lkml.org 
[lkml]   [2014]   [Oct]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 5/5] tty/serial: Add earlycon support for Spreadtrum serial driver
On Mon, Oct 20, 2014 at 08:27:24AM +0100, Lyra Zhang wrote:
> 2014-10-17 21:03 GMT+08:00 Mark Rutland <mark.rutland@arm.com>:
> > On Fri, Oct 17, 2014 at 10:54:25AM +0100, Chunyan Zhang wrote:
> >> Add serial driver for spreadtrum sharkl platform with earlycon
> >> support at first.
> >>
> >> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> >> ---
> >> drivers/tty/serial/Kconfig | 24 ++++++++++++++
> >> drivers/tty/serial/Makefile | 1 +
> >> drivers/tty/serial/sprd-serial.c | 64 ++++++++++++++++++++++++++++++++++++++
> >> 3 files changed, 89 insertions(+)
> >> create mode 100644 drivers/tty/serial/sprd-serial.c
> >>
> >> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> >> index 26cec64..33b8f90 100644
> >> --- a/drivers/tty/serial/Kconfig
> >> +++ b/drivers/tty/serial/Kconfig
> >> @@ -113,6 +113,30 @@ config SERIAL_SB1250_DUART_CONSOLE
> >>
> >> If unsure, say Y.
> >>
> >> +config SERIAL_SPRD
> >> + tristate "Support for SPRD serial"
> >> + depends on ARM || ARM64
> >> + select SERIAL_CORE
> >> + help
> >> + This enables the driver for the Spreadtrum's serial.
> >> +
> >> +config SERIAL_SPRD_NR
> >> + int "Maximum number of sprd serial ports"
> >> + depends on SERIAL_SPRD
> >> + default "4"
> >
> > This is not used below.
> >
> Ok, I'll remove it in v3.
>
> >> +
> >> +config SERIAL_SPRD_CONSOLE
> >> + bool "SPRD UART console support"
> >> + depends on SERIAL_SPRD=y
> >> + select SERIAL_CORE_CONSOLE
> >> + select SERIAL_EARLYCON
> >> + help
> >> + Support for early debug console using Spreadtrum's serial. This enables
> >> + the console before standard serial driver is probed. This is enabled
> >> + with "earlycon=serial_sprd" on the kernel command line. The console is
> >> + enabled when early_param is processed.
> >
> > There only appears to be an earlycon driver, and not "standard serial
> > driver".
> >
> > What happens after earlycon?
> >
> > Surely there should be a real driver to take ownership of the UART?
> >
> > As far as I can see it won't be possible to boot your platform to a
> > prompt, because earlycon will have gone before that.
> >
> > Thanks,
> > Mark.
> >
>
> We are planed to add standard serial driver after this patch-set is approved.
> In the first patch we contribute to the upstream, I'd like to add
> architecture related code of
> Spreadtrum's Sharkl, and then we will add more functions about Sharkl3
> SoC step by step.

The series is simple enough that the only issues I've noticed are minor.
I'm happy with that.

However, the absence of a real UART driver means that this series alone
is not sufficient to boot your platform to a usable state. Given that
the rest of the series is simply plumbing, I think it would make sense
for that to accompany a full UART driver (or perhaps some other I/O like
ethernet) such that it's possible to interact with the platform.

Thanks,
Mark.


\
 
 \ /
  Last update: 2014-10-20 12:41    [W:0.039 / U:1.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site