impossible to know the line number
>>> when these devices are populated via DT. Use the DT alias
>>> mechanism to assign the line based on the aliases node.
>>>
>>> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
>> FYI... this patch hit linux-next and caused multiple boot failures on
>> qcom platforms[1] as of next-20141110. I'm assuming this is because
>> the corresponding DTS changes have not hit linux-next yet.
>>
>> Kevin
>>
>> [1] http://status.armcloud.us/boot/?qcom
>
> Hmm the intention was to make it optional so that dts changes aren't
> necessary unless you want deterministic numbering. I screwed that up
> badly :/ Thanks for finding this.
>
> Greg, can you also apply this patch or squash it into the bad one?
>
> ----8<-----
>
> From: Stephen Boyd <sboyd@codeaurora.org>
> Subject: [PATCH] tty: serial: msm_serial: Don't required DT aliases
>
> If there isn't a DT alias then of_alias_get_id() will return
> -ENODEV. This will cause the msm_serial driver to fail probe,
> when we want to keep the previous behavior where we generated a
> dynamic line number at probe time. Restore this behavior by
> generating a dynamic id if the line number is still negative
> after checking for an alias or (in the non-DT case) looking at the
> .id field of the platform device.
>
> Reported-by: Kevin Hilman <khilman@kernel.org>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
> ---
> drivers/tty/serial/msm_serial.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
> index 09364dd8cf3a..d1bc6b6cbc70 100644
> --- a/drivers/tty/serial/msm_serial.c
> +++ b/drivers/tty/serial/msm_serial.c
> @@ -1046,14 +1046,14 @@ static int msm_serial_probe(struct platform_device *pdev)
> const struct of_device_id *id;
> int irq, line;
>
> - if (pdev->id == -1)
> - pdev->id = atomic_inc_return(&msm_uart_next_id) - 1;
> -
> if (pdev->dev.of_node)
> line = of_alias_get_id(pdev->dev.of_node, "serial");
> else
> line = pdev->id;
>
> + if (line < 0)
> + line = atomic_inc_return(&msm_uart_next_id) - 1;
> +
> if (unlikely(line < 0 || line >= UART_NR))

Then this original check for "line < 0" can also be removed.


> return -ENXIO;
>
>



\
 
 \ /
  Last update: 2014-11-11 03:21    [W:0.115 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site