lkml.org 
[lkml]   [2014]   [Oct]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] Input: add i2c/smbus driver for elan touchpad
On Mon, Oct 06, 2014 at 10:24:52AM +0100, Mark Rutland wrote:
> On Fri, Oct 03, 2014 at 10:06:51PM +0100, Dmitry Torokhov wrote:
> > [adding devicetree folks...]
> >
> > On Fri, Oct 03, 2014 at 02:03:57PM -0700, Dmitry Torokhov wrote:
> > > diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt
> > > new file mode 100644
> > > index 0000000..0a6ee7d
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt
> > > @@ -0,0 +1,34 @@
> > > +Elantech I2C Touchpad
> > > +
> > > +Required properties:
> > > +- compatible: must be "elan,i2c_touchpad".
>
> s/_/-/ in DT strings and property names plase.
>
> The name seems very generic, and you mention the driver supports a
> variety of touchpads. Please choose a specific device name for the
> compatible string. Other devices can have that as a fallback entry in
> addition to a more specific string.

Duson, what would be a good model/device name here?

>
> > > +- reg: I2C address of the chip.
> > > +- interrupt-parent: a phandle for the gpio controller (see interrupt
> > > + binding[0]).
> > > +- interrupts: (gpio) interrupt to which the chip is connected (see interrupt
> > > + binding[0]).
>
> If this is an interrupt from the PoV of this device, it doesn't matter
> if the other end is connected to a hardwired interrupt controller or a
> gpio. So drop the mention of GPIOs frmom the interrupt properties.
>
> > > +
> > > +Optional properties:
> > > +- wakeup-source: touchpad should be configured as a wakeup source.
>
> s/should be configured as/can be used as/
>
> > > +- pinctrl-names: should be "default" (see pinctrl binding [1]).
> > > +- pinctrl-0: a phandle pointing to the pin settings for the device (see
> > > + pinctrl binding [1]).
> > > +- vcc-supply: a phandle for the regulator supplying 3.3V power.
> > > +
> > > +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> > > +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
> > > +
> > > +Example:
> > > + &i2c1 {
> > > + /* ... */
> > > +
> > > + touchpad@15 {
> > > + compatible = "elan,i2c_touchpad";
> > > + reg = <0x15>;
> > > + interrupt-parent = <&gpio4>;
> > > + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>;
> > > + wakeup-source;
> > > + };
> > > +
> > > + /* ... */
> > > + };
>
> Otherwise this looks ok.

Thanks Mark.

--
Dmitry


\
 
 \ /
  Last update: 2014-10-06 19:01    [W:0.043 / U:0.612 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site