lkml.org 
[lkml]   [2014]   [Jan]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH v7] staging/bluetooth: Add hci_h4p driver

Add hci_h4p bluetooth driver to bluetooth-next. This device is used
for example on Nokia N900 cell phone.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Thanks-to: Sebastian Reichel <sre@debian.org>
Thanks-to: Joe Perches <joe@perches.com>

---

Move it to staging, rename header file as Marcel requested. Driver
still needs too many changes to make direct merge easy, yet it is
useful for using Maemo on N900.

I sent it to the lists, but made a mistake in Greg's address. It
received no comments.

diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 3bfdaa8..8d5af7d 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -150,4 +150,6 @@ source "drivers/staging/dgnc/Kconfig"

source "drivers/staging/dgap/Kconfig"

+source "drivers/staging/nokia_h4p/Kconfig"
+
endif # STAGING
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index b0d3303..cb2991e 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -67,3 +67,4 @@ obj-$(CONFIG_XILLYBUS) += xillybus/
obj-$(CONFIG_DGNC) += dgnc/
obj-$(CONFIG_DGAP) += dgap/
obj-$(CONFIG_MTD_SPINAND_MT29F) += mt29f_spinand/
+obj-$(CONFIG_BT_NOKIA_H4P) += nokia_h4p/
diff --git a/drivers/staging/nokia_h4p/Kconfig b/drivers/staging/nokia_h4p/Kconfig
new file mode 100644
index 0000000..4336c0a
--- /dev/null
+++ b/drivers/staging/nokia_h4p/Kconfig
@@ -0,0 +1,9 @@
+config BT_NOKIA_H4P
+ tristate "HCI driver with H4 Nokia extensions"
+ depends on BT && ARCH_OMAP
+ help
+ Bluetooth HCI driver with H4 extensions. This driver provides
+ support for H4+ Bluetooth chip with vendor-specific H4 extensions.
+
+ Say Y here to compile support for h4 extended devices into the kernel
+ or say M to compile it as module (btnokia_h4p).
diff --git a/drivers/staging/nokia_h4p/Makefile b/drivers/staging/nokia_h4p/Makefile
new file mode 100644
index 0000000..9625db4
--- /dev/null
+++ b/drivers/staging/nokia_h4p/Makefile
@@ -0,0 +1,6 @@
+
+obj-$(CONFIG_BT_NOKIA_H4P) += btnokia_h4p.o
+btnokia_h4p-objs := nokia_core.o nokia_fw.o nokia_uart.o nokia_fw-csr.o \
+ nokia_fw-bcm.o nokia_fw-ti1273.o
+
+ccflags-y += -D__CHECK_ENDIAN__
diff --git a/drivers/staging/nokia_h4p/TODO b/drivers/staging/nokia_h4p/TODO
new file mode 100644
index 0000000..2194146
--- /dev/null
+++ b/drivers/staging/nokia_h4p/TODO
@@ -0,0 +1,140 @@
+Few attempts to submission have been made, last review comments were received in
+
+Date: Wed, 15 Jan 2014 19:01:51 -0800
+From: Marcel Holtmann <marcel@holtmann.org>
+Subject: Re: [PATCH v6] Bluetooth: Add hci_h4p driver
+
+Some code refactoring is still needed.
+
+TODO:
+
+> +++ b/drivers/bluetooth/hci_h4p.h
+
+can we please get the naming straight. File names do not start with
+hci_ anymore. We moved away from it since that term is too generic.
+
+> +#define FW_NAME_TI1271_LE "ti1273_le.bin"
+> +#define FW_NAME_TI1271 "ti1273.bin"
+> +#define FW_NAME_BCM2048 "bcmfw.bin"
+> +#define FW_NAME_CSR "bc4fw.bin"
+
+We do these have to be global in a header file. This should be
+confined to the specific firmware part.
+
+> +struct hci_h4p_info {
+
+Can we please get rid of the hci_ prefix for everything. Copying from
+drivers that are over 10 years old is not a good idea. Please look at
+recent ones.
+
+> + struct timer_list lazy_release;
+
+Timer? Not delayed work?
+
+> +void hci_h4p_outb(struct hci_h4p_info *info, unsigned int offset, u8 val);
+> +u8 hci_h4p_inb(struct hci_h4p_info *info, unsigned int offset);
+> +void hci_h4p_set_rts(struct hci_h4p_info *info, int active);
+> +int hci_h4p_wait_for_cts(struct hci_h4p_info *info, int active, int timeout_ms);
+> +void __hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which);
+> +void hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which);
+> +void hci_h4p_change_speed(struct hci_h4p_info *info, unsigned long speed);
+> +int hci_h4p_reset_uart(struct hci_h4p_info *info);
+> +void hci_h4p_init_uart(struct hci_h4p_info *info);
+> +void hci_h4p_enable_tx(struct hci_h4p_info *info);
+> +void hci_h4p_store_regs(struct hci_h4p_info *info);
+> +void hci_h4p_restore_regs(struct hci_h4p_info *info);
+> +void hci_h4p_smart_idle(struct hci_h4p_info *info, bool enable);
+
+These are a lot of public functions. Are they all really needed or can
+the code be done smart.
+
+> +static ssize_t hci_h4p_store_bdaddr(struct device *dev,
+> + struct device_attribute *attr,
+> + const char *buf, size_t count)
+> +{
+> + struct hci_h4p_info *info = dev_get_drvdata(dev);
+
+Since none of these devices can function without having a valid
+address, the way this should work is that we should not register the
+HCI device when probing the platform device.
+
+The HCI device should be registered once a valid address has been
+written into the sysfs file. I do not want to play the tricks with
+bringing up the device without a valid address.
+
+> + hdev->close = hci_h4p_hci_close;
+> + hdev->flush = hci_h4p_hci_flush;
+> + hdev->send = hci_h4p_hci_send_frame;
+
+It needs to use hdev->setup to load the firmware. I assume the
+firmware only needs to be loaded once. That is exactly what
+hdev->setup does. It gets executed once.
+
+> + set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
+
+Is this quirk really needed? Normally only Bluetooth 1.1 and early
+devices qualify for it.
+
+> +static int hci_h4p_bcm_set_bdaddr(struct hci_h4p_info *info, struct sk_buff *skb)
+> +{
+> + int i;
+> + static const u8 nokia_oui[3] = {0x00, 0x1f, 0xdf};
+> + int not_valid;
+
+Has this actually been confirmed that we can just randomly set an
+address out of the Nokia range. I do not think so. This is a pretty
+bad idea.
+
+I have no interest in merging a driver with such a hack.
+
+> + not_valid = 1;
+> + for (i = 0; i < 6; i++) {
+> + if (info->bd_addr[i] != 0x00) {
+> + not_valid = 0;
+> + break;
+> + }
+> + }
+
+Anybody every heard of memcmp or bacmp and BDADDR_ANY?
+
+> + if (not_valid) {
+> + dev_info(info->dev, "Valid bluetooth address not found,"
+> + " setting some random\n");
+> + /* When address is not valid, use some random */
+> + memcpy(info->bd_addr, nokia_oui, 3);
+> + get_random_bytes(info->bd_addr + 3, 3);
+> + }
+
+
+And why does every single chip firmware does this differently. Seriously, this is a mess.
+
+> +void hci_h4p_parse_fw_event(struct hci_h4p_info *info, struct sk_buff *skb)
+> +{
+> + switch (info->man_id) {
+> + case H4P_ID_CSR:
+> + hci_h4p_bc4_parse_fw_event(info, skb);
+> + break;
+...
+> +}
+
+We have proper HCI sync command handling in recent kernels. I really
+do not know why this is hand coded these days. Check how the Intel
+firmware loading inside btusb.c does it.
+
+> +inline u8 hci_h4p_inb(struct hci_h4p_info *info, unsigned int offset)
+> +{
+> + return __raw_readb(info->uart_base + (offset << 2));
+> +}
+
+Inline in a *.c file for a non-static function. Makes no sense to me.
+
+> +/**
+> + * struct hci_h4p_platform data - hci_h4p Platform data structure
+> + */
+> +struct hci_h4p_platform_data {
+
+please have a proper name here. For example
+btnokia_h4p_platform_data.
+
+Please send patches to Greg Kroah-Hartman <greg@kroah.com> and Cc:
+Pavel Machek <pavel@ucw.cz>
diff --git a/drivers/staging/nokia_h4p/hci_h4p.h b/drivers/staging/nokia_h4p/hci_h4p.h
new file mode 100644
index 0000000..fd7a640
--- /dev/null
+++ b/drivers/staging/nokia_h4p/hci_h4p.h
@@ -0,0 +1,228 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2005-2008 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __DRIVERS_BLUETOOTH_HCI_H4P_H
+#define __DRIVERS_BLUETOOTH_HCI_H4P_H
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+#include <net/bluetooth/hci.h>
+
+#define FW_NAME_TI1271_PRELE "ti1273_prele.bin"
+#define FW_NAME_TI1271_LE "ti1273_le.bin"
+#define FW_NAME_TI1271 "ti1273.bin"
+#define FW_NAME_BCM2048 "bcmfw.bin"
+#define FW_NAME_CSR "bc4fw.bin"
+
+#define UART_SYSC_OMAP_RESET 0x03
+#define UART_SYSS_RESETDONE 0x01
+#define UART_OMAP_SCR_EMPTY_THR 0x08
+#define UART_OMAP_SCR_WAKEUP 0x10
+#define UART_OMAP_SSR_WAKEUP 0x02
+#define UART_OMAP_SSR_TXFULL 0x01
+
+#define UART_OMAP_SYSC_IDLEMODE 0x03
+#define UART_OMAP_SYSC_IDLEMASK (3 << UART_OMAP_SYSC_IDLEMODE)
+
+#define UART_OMAP_SYSC_FORCE_IDLE (0 << UART_OMAP_SYSC_IDLEMODE)
+#define UART_OMAP_SYSC_NO_IDLE (1 << UART_OMAP_SYSC_IDLEMODE)
+#define UART_OMAP_SYSC_SMART_IDLE (2 << UART_OMAP_SYSC_IDLEMODE)
+
+#define H4P_TRANSFER_MODE 1
+#define H4P_SCHED_TRANSFER_MODE 2
+#define H4P_ACTIVE_MODE 3
+
+struct hci_h4p_info {
+ struct timer_list lazy_release;
+ struct hci_dev *hdev;
+ spinlock_t lock;
+
+ void __iomem *uart_base;
+ unsigned long uart_phys_base;
+ int irq;
+ struct device *dev;
+ u8 chip_type;
+ u8 bt_wakeup_gpio;
+ u8 host_wakeup_gpio;
+ u8 reset_gpio;
+ u8 reset_gpio_shared;
+ u8 bt_sysclk;
+ u8 man_id;
+ u8 ver_id;
+
+ struct sk_buff_head fw_queue;
+ struct sk_buff *alive_cmd_skb;
+ struct completion init_completion;
+ struct completion fw_completion;
+ struct completion test_completion;
+ int fw_error;
+ int init_error;
+
+ struct sk_buff_head txq;
+
+ struct sk_buff *rx_skb;
+ long rx_count;
+ unsigned long rx_state;
+ unsigned long garbage_bytes;
+
+ u8 bd_addr[6];
+ struct sk_buff_head *fw_q;
+
+ int pm_enabled;
+ int tx_enabled;
+ int autorts;
+ int rx_enabled;
+ unsigned long pm_flags;
+
+ int tx_clocks_en;
+ int rx_clocks_en;
+ spinlock_t clocks_lock;
+ struct clk *uart_iclk;
+ struct clk *uart_fclk;
+ atomic_t clk_users;
+ u16 dll;
+ u16 dlh;
+ u16 ier;
+ u16 mdr1;
+ u16 efr;
+};
+
+struct hci_h4p_radio_hdr {
+ __u8 evt;
+ __u8 dlen;
+} __attribute__ ((packed));
+
+struct hci_h4p_neg_hdr {
+ __u8 dlen;
+} __attribute__ ((packed));
+#define H4P_NEG_HDR_SIZE 1
+
+#define H4P_NEG_REQ 0x00
+#define H4P_NEG_ACK 0x20
+#define H4P_NEG_NAK 0x40
+
+#define H4P_PROTO_PKT 0x44
+#define H4P_PROTO_BYTE 0x4c
+
+#define H4P_ID_CSR 0x02
+#define H4P_ID_BCM2048 0x04
+#define H4P_ID_TI1271 0x31
+
+struct hci_h4p_neg_cmd {
+ __u8 ack;
+ __u16 baud;
+ __u16 unused1;
+ __u8 proto;
+ __u16 sys_clk;
+ __u16 unused2;
+} __attribute__ ((packed));
+
+struct hci_h4p_neg_evt {
+ __u8 ack;
+ __u16 baud;
+ __u16 unused1;
+ __u8 proto;
+ __u16 sys_clk;
+ __u16 unused2;
+ __u8 man_id;
+ __u8 ver_id;
+} __attribute__ ((packed));
+
+#define H4P_ALIVE_REQ 0x55
+#define H4P_ALIVE_RESP 0xcc
+
+struct hci_h4p_alive_hdr {
+ __u8 dlen;
+} __attribute__ ((packed));
+#define H4P_ALIVE_HDR_SIZE 1
+
+struct hci_h4p_alive_pkt {
+ __u8 mid;
+ __u8 unused;
+} __attribute__ ((packed));
+
+#define MAX_BAUD_RATE 921600
+#define BC4_MAX_BAUD_RATE 3692300
+#define UART_CLOCK 48000000
+#define BT_INIT_DIVIDER 320
+#define BT_BAUDRATE_DIVIDER 384000000
+#define BT_SYSCLK_DIV 1000
+#define INIT_SPEED 120000
+
+#define H4_TYPE_SIZE 1
+#define H4_RADIO_HDR_SIZE 2
+
+/* H4+ packet types */
+#define H4_CMD_PKT 0x01
+#define H4_ACL_PKT 0x02
+#define H4_SCO_PKT 0x03
+#define H4_EVT_PKT 0x04
+#define H4_NEG_PKT 0x06
+#define H4_ALIVE_PKT 0x07
+#define H4_RADIO_PKT 0x08
+
+/* TX states */
+#define WAIT_FOR_PKT_TYPE 1
+#define WAIT_FOR_HEADER 2
+#define WAIT_FOR_DATA 3
+
+struct hci_fw_event {
+ struct hci_event_hdr hev;
+ struct hci_ev_cmd_complete cmd;
+ u8 status;
+} __attribute__ ((packed));
+
+int hci_h4p_send_alive_packet(struct hci_h4p_info *info);
+
+void hci_h4p_bcm_parse_fw_event(struct hci_h4p_info *info,
+ struct sk_buff *skb);
+int hci_h4p_bcm_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue);
+
+void hci_h4p_bc4_parse_fw_event(struct hci_h4p_info *info,
+ struct sk_buff *skb);
+int hci_h4p_bc4_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue);
+
+void hci_h4p_ti1273_parse_fw_event(struct hci_h4p_info *info,
+ struct sk_buff *skb);
+int hci_h4p_ti1273_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue);
+
+int hci_h4p_read_fw(struct hci_h4p_info *info, struct sk_buff_head *fw_queue);
+int hci_h4p_send_fw(struct hci_h4p_info *info, struct sk_buff_head *fw_queue);
+void hci_h4p_parse_fw_event(struct hci_h4p_info *info, struct sk_buff *skb);
+
+void hci_h4p_outb(struct hci_h4p_info *info, unsigned int offset, u8 val);
+u8 hci_h4p_inb(struct hci_h4p_info *info, unsigned int offset);
+void hci_h4p_set_rts(struct hci_h4p_info *info, int active);
+int hci_h4p_wait_for_cts(struct hci_h4p_info *info, int active, int timeout_ms);
+void __hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which);
+void hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which);
+void hci_h4p_change_speed(struct hci_h4p_info *info, unsigned long speed);
+int hci_h4p_reset_uart(struct hci_h4p_info *info);
+void hci_h4p_init_uart(struct hci_h4p_info *info);
+void hci_h4p_enable_tx(struct hci_h4p_info *info);
+void hci_h4p_store_regs(struct hci_h4p_info *info);
+void hci_h4p_restore_regs(struct hci_h4p_info *info);
+void hci_h4p_smart_idle(struct hci_h4p_info *info, bool enable);
+
+#endif /* __DRIVERS_BLUETOOTH_HCI_H4P_H */
diff --git a/drivers/staging/nokia_h4p/nokia_core.c b/drivers/staging/nokia_h4p/nokia_core.c
new file mode 100644
index 0000000..5da84b0
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_core.c
@@ -0,0 +1,1205 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2005-2008 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ * Thanks to all the Nokia people that helped with this driver,
+ * including Ville Tervo and Roger Quadros.
+ *
+ * Power saving functionality was removed from this driver to make
+ * merging easier.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/serial_reg.h>
+#include <linux/skbuff.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/timer.h>
+#include <linux/kthread.h>
+#include <linux/io.h>
+#include <linux/completion.h>
+#include <linux/sizes.h>
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+#include <net/bluetooth/hci.h>
+
+#include <linux/platform_data/bt-nokia-h4p.h>
+
+#include "hci_h4p.h"
+
+/* This should be used in function that cannot release clocks */
+static void hci_h4p_set_clk(struct hci_h4p_info *info, int *clock, int enable)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->clocks_lock, flags);
+ if (enable && !*clock) {
+ BT_DBG("Enabling %p", clock);
+ clk_prepare_enable(info->uart_fclk);
+ clk_prepare_enable(info->uart_iclk);
+ if (atomic_read(&info->clk_users) == 0)
+ hci_h4p_restore_regs(info);
+ atomic_inc(&info->clk_users);
+ }
+
+ if (!enable && *clock) {
+ BT_DBG("Disabling %p", clock);
+ if (atomic_dec_and_test(&info->clk_users))
+ hci_h4p_store_regs(info);
+ clk_disable_unprepare(info->uart_fclk);
+ clk_disable_unprepare(info->uart_iclk);
+ }
+
+ *clock = enable;
+ spin_unlock_irqrestore(&info->clocks_lock, flags);
+}
+
+static void hci_h4p_lazy_clock_release(unsigned long data)
+{
+ struct hci_h4p_info *info = (struct hci_h4p_info *)data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->lock, flags);
+ if (!info->tx_enabled)
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 0);
+ spin_unlock_irqrestore(&info->lock, flags);
+}
+
+/* Power management functions */
+void hci_h4p_smart_idle(struct hci_h4p_info *info, bool enable)
+{
+ u8 v;
+
+ v = hci_h4p_inb(info, UART_OMAP_SYSC);
+ v &= ~(UART_OMAP_SYSC_IDLEMASK);
+
+ if (enable)
+ v |= UART_OMAP_SYSC_SMART_IDLE;
+ else
+ v |= UART_OMAP_SYSC_NO_IDLE;
+
+ hci_h4p_outb(info, UART_OMAP_SYSC, v);
+}
+
+static inline void h4p_schedule_pm(struct hci_h4p_info *info)
+{
+}
+
+static void hci_h4p_disable_tx(struct hci_h4p_info *info)
+{
+ if (!info->pm_enabled)
+ return;
+
+ /* Re-enable smart-idle */
+ hci_h4p_smart_idle(info, 1);
+
+ gpio_set_value(info->bt_wakeup_gpio, 0);
+ mod_timer(&info->lazy_release, jiffies + msecs_to_jiffies(100));
+ info->tx_enabled = 0;
+}
+
+void hci_h4p_enable_tx(struct hci_h4p_info *info)
+{
+ unsigned long flags;
+
+ if (!info->pm_enabled)
+ return;
+
+ h4p_schedule_pm(info);
+
+ spin_lock_irqsave(&info->lock, flags);
+ del_timer(&info->lazy_release);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 1);
+ info->tx_enabled = 1;
+ gpio_set_value(info->bt_wakeup_gpio, 1);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ /*
+ * Disable smart-idle as UART TX interrupts
+ * are not wake-up capable
+ */
+ hci_h4p_smart_idle(info, 0);
+
+ spin_unlock_irqrestore(&info->lock, flags);
+}
+
+static void hci_h4p_disable_rx(struct hci_h4p_info *info)
+{
+ if (!info->pm_enabled)
+ return;
+
+ info->rx_enabled = 0;
+
+ if (hci_h4p_inb(info, UART_LSR) & UART_LSR_DR)
+ return;
+
+ if (!(hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT))
+ return;
+
+ __hci_h4p_set_auto_ctsrts(info, 0, UART_EFR_RTS);
+ info->autorts = 0;
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 0);
+}
+
+static void hci_h4p_enable_rx(struct hci_h4p_info *info)
+{
+ if (!info->pm_enabled)
+ return;
+
+ h4p_schedule_pm(info);
+
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 1);
+ info->rx_enabled = 1;
+
+ if (!(hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT))
+ return;
+
+ __hci_h4p_set_auto_ctsrts(info, 1, UART_EFR_RTS);
+ info->autorts = 1;
+}
+
+/* Negotiation functions */
+int hci_h4p_send_alive_packet(struct hci_h4p_info *info)
+{
+ struct hci_h4p_alive_hdr *hdr;
+ struct hci_h4p_alive_pkt *pkt;
+ struct sk_buff *skb;
+ unsigned long flags;
+ int len;
+
+ BT_DBG("Sending alive packet");
+
+ len = H4_TYPE_SIZE + sizeof(*hdr) + sizeof(*pkt);
+ skb = bt_skb_alloc(len, GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
+
+ memset(skb->data, 0x00, len);
+ *skb_put(skb, 1) = H4_ALIVE_PKT;
+ hdr = (struct hci_h4p_alive_hdr *)skb_put(skb, sizeof(*hdr));
+ hdr->dlen = sizeof(*pkt);
+ pkt = (struct hci_h4p_alive_pkt *)skb_put(skb, sizeof(*pkt));
+ pkt->mid = H4P_ALIVE_REQ;
+
+ skb_queue_tail(&info->txq, skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ BT_DBG("Alive packet sent");
+
+ return 0;
+}
+
+static void hci_h4p_alive_packet(struct hci_h4p_info *info,
+ struct sk_buff *skb)
+{
+ struct hci_h4p_alive_hdr *hdr;
+ struct hci_h4p_alive_pkt *pkt;
+
+ BT_DBG("Received alive packet");
+ hdr = (struct hci_h4p_alive_hdr *)skb->data;
+ if (hdr->dlen != sizeof(*pkt)) {
+ dev_err(info->dev, "Corrupted alive message\n");
+ info->init_error = -EIO;
+ goto finish_alive;
+ }
+
+ pkt = (struct hci_h4p_alive_pkt *)skb_pull(skb, sizeof(*hdr));
+ if (pkt->mid != H4P_ALIVE_RESP) {
+ dev_err(info->dev, "Could not negotiate hci_h4p settings\n");
+ info->init_error = -EINVAL;
+ }
+
+finish_alive:
+ complete(&info->init_completion);
+ kfree_skb(skb);
+}
+
+static int hci_h4p_send_negotiation(struct hci_h4p_info *info)
+{
+ struct hci_h4p_neg_cmd *neg_cmd;
+ struct hci_h4p_neg_hdr *neg_hdr;
+ struct sk_buff *skb;
+ unsigned long flags;
+ int err, len;
+ u16 sysclk;
+
+ BT_DBG("Sending negotiation..");
+
+ switch (info->bt_sysclk) {
+ case 1:
+ sysclk = 12000;
+ break;
+ case 2:
+ sysclk = 38400;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ len = sizeof(*neg_cmd) + sizeof(*neg_hdr) + H4_TYPE_SIZE;
+ skb = bt_skb_alloc(len, GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
+
+ memset(skb->data, 0x00, len);
+ *skb_put(skb, 1) = H4_NEG_PKT;
+ neg_hdr = (struct hci_h4p_neg_hdr *)skb_put(skb, sizeof(*neg_hdr));
+ neg_cmd = (struct hci_h4p_neg_cmd *)skb_put(skb, sizeof(*neg_cmd));
+
+ neg_hdr->dlen = sizeof(*neg_cmd);
+ neg_cmd->ack = H4P_NEG_REQ;
+ neg_cmd->baud = cpu_to_le16(BT_BAUDRATE_DIVIDER/MAX_BAUD_RATE);
+ neg_cmd->proto = H4P_PROTO_BYTE;
+ neg_cmd->sys_clk = cpu_to_le16(sysclk);
+
+ hci_h4p_change_speed(info, INIT_SPEED);
+
+ hci_h4p_set_rts(info, 1);
+ info->init_error = 0;
+ init_completion(&info->init_completion);
+ skb_queue_tail(&info->txq, skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ if (!wait_for_completion_interruptible_timeout(&info->init_completion,
+ msecs_to_jiffies(1000)))
+ return -ETIMEDOUT;
+
+ if (info->init_error < 0)
+ return info->init_error;
+
+ /* Change to operational settings */
+ hci_h4p_set_auto_ctsrts(info, 0, UART_EFR_RTS);
+ hci_h4p_set_rts(info, 0);
+ hci_h4p_change_speed(info, MAX_BAUD_RATE);
+
+ err = hci_h4p_wait_for_cts(info, 1, 100);
+ if (err < 0)
+ return err;
+
+ hci_h4p_set_auto_ctsrts(info, 1, UART_EFR_RTS);
+ init_completion(&info->init_completion);
+ err = hci_h4p_send_alive_packet(info);
+
+ if (err < 0)
+ return err;
+
+ if (!wait_for_completion_interruptible_timeout(&info->init_completion,
+ msecs_to_jiffies(1000)))
+ return -ETIMEDOUT;
+
+ if (info->init_error < 0)
+ return info->init_error;
+
+ BT_DBG("Negotiation successful");
+ return 0;
+}
+
+static void hci_h4p_negotiation_packet(struct hci_h4p_info *info,
+ struct sk_buff *skb)
+{
+ struct hci_h4p_neg_hdr *hdr;
+ struct hci_h4p_neg_evt *evt;
+
+ hdr = (struct hci_h4p_neg_hdr *)skb->data;
+ if (hdr->dlen != sizeof(*evt)) {
+ info->init_error = -EIO;
+ goto finish_neg;
+ }
+
+ evt = (struct hci_h4p_neg_evt *)skb_pull(skb, sizeof(*hdr));
+
+ if (evt->ack != H4P_NEG_ACK) {
+ dev_err(info->dev, "Could not negotiate hci_h4p settings\n");
+ info->init_error = -EINVAL;
+ }
+
+ info->man_id = evt->man_id;
+ info->ver_id = evt->ver_id;
+
+finish_neg:
+
+ complete(&info->init_completion);
+ kfree_skb(skb);
+}
+
+/* H4 packet handling functions */
+static int hci_h4p_get_hdr_len(struct hci_h4p_info *info, u8 pkt_type)
+{
+ long retval;
+
+ switch (pkt_type) {
+ case H4_EVT_PKT:
+ retval = HCI_EVENT_HDR_SIZE;
+ break;
+ case H4_ACL_PKT:
+ retval = HCI_ACL_HDR_SIZE;
+ break;
+ case H4_SCO_PKT:
+ retval = HCI_SCO_HDR_SIZE;
+ break;
+ case H4_NEG_PKT:
+ retval = H4P_NEG_HDR_SIZE;
+ break;
+ case H4_ALIVE_PKT:
+ retval = H4P_ALIVE_HDR_SIZE;
+ break;
+ case H4_RADIO_PKT:
+ retval = H4_RADIO_HDR_SIZE;
+ break;
+ default:
+ dev_err(info->dev, "Unknown H4 packet type 0x%.2x\n", pkt_type);
+ retval = -1;
+ break;
+ }
+
+ return retval;
+}
+
+static unsigned int hci_h4p_get_data_len(struct hci_h4p_info *info,
+ struct sk_buff *skb)
+{
+ long retval = -1;
+ struct hci_acl_hdr *acl_hdr;
+ struct hci_sco_hdr *sco_hdr;
+ struct hci_event_hdr *evt_hdr;
+ struct hci_h4p_neg_hdr *neg_hdr;
+ struct hci_h4p_alive_hdr *alive_hdr;
+ struct hci_h4p_radio_hdr *radio_hdr;
+
+ switch (bt_cb(skb)->pkt_type) {
+ case H4_EVT_PKT:
+ evt_hdr = (struct hci_event_hdr *)skb->data;
+ retval = evt_hdr->plen;
+ break;
+ case H4_ACL_PKT:
+ acl_hdr = (struct hci_acl_hdr *)skb->data;
+ retval = le16_to_cpu(acl_hdr->dlen);
+ break;
+ case H4_SCO_PKT:
+ sco_hdr = (struct hci_sco_hdr *)skb->data;
+ retval = sco_hdr->dlen;
+ break;
+ case H4_RADIO_PKT:
+ radio_hdr = (struct hci_h4p_radio_hdr *)skb->data;
+ retval = radio_hdr->dlen;
+ break;
+ case H4_NEG_PKT:
+ neg_hdr = (struct hci_h4p_neg_hdr *)skb->data;
+ retval = neg_hdr->dlen;
+ break;
+ case H4_ALIVE_PKT:
+ alive_hdr = (struct hci_h4p_alive_hdr *)skb->data;
+ retval = alive_hdr->dlen;
+ break;
+ }
+
+ return retval;
+}
+
+static inline void hci_h4p_recv_frame(struct hci_h4p_info *info,
+ struct sk_buff *skb)
+{
+ if (unlikely(!test_bit(HCI_RUNNING, &info->hdev->flags))) {
+ switch (bt_cb(skb)->pkt_type) {
+ case H4_NEG_PKT:
+ hci_h4p_negotiation_packet(info, skb);
+ info->rx_state = WAIT_FOR_PKT_TYPE;
+ return;
+ case H4_ALIVE_PKT:
+ hci_h4p_alive_packet(info, skb);
+ info->rx_state = WAIT_FOR_PKT_TYPE;
+ return;
+ }
+
+ if (!test_bit(HCI_UP, &info->hdev->flags)) {
+ BT_DBG("fw_event");
+ hci_h4p_parse_fw_event(info, skb);
+ return;
+ }
+ }
+
+ hci_recv_frame(info->hdev, skb);
+ BT_DBG("Frame sent to upper layer");
+}
+
+static inline void hci_h4p_handle_byte(struct hci_h4p_info *info, u8 byte)
+{
+ switch (info->rx_state) {
+ case WAIT_FOR_PKT_TYPE:
+ bt_cb(info->rx_skb)->pkt_type = byte;
+ info->rx_count = hci_h4p_get_hdr_len(info, byte);
+ if (info->rx_count < 0) {
+ info->hdev->stat.err_rx++;
+ kfree_skb(info->rx_skb);
+ info->rx_skb = NULL;
+ } else {
+ info->rx_state = WAIT_FOR_HEADER;
+ }
+ break;
+ case WAIT_FOR_HEADER:
+ info->rx_count--;
+ *skb_put(info->rx_skb, 1) = byte;
+ if (info->rx_count != 0)
+ break;
+ info->rx_count = hci_h4p_get_data_len(info, info->rx_skb);
+ if (info->rx_count > skb_tailroom(info->rx_skb)) {
+ dev_err(info->dev, "frame too long\n");
+ info->garbage_bytes = info->rx_count
+ - skb_tailroom(info->rx_skb);
+ kfree_skb(info->rx_skb);
+ info->rx_skb = NULL;
+ break;
+ }
+ info->rx_state = WAIT_FOR_DATA;
+ break;
+ case WAIT_FOR_DATA:
+ info->rx_count--;
+ *skb_put(info->rx_skb, 1) = byte;
+ break;
+ default:
+ WARN_ON(1);
+ break;
+ }
+
+ if (info->rx_count == 0) {
+ /* H4+ devices should always send word aligned packets */
+ if (!(info->rx_skb->len % 2))
+ info->garbage_bytes++;
+ hci_h4p_recv_frame(info, info->rx_skb);
+ info->rx_skb = NULL;
+ }
+}
+
+static void hci_h4p_rx_tasklet(unsigned long data)
+{
+ u8 byte;
+ struct hci_h4p_info *info = (struct hci_h4p_info *)data;
+
+ BT_DBG("tasklet woke up");
+ BT_DBG("rx_tasklet woke up");
+
+ while (hci_h4p_inb(info, UART_LSR) & UART_LSR_DR) {
+ byte = hci_h4p_inb(info, UART_RX);
+ if (info->garbage_bytes) {
+ info->garbage_bytes--;
+ continue;
+ }
+ if (info->rx_skb == NULL) {
+ info->rx_skb = bt_skb_alloc(HCI_MAX_FRAME_SIZE,
+ GFP_ATOMIC | GFP_DMA);
+ if (!info->rx_skb) {
+ dev_err(info->dev,
+ "No memory for new packet\n");
+ goto finish_rx;
+ }
+ info->rx_state = WAIT_FOR_PKT_TYPE;
+ info->rx_skb->dev = (void *)info->hdev;
+ }
+ info->hdev->stat.byte_rx++;
+ hci_h4p_handle_byte(info, byte);
+ }
+
+ if (!info->rx_enabled) {
+ if (hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT &&
+ info->autorts) {
+ __hci_h4p_set_auto_ctsrts(info, 0 , UART_EFR_RTS);
+ info->autorts = 0;
+ }
+ /* Flush posted write to avoid spurious interrupts */
+ hci_h4p_inb(info, UART_OMAP_SCR);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 0);
+ }
+
+finish_rx:
+ BT_DBG("rx_ended");
+}
+
+static void hci_h4p_tx_tasklet(unsigned long data)
+{
+ unsigned int sent = 0;
+ struct sk_buff *skb;
+ struct hci_h4p_info *info = (struct hci_h4p_info *)data;
+
+ BT_DBG("tasklet woke up");
+ BT_DBG("tx_tasklet woke up");
+
+ if (info->autorts != info->rx_enabled) {
+ if (hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT) {
+ if (info->autorts && !info->rx_enabled) {
+ __hci_h4p_set_auto_ctsrts(info, 0,
+ UART_EFR_RTS);
+ info->autorts = 0;
+ }
+ if (!info->autorts && info->rx_enabled) {
+ __hci_h4p_set_auto_ctsrts(info, 1,
+ UART_EFR_RTS);
+ info->autorts = 1;
+ }
+ } else {
+ hci_h4p_outb(info, UART_OMAP_SCR,
+ hci_h4p_inb(info, UART_OMAP_SCR) |
+ UART_OMAP_SCR_EMPTY_THR);
+ goto finish_tx;
+ }
+ }
+
+ skb = skb_dequeue(&info->txq);
+ if (!skb) {
+ /* No data in buffer */
+ BT_DBG("skb ready");
+ if (hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT) {
+ hci_h4p_outb(info, UART_IER,
+ hci_h4p_inb(info, UART_IER) &
+ ~UART_IER_THRI);
+ hci_h4p_inb(info, UART_OMAP_SCR);
+ hci_h4p_disable_tx(info);
+ return;
+ }
+ hci_h4p_outb(info, UART_OMAP_SCR,
+ hci_h4p_inb(info, UART_OMAP_SCR) |
+ UART_OMAP_SCR_EMPTY_THR);
+ goto finish_tx;
+ }
+
+ /* Copy data to tx fifo */
+ while (!(hci_h4p_inb(info, UART_OMAP_SSR) & UART_OMAP_SSR_TXFULL) &&
+ (sent < skb->len)) {
+ hci_h4p_outb(info, UART_TX, skb->data[sent]);
+ sent++;
+ }
+
+ info->hdev->stat.byte_tx += sent;
+ if (skb->len == sent) {
+ kfree_skb(skb);
+ } else {
+ skb_pull(skb, sent);
+ skb_queue_head(&info->txq, skb);
+ }
+
+ hci_h4p_outb(info, UART_OMAP_SCR, hci_h4p_inb(info, UART_OMAP_SCR) &
+ ~UART_OMAP_SCR_EMPTY_THR);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+
+finish_tx:
+ /* Flush posted write to avoid spurious interrupts */
+ hci_h4p_inb(info, UART_OMAP_SCR);
+
+}
+
+static irqreturn_t hci_h4p_interrupt(int irq, void *data)
+{
+ struct hci_h4p_info *info = (struct hci_h4p_info *)data;
+ u8 iir, msr;
+ int ret;
+
+ ret = IRQ_NONE;
+
+ iir = hci_h4p_inb(info, UART_IIR);
+ if (iir & UART_IIR_NO_INT)
+ return IRQ_HANDLED;
+
+ BT_DBG("In interrupt handler iir 0x%.2x", iir);
+
+ iir &= UART_IIR_ID;
+
+ if (iir == UART_IIR_MSI) {
+ msr = hci_h4p_inb(info, UART_MSR);
+ ret = IRQ_HANDLED;
+ }
+ if (iir == UART_IIR_RLSI) {
+ hci_h4p_inb(info, UART_RX);
+ hci_h4p_inb(info, UART_LSR);
+ ret = IRQ_HANDLED;
+ }
+
+ if (iir == UART_IIR_RDI) {
+ hci_h4p_rx_tasklet((unsigned long)data);
+ ret = IRQ_HANDLED;
+ }
+
+ if (iir == UART_IIR_THRI) {
+ hci_h4p_tx_tasklet((unsigned long)data);
+ ret = IRQ_HANDLED;
+ }
+
+ return ret;
+}
+
+static irqreturn_t hci_h4p_wakeup_interrupt(int irq, void *dev_inst)
+{
+ struct hci_h4p_info *info = dev_inst;
+ int should_wakeup;
+ struct hci_dev *hdev;
+
+ if (!info->hdev)
+ return IRQ_HANDLED;
+
+ should_wakeup = gpio_get_value(info->host_wakeup_gpio);
+ hdev = info->hdev;
+
+ if (!test_bit(HCI_RUNNING, &hdev->flags)) {
+ if (should_wakeup == 1)
+ complete_all(&info->test_completion);
+
+ return IRQ_HANDLED;
+ }
+
+ BT_DBG("gpio interrupt %d", should_wakeup);
+
+ /* Check if wee have missed some interrupts */
+ if (info->rx_enabled == should_wakeup)
+ return IRQ_HANDLED;
+
+ if (should_wakeup)
+ hci_h4p_enable_rx(info);
+ else
+ hci_h4p_disable_rx(info);
+
+ return IRQ_HANDLED;
+}
+
+static inline void hci_h4p_set_pm_limits(struct hci_h4p_info *info, bool set)
+{
+ struct hci_h4p_platform_data *bt_plat_data = info->dev->platform_data;
+ const char *sset = set ? "set" : "clear";
+
+ if (unlikely(!bt_plat_data || !bt_plat_data->set_pm_limits))
+ return;
+
+ if (set != !!test_bit(H4P_ACTIVE_MODE, &info->pm_flags)) {
+ bt_plat_data->set_pm_limits(info->dev, set);
+ if (set)
+ set_bit(H4P_ACTIVE_MODE, &info->pm_flags);
+ else
+ clear_bit(H4P_ACTIVE_MODE, &info->pm_flags);
+ BT_DBG("Change pm constraints to: %s", sset);
+ return;
+ }
+
+ BT_DBG("pm constraints remains: %s", sset);
+}
+
+static int hci_h4p_reset(struct hci_h4p_info *info)
+{
+ int err;
+
+ err = hci_h4p_reset_uart(info);
+ if (err < 0) {
+ dev_err(info->dev, "Uart reset failed\n");
+ return err;
+ }
+ hci_h4p_init_uart(info);
+ hci_h4p_set_rts(info, 0);
+
+ gpio_set_value(info->reset_gpio, 0);
+ gpio_set_value(info->bt_wakeup_gpio, 1);
+ msleep(10);
+
+ if (gpio_get_value(info->host_wakeup_gpio) == 1) {
+ dev_err(info->dev, "host_wakeup_gpio not low\n");
+ return -EPROTO;
+ }
+
+ init_completion(&info->test_completion);
+ gpio_set_value(info->reset_gpio, 1);
+
+ if (!wait_for_completion_interruptible_timeout(&info->test_completion,
+ msecs_to_jiffies(100))) {
+ dev_err(info->dev, "wakeup test timed out\n");
+ complete_all(&info->test_completion);
+ return -EPROTO;
+ }
+
+ err = hci_h4p_wait_for_cts(info, 1, 100);
+ if (err < 0) {
+ dev_err(info->dev, "No cts from bt chip\n");
+ return err;
+ }
+
+ hci_h4p_set_rts(info, 1);
+
+ return 0;
+}
+
+/* hci callback functions */
+static int hci_h4p_hci_flush(struct hci_dev *hdev)
+{
+ struct hci_h4p_info *info = hci_get_drvdata(hdev);
+ skb_queue_purge(&info->txq);
+
+ return 0;
+}
+
+static int hci_h4p_bt_wakeup_test(struct hci_h4p_info *info)
+{
+ /*
+ * Test Sequence:
+ * Host de-asserts the BT_WAKE_UP line.
+ * Host polls the UART_CTS line, waiting for it to be de-asserted.
+ * Host asserts the BT_WAKE_UP line.
+ * Host polls the UART_CTS line, waiting for it to be asserted.
+ * Host de-asserts the BT_WAKE_UP line (allow the Bluetooth device to
+ * sleep).
+ * Host polls the UART_CTS line, waiting for it to be de-asserted.
+ */
+ int err;
+ int ret = -ECOMM;
+
+ if (!info)
+ return -EINVAL;
+
+ /* Disable wakeup interrupts */
+ disable_irq(gpio_to_irq(info->host_wakeup_gpio));
+
+ gpio_set_value(info->bt_wakeup_gpio, 0);
+ err = hci_h4p_wait_for_cts(info, 0, 100);
+ if (err) {
+ dev_warn(info->dev, "bt_wakeup_test: fail: "
+ "CTS low timed out: %d\n", err);
+ goto out;
+ }
+
+ gpio_set_value(info->bt_wakeup_gpio, 1);
+ err = hci_h4p_wait_for_cts(info, 1, 100);
+ if (err) {
+ dev_warn(info->dev, "bt_wakeup_test: fail: "
+ "CTS high timed out: %d\n", err);
+ goto out;
+ }
+
+ gpio_set_value(info->bt_wakeup_gpio, 0);
+ err = hci_h4p_wait_for_cts(info, 0, 100);
+ if (err) {
+ dev_warn(info->dev, "bt_wakeup_test: fail: "
+ "CTS re-low timed out: %d\n", err);
+ goto out;
+ }
+
+ ret = 0;
+
+out:
+
+ /* Re-enable wakeup interrupts */
+ enable_irq(gpio_to_irq(info->host_wakeup_gpio));
+
+ return ret;
+}
+
+static int hci_h4p_hci_open(struct hci_dev *hdev)
+{
+ struct hci_h4p_info *info;
+ int err, retries = 0;
+ struct sk_buff_head fw_queue;
+ unsigned long flags;
+
+ info = hci_get_drvdata(hdev);
+
+ if (test_bit(HCI_RUNNING, &hdev->flags))
+ return 0;
+
+ /* TI1271 has HW bug and boot up might fail. Retry up to three times */
+again:
+
+ info->rx_enabled = 1;
+ info->rx_state = WAIT_FOR_PKT_TYPE;
+ info->rx_count = 0;
+ info->garbage_bytes = 0;
+ info->rx_skb = NULL;
+ info->pm_enabled = 0;
+ init_completion(&info->fw_completion);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 1);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 1);
+ skb_queue_head_init(&fw_queue);
+
+ err = hci_h4p_reset(info);
+ if (err < 0)
+ goto err_clean;
+
+ hci_h4p_set_auto_ctsrts(info, 1, UART_EFR_CTS | UART_EFR_RTS);
+ info->autorts = 1;
+
+ err = hci_h4p_send_negotiation(info);
+
+ err = hci_h4p_read_fw(info, &fw_queue);
+ if (err < 0) {
+ dev_err(info->dev, "Cannot read firmware\n");
+ goto err_clean;
+ }
+
+ err = hci_h4p_send_fw(info, &fw_queue);
+ if (err < 0) {
+ dev_err(info->dev, "Sending firmware failed.\n");
+ goto err_clean;
+ }
+
+ info->pm_enabled = 1;
+
+ err = hci_h4p_bt_wakeup_test(info);
+ if (err < 0) {
+ dev_err(info->dev, "BT wakeup test failed.\n");
+ goto err_clean;
+ }
+
+ spin_lock_irqsave(&info->lock, flags);
+ info->rx_enabled = gpio_get_value(info->host_wakeup_gpio);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, info->rx_enabled);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 0);
+
+ kfree_skb(info->alive_cmd_skb);
+ info->alive_cmd_skb = NULL;
+ set_bit(HCI_RUNNING, &hdev->flags);
+
+ BT_DBG("hci up and running");
+ return 0;
+
+err_clean:
+ hci_h4p_hci_flush(hdev);
+ hci_h4p_reset_uart(info);
+ del_timer_sync(&info->lazy_release);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 0);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 0);
+ gpio_set_value(info->reset_gpio, 0);
+ gpio_set_value(info->bt_wakeup_gpio, 0);
+ skb_queue_purge(&fw_queue);
+ kfree_skb(info->alive_cmd_skb);
+ info->alive_cmd_skb = NULL;
+ kfree_skb(info->rx_skb);
+ info->rx_skb = NULL;
+
+ if (retries++ < 3) {
+ dev_err(info->dev, "FW loading try %d fail. Retry.\n", retries);
+ goto again;
+ }
+
+ return err;
+}
+
+static int hci_h4p_hci_close(struct hci_dev *hdev)
+{
+ struct hci_h4p_info *info = hci_get_drvdata(hdev);
+
+ if (!test_and_clear_bit(HCI_RUNNING, &hdev->flags))
+ return 0;
+
+ hci_h4p_hci_flush(hdev);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 1);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 1);
+ hci_h4p_reset_uart(info);
+ del_timer_sync(&info->lazy_release);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 0);
+ hci_h4p_set_clk(info, &info->rx_clocks_en, 0);
+ gpio_set_value(info->reset_gpio, 0);
+ gpio_set_value(info->bt_wakeup_gpio, 0);
+ kfree_skb(info->rx_skb);
+
+ return 0;
+}
+
+static int hci_h4p_hci_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
+{
+ struct hci_h4p_info *info;
+ int err = 0;
+
+ BT_DBG("dev %p, skb %p", hdev, skb);
+
+ info = hci_get_drvdata(hdev);
+
+ if (!test_bit(HCI_RUNNING, &hdev->flags)) {
+ dev_warn(info->dev, "Frame for non-running device\n");
+ return -EIO;
+ }
+
+ switch (bt_cb(skb)->pkt_type) {
+ case HCI_COMMAND_PKT:
+ hdev->stat.cmd_tx++;
+ break;
+ case HCI_ACLDATA_PKT:
+ hdev->stat.acl_tx++;
+ break;
+ case HCI_SCODATA_PKT:
+ hdev->stat.sco_tx++;
+ break;
+ }
+
+ /* Push frame type to skb */
+ *skb_push(skb, 1) = (bt_cb(skb)->pkt_type);
+ /* We should allways send word aligned data to h4+ devices */
+ if (skb->len % 2) {
+ err = skb_pad(skb, 1);
+ if (!err)
+ *skb_put(skb, 1) = 0x00;
+ }
+ if (err)
+ return err;
+
+ skb_queue_tail(&info->txq, skb);
+ hci_h4p_enable_tx(info);
+
+ return 0;
+}
+
+static ssize_t hci_h4p_store_bdaddr(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct hci_h4p_info *info = dev_get_drvdata(dev);
+ unsigned int bdaddr[6];
+ int ret, i;
+
+ ret = sscanf(buf, "%2x:%2x:%2x:%2x:%2x:%2x\n",
+ &bdaddr[0], &bdaddr[1], &bdaddr[2],
+ &bdaddr[3], &bdaddr[4], &bdaddr[5]);
+
+ if (ret != 6)
+ return -EINVAL;
+
+ for (i = 0; i < 6; i++) {
+ if (bdaddr[i] > 0xff)
+ return -EINVAL;
+ info->bd_addr[i] = bdaddr[i] & 0xff;
+ }
+
+ return count;
+}
+
+static ssize_t hci_h4p_show_bdaddr(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct hci_h4p_info *info = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%pMR\n", info->bd_addr);
+}
+
+static DEVICE_ATTR(bdaddr, S_IRUGO | S_IWUSR, hci_h4p_show_bdaddr,
+ hci_h4p_store_bdaddr);
+
+static int hci_h4p_sysfs_create_files(struct device *dev)
+{
+ return device_create_file(dev, &dev_attr_bdaddr);
+}
+
+static void hci_h4p_sysfs_remove_files(struct device *dev)
+{
+ device_remove_file(dev, &dev_attr_bdaddr);
+}
+
+static int hci_h4p_register_hdev(struct hci_h4p_info *info)
+{
+ struct hci_dev *hdev;
+
+ /* Initialize and register HCI device */
+
+ hdev = hci_alloc_dev();
+ if (!hdev) {
+ dev_err(info->dev, "Can't allocate memory for device\n");
+ return -ENOMEM;
+ }
+ info->hdev = hdev;
+
+ hdev->bus = HCI_UART;
+ hci_set_drvdata(hdev, info);
+
+ hdev->open = hci_h4p_hci_open;
+ hdev->close = hci_h4p_hci_close;
+ hdev->flush = hci_h4p_hci_flush;
+ hdev->send = hci_h4p_hci_send_frame;
+ set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
+
+ SET_HCIDEV_DEV(hdev, info->dev);
+
+ if (hci_h4p_sysfs_create_files(info->dev) < 0) {
+ dev_err(info->dev, "failed to create sysfs files\n");
+ goto free;
+ }
+
+ if (hci_register_dev(hdev) >= 0)
+ return 0;
+
+ dev_err(info->dev, "hci_register failed %s.\n", hdev->name);
+ hci_h4p_sysfs_remove_files(info->dev);
+free:
+ hci_free_dev(info->hdev);
+ return -ENODEV;
+}
+
+static int hci_h4p_probe(struct platform_device *pdev)
+{
+ struct hci_h4p_platform_data *bt_plat_data;
+ struct hci_h4p_info *info;
+ int err;
+
+ dev_info(&pdev->dev, "Registering HCI H4P device\n");
+ info = devm_kzalloc(&pdev->dev, sizeof(struct hci_h4p_info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
+
+ info->dev = &pdev->dev;
+ info->tx_enabled = 1;
+ info->rx_enabled = 1;
+ spin_lock_init(&info->lock);
+ spin_lock_init(&info->clocks_lock);
+ skb_queue_head_init(&info->txq);
+
+ if (pdev->dev.platform_data == NULL) {
+ dev_err(&pdev->dev, "Could not get Bluetooth config data\n");
+ return -ENODATA;
+ }
+
+ bt_plat_data = pdev->dev.platform_data;
+ info->chip_type = bt_plat_data->chip_type;
+ info->bt_wakeup_gpio = bt_plat_data->bt_wakeup_gpio;
+ info->host_wakeup_gpio = bt_plat_data->host_wakeup_gpio;
+ info->reset_gpio = bt_plat_data->reset_gpio;
+ info->reset_gpio_shared = bt_plat_data->reset_gpio_shared;
+ info->bt_sysclk = bt_plat_data->bt_sysclk;
+
+ BT_DBG("RESET gpio: %d", info->reset_gpio);
+ BT_DBG("BTWU gpio: %d", info->bt_wakeup_gpio);
+ BT_DBG("HOSTWU gpio: %d", info->host_wakeup_gpio);
+ BT_DBG("sysclk: %d", info->bt_sysclk);
+
+ init_completion(&info->test_completion);
+ complete_all(&info->test_completion);
+
+ if (!info->reset_gpio_shared) {
+ err = devm_gpio_request_one(&pdev->dev, info->reset_gpio,
+ GPIOF_OUT_INIT_LOW, "bt_reset");
+ if (err < 0) {
+ dev_err(&pdev->dev, "Cannot get GPIO line %d\n",
+ info->reset_gpio);
+ return err;
+ }
+ }
+
+ err = devm_gpio_request_one(&pdev->dev, info->bt_wakeup_gpio,
+ GPIOF_OUT_INIT_LOW, "bt_wakeup");
+
+ if (err < 0) {
+ dev_err(info->dev, "Cannot get GPIO line 0x%d",
+ info->bt_wakeup_gpio);
+ return err;
+ }
+
+ err = devm_gpio_request_one(&pdev->dev, info->host_wakeup_gpio,
+ GPIOF_DIR_IN, "host_wakeup");
+ if (err < 0) {
+ dev_err(info->dev, "Cannot get GPIO line %d",
+ info->host_wakeup_gpio);
+ return err;
+ }
+
+ info->irq = bt_plat_data->uart_irq;
+ info->uart_base = devm_ioremap(&pdev->dev, bt_plat_data->uart_base, SZ_2K);
+ info->uart_iclk = devm_clk_get(&pdev->dev, bt_plat_data->uart_iclk);
+ info->uart_fclk = devm_clk_get(&pdev->dev, bt_plat_data->uart_fclk);
+
+ err = devm_request_irq(&pdev->dev, info->irq, hci_h4p_interrupt, IRQF_DISABLED,
+ "hci_h4p", info);
+ if (err < 0) {
+ dev_err(info->dev, "hci_h4p: unable to get IRQ %d\n", info->irq);
+ return err;
+ }
+
+ err = devm_request_irq(&pdev->dev, gpio_to_irq(info->host_wakeup_gpio),
+ hci_h4p_wakeup_interrupt, IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING | IRQF_DISABLED,
+ "hci_h4p_wkup", info);
+ if (err < 0) {
+ dev_err(info->dev, "hci_h4p: unable to get wakeup IRQ %d\n",
+ gpio_to_irq(info->host_wakeup_gpio));
+ return err;
+ }
+
+ err = irq_set_irq_wake(gpio_to_irq(info->host_wakeup_gpio), 1);
+ if (err < 0) {
+ dev_err(info->dev, "hci_h4p: unable to set wakeup for IRQ %d\n",
+ gpio_to_irq(info->host_wakeup_gpio));
+ return err;
+ }
+
+ init_timer_deferrable(&info->lazy_release);
+ info->lazy_release.function = hci_h4p_lazy_clock_release;
+ info->lazy_release.data = (unsigned long)info;
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 1);
+ err = hci_h4p_reset_uart(info);
+ if (err < 0)
+ return err;
+ gpio_set_value(info->reset_gpio, 0);
+ hci_h4p_set_clk(info, &info->tx_clocks_en, 0);
+
+ platform_set_drvdata(pdev, info);
+
+ if (hci_h4p_register_hdev(info) < 0) {
+ dev_err(info->dev, "failed to register hci_h4p hci device\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int hci_h4p_remove(struct platform_device *pdev)
+{
+ struct hci_h4p_info *info;
+
+ info = platform_get_drvdata(pdev);
+
+ hci_h4p_sysfs_remove_files(info->dev);
+ hci_h4p_hci_close(info->hdev);
+ hci_unregister_dev(info->hdev);
+ hci_free_dev(info->hdev);
+
+ return 0;
+}
+
+static struct platform_driver hci_h4p_driver = {
+ .probe = hci_h4p_probe,
+ .remove = hci_h4p_remove,
+ .driver = {
+ .name = "hci_h4p",
+ },
+};
+
+module_platform_driver(hci_h4p_driver);
+
+MODULE_ALIAS("platform:hci_h4p");
+MODULE_DESCRIPTION("Bluetooth h4 driver with nokia extensions");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Ville Tervo");
+MODULE_FIRMWARE(FW_NAME_TI1271_PRELE);
+MODULE_FIRMWARE(FW_NAME_TI1271_LE);
+MODULE_FIRMWARE(FW_NAME_TI1271);
+MODULE_FIRMWARE(FW_NAME_BCM2048);
+MODULE_FIRMWARE(FW_NAME_CSR);
diff --git a/drivers/staging/nokia_h4p/nokia_fw-bcm.c b/drivers/staging/nokia_h4p/nokia_fw-bcm.c
new file mode 100644
index 0000000..e8912bf
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_fw-bcm.c
@@ -0,0 +1,147 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2005-2008 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/serial_reg.h>
+
+#include "hci_h4p.h"
+
+static int hci_h4p_bcm_set_bdaddr(struct hci_h4p_info *info, struct sk_buff *skb)
+{
+ int i;
+ static const u8 nokia_oui[3] = {0x00, 0x1f, 0xdf};
+ int not_valid;
+
+ not_valid = 1;
+ for (i = 0; i < 6; i++) {
+ if (info->bd_addr[i] != 0x00) {
+ not_valid = 0;
+ break;
+ }
+ }
+
+ if (not_valid) {
+ dev_info(info->dev, "Valid bluetooth address not found, setting some random\n");
+ /* When address is not valid, use some random but Nokia MAC */
+ memcpy(info->bd_addr, nokia_oui, 3);
+ get_random_bytes(info->bd_addr + 3, 3);
+ }
+
+ for (i = 0; i < 6; i++)
+ skb->data[9 - i] = info->bd_addr[i];
+
+ return 0;
+}
+
+void hci_h4p_bcm_parse_fw_event(struct hci_h4p_info *info, struct sk_buff *skb)
+{
+ struct sk_buff *fw_skb;
+ int err;
+ unsigned long flags;
+
+ if (skb->data[5] != 0x00) {
+ dev_err(info->dev, "Firmware sending command failed 0x%.2x\n",
+ skb->data[5]);
+ info->fw_error = -EPROTO;
+ }
+
+ kfree_skb(skb);
+
+ fw_skb = skb_dequeue(info->fw_q);
+ if (fw_skb == NULL || info->fw_error) {
+ complete(&info->fw_completion);
+ return;
+ }
+
+ if (fw_skb->data[1] == 0x01 && fw_skb->data[2] == 0xfc && fw_skb->len >= 10) {
+ BT_DBG("Setting bluetooth address");
+ err = hci_h4p_bcm_set_bdaddr(info, fw_skb);
+ if (err < 0) {
+ kfree_skb(fw_skb);
+ info->fw_error = err;
+ complete(&info->fw_completion);
+ return;
+ }
+ }
+
+ skb_queue_tail(&info->txq, fw_skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+}
+
+
+int hci_h4p_bcm_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue)
+{
+ struct sk_buff *skb;
+ unsigned long flags, time;
+
+ info->fw_error = 0;
+
+ BT_DBG("Sending firmware");
+
+ time = jiffies;
+
+ info->fw_q = fw_queue;
+ skb = skb_dequeue(fw_queue);
+ if (!skb)
+ return -ENODATA;
+
+ BT_DBG("Sending commands");
+
+ /*
+ * Disable smart-idle as UART TX interrupts
+ * are not wake-up capable
+ */
+ hci_h4p_smart_idle(info, 0);
+
+ /* Check if this is bd_address packet */
+ init_completion(&info->fw_completion);
+ skb_queue_tail(&info->txq, skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ if (!wait_for_completion_timeout(&info->fw_completion,
+ msecs_to_jiffies(2000))) {
+ dev_err(info->dev, "No reply to fw command\n");
+ return -ETIMEDOUT;
+ }
+
+ if (info->fw_error) {
+ dev_err(info->dev, "FW error\n");
+ return -EPROTO;
+ }
+
+ BT_DBG("Firmware sent in %d msecs",
+ jiffies_to_msecs(jiffies-time));
+
+ hci_h4p_set_auto_ctsrts(info, 0, UART_EFR_RTS);
+ hci_h4p_set_rts(info, 0);
+ hci_h4p_change_speed(info, BC4_MAX_BAUD_RATE);
+ hci_h4p_set_auto_ctsrts(info, 1, UART_EFR_RTS);
+
+ return 0;
+}
diff --git a/drivers/staging/nokia_h4p/nokia_fw-csr.c b/drivers/staging/nokia_h4p/nokia_fw-csr.c
new file mode 100644
index 0000000..e39c4a3
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_fw-csr.c
@@ -0,0 +1,150 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2005-2008 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/serial_reg.h>
+
+#include "hci_h4p.h"
+
+void hci_h4p_bc4_parse_fw_event(struct hci_h4p_info *info, struct sk_buff *skb)
+{
+ /* Check if this is fw packet */
+ if (skb->data[0] != 0xff) {
+ hci_recv_frame(info->hdev, skb);
+ return;
+ }
+
+ if (skb->data[11] || skb->data[12]) {
+ dev_err(info->dev, "Firmware sending command failed\n");
+ info->fw_error = -EPROTO;
+ }
+
+ kfree_skb(skb);
+ complete(&info->fw_completion);
+}
+
+int hci_h4p_bc4_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue)
+{
+ static const u8 nokia_oui[3] = {0x00, 0x19, 0x4F};
+ struct sk_buff *skb;
+ unsigned int offset;
+ int retries, count, i, not_valid;
+ unsigned long flags;
+
+ info->fw_error = 0;
+
+ BT_DBG("Sending firmware");
+ skb = skb_dequeue(fw_queue);
+
+ if (!skb)
+ return -ENOMSG;
+
+ /* Check if this is bd_address packet */
+ if (skb->data[15] == 0x01 && skb->data[16] == 0x00) {
+ offset = 21;
+ skb->data[offset + 1] = 0x00;
+ skb->data[offset + 5] = 0x00;
+
+ not_valid = 1;
+ for (i = 0; i < 6; i++) {
+ if (info->bd_addr[i] != 0x00) {
+ not_valid = 0;
+ break;
+ }
+ }
+
+ if (not_valid) {
+ dev_info(info->dev, "Valid bluetooth address not found,"
+ " setting some random\n");
+ /* When address is not valid, use some random */
+ memcpy(info->bd_addr, nokia_oui, 3);
+ get_random_bytes(info->bd_addr + 3, 3);
+ }
+
+ skb->data[offset + 7] = info->bd_addr[0];
+ skb->data[offset + 6] = info->bd_addr[1];
+ skb->data[offset + 4] = info->bd_addr[2];
+ skb->data[offset + 0] = info->bd_addr[3];
+ skb->data[offset + 3] = info->bd_addr[4];
+ skb->data[offset + 2] = info->bd_addr[5];
+ }
+
+ for (count = 1; ; count++) {
+ BT_DBG("Sending firmware command %d", count);
+ init_completion(&info->fw_completion);
+ skb_queue_tail(&info->txq, skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ skb = skb_dequeue(fw_queue);
+ if (!skb)
+ break;
+
+ if (!wait_for_completion_timeout(&info->fw_completion,
+ msecs_to_jiffies(1000))) {
+ dev_err(info->dev, "No reply to fw command\n");
+ return -ETIMEDOUT;
+ }
+
+ if (info->fw_error) {
+ dev_err(info->dev, "FW error\n");
+ return -EPROTO;
+ }
+ };
+
+ /* Wait for chip warm reset */
+ retries = 100;
+ while ((!skb_queue_empty(&info->txq) ||
+ !(hci_h4p_inb(info, UART_LSR) & UART_LSR_TEMT)) &&
+ retries--) {
+ msleep(10);
+ }
+ if (!retries) {
+ dev_err(info->dev, "Transmitter not empty\n");
+ return -ETIMEDOUT;
+ }
+
+ hci_h4p_change_speed(info, BC4_MAX_BAUD_RATE);
+
+ if (hci_h4p_wait_for_cts(info, 1, 100)) {
+ dev_err(info->dev, "cts didn't deassert after final speed\n");
+ return -ETIMEDOUT;
+ }
+
+ retries = 100;
+ do {
+ init_completion(&info->init_completion);
+ hci_h4p_send_alive_packet(info);
+ retries--;
+ } while (!wait_for_completion_timeout(&info->init_completion, 100) &&
+ retries > 0);
+
+ if (!retries) {
+ dev_err(info->dev, "No alive reply after speed change\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
diff --git a/drivers/staging/nokia_h4p/nokia_fw-ti1273.c b/drivers/staging/nokia_h4p/nokia_fw-ti1273.c
new file mode 100644
index 0000000..f5500f7
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_fw-ti1273.c
@@ -0,0 +1,110 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2009 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/skbuff.h>
+#include <linux/delay.h>
+#include <linux/serial_reg.h>
+
+#include "hci_h4p.h"
+
+static struct sk_buff_head *fw_q;
+
+void hci_h4p_ti1273_parse_fw_event(struct hci_h4p_info *info,
+ struct sk_buff *skb)
+{
+ struct sk_buff *fw_skb;
+ unsigned long flags;
+
+ if (skb->data[5] != 0x00) {
+ dev_err(info->dev, "Firmware sending command failed 0x%.2x\n",
+ skb->data[5]);
+ info->fw_error = -EPROTO;
+ }
+
+ kfree_skb(skb);
+
+ fw_skb = skb_dequeue(fw_q);
+ if (fw_skb == NULL || info->fw_error) {
+ complete(&info->fw_completion);
+ return;
+ }
+
+ skb_queue_tail(&info->txq, fw_skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+}
+
+
+int hci_h4p_ti1273_send_fw(struct hci_h4p_info *info,
+ struct sk_buff_head *fw_queue)
+{
+ struct sk_buff *skb;
+ unsigned long flags, time;
+
+ info->fw_error = 0;
+
+ BT_DBG("Sending firmware");
+
+ time = jiffies;
+
+ fw_q = fw_queue;
+ skb = skb_dequeue(fw_queue);
+ if (!skb)
+ return -ENODATA;
+
+ BT_DBG("Sending commands");
+ /* Check if this is bd_address packet */
+ init_completion(&info->fw_completion);
+ hci_h4p_smart_idle(info, 0);
+ skb_queue_tail(&info->txq, skb);
+ spin_lock_irqsave(&info->lock, flags);
+ hci_h4p_outb(info, UART_IER, hci_h4p_inb(info, UART_IER) |
+ UART_IER_THRI);
+ spin_unlock_irqrestore(&info->lock, flags);
+
+ if (!wait_for_completion_timeout(&info->fw_completion,
+ msecs_to_jiffies(2000))) {
+ dev_err(info->dev, "No reply to fw command\n");
+ return -ETIMEDOUT;
+ }
+
+ if (info->fw_error) {
+ dev_err(info->dev, "FW error\n");
+ return -EPROTO;
+ }
+
+ BT_DBG("Firmware sent in %d msecs",
+ jiffies_to_msecs(jiffies-time));
+
+ hci_h4p_set_auto_ctsrts(info, 0, UART_EFR_RTS);
+ hci_h4p_set_rts(info, 0);
+ hci_h4p_change_speed(info, BC4_MAX_BAUD_RATE);
+ if (hci_h4p_wait_for_cts(info, 1, 100)) {
+ dev_err(info->dev,
+ "cts didn't go down after final speed change\n");
+ return -ETIMEDOUT;
+ }
+ hci_h4p_set_auto_ctsrts(info, 1, UART_EFR_RTS);
+
+ return 0;
+}
diff --git a/drivers/staging/nokia_h4p/nokia_fw.c b/drivers/staging/nokia_h4p/nokia_fw.c
new file mode 100644
index 0000000..cfea61c
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_fw.c
@@ -0,0 +1,195 @@
+/*
+ * This file is part of hci_h4p bluetooth driver
+ *
+ * Copyright (C) 2005, 2006 Nokia Corporation.
+ *
+ * Contact: Ville Tervo <ville.tervo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/skbuff.h>
+#include <linux/firmware.h>
+#include <linux/clk.h>
+
+#include <net/bluetooth/bluetooth.h>
+
+#include "hci_h4p.h"
+
+static int fw_pos;
+
+/* Firmware handling */
+static int hci_h4p_open_firmware(struct hci_h4p_info *info,
+ const struct firmware **fw_entry)
+{
+ int err;
+
+ fw_pos = 0;
+ BT_DBG("Opening firmware man_id 0x%.2x ver_id 0x%.2x",
+ info->man_id, info->ver_id);
+ switch (info->man_id) {
+ case H4P_ID_TI1271:
+ switch (info->ver_id) {
+ case 0xe1:
+ err = request_firmware(fw_entry, FW_NAME_TI1271_PRELE,
+ info->dev);
+ break;
+ case 0xd1:
+ case 0xf1:
+ err = request_firmware(fw_entry, FW_NAME_TI1271_LE,
+ info->dev);
+ break;
+ default:
+ err = request_firmware(fw_entry, FW_NAME_TI1271,
+ info->dev);
+ }
+ break;
+ case H4P_ID_CSR:
+ err = request_firmware(fw_entry, FW_NAME_CSR, info->dev);
+ break;
+ case H4P_ID_BCM2048:
+ err = request_firmware(fw_entry, FW_NAME_BCM2048, info->dev);
+ break;
+ default:
+ dev_err(info->dev, "Invalid chip type\n");
+ *fw_entry = NULL;
+ err = -EINVAL;
+ }
+
+ return err;
+}
+
+static void hci_h4p_close_firmware(const struct firmware *fw_entry)
+{
+ release_firmware(fw_entry);
+}
+
+/* Read fw. Return length of the command. If no more commands in
+ * fw 0 is returned. In error case return value is negative.
+ */
+static int hci_h4p_read_fw_cmd(struct hci_h4p_info *info, struct sk_buff **skb,
+ const struct firmware *fw_entry, gfp_t how)
+{
+ unsigned int cmd_len;
+
+ if (fw_pos >= fw_entry->size)
+ return 0;
+
+ if (fw_pos + 2 > fw_entry->size) {
+ dev_err(info->dev, "Corrupted firmware image 1\n");
+ return -EMSGSIZE;
+ }
+
+ cmd_len = fw_entry->data[fw_pos++];
+ cmd_len += fw_entry->data[fw_pos++] << 8;
+ if (cmd_len == 0)
+ return 0;
+
+ if (fw_pos + cmd_len > fw_entry->size) {
+ dev_err(info->dev, "Corrupted firmware image 2\n");
+ return -EMSGSIZE;
+ }
+
+ *skb = bt_skb_alloc(cmd_len, how);
+ if (!*skb) {
+ dev_err(info->dev, "Cannot reserve memory for buffer\n");
+ return -ENOMEM;
+ }
+ memcpy(skb_put(*skb, cmd_len), &fw_entry->data[fw_pos], cmd_len);
+
+ fw_pos += cmd_len;
+
+ return (*skb)->len;
+}
+
+int hci_h4p_read_fw(struct hci_h4p_info *info, struct sk_buff_head *fw_queue)
+{
+ const struct firmware *fw_entry = NULL;
+ struct sk_buff *skb = NULL;
+ int err;
+
+ err = hci_h4p_open_firmware(info, &fw_entry);
+ if (err < 0 || !fw_entry)
+ goto err_clean;
+
+ while ((err = hci_h4p_read_fw_cmd(info, &skb, fw_entry, GFP_KERNEL))) {
+ if (err < 0 || !skb)
+ goto err_clean;
+
+ skb_queue_tail(fw_queue, skb);
+ }
+
+ /* Chip detection code does neg and alive stuff
+ * discard two first skbs */
+ skb = skb_dequeue(fw_queue);
+ if (!skb) {
+ err = -EMSGSIZE;
+ goto err_clean;
+ }
+ kfree_skb(skb);
+ skb = skb_dequeue(fw_queue);
+ if (!skb) {
+ err = -EMSGSIZE;
+ goto err_clean;
+ }
+ kfree_skb(skb);
+
+err_clean:
+ hci_h4p_close_firmware(fw_entry);
+ return err;
+}
+
+int hci_h4p_send_fw(struct hci_h4p_info *info, struct sk_buff_head *fw_queue)
+{
+ int err;
+
+ switch (info->man_id) {
+ case H4P_ID_CSR:
+ err = hci_h4p_bc4_send_fw(info, fw_queue);
+ break;
+ case H4P_ID_TI1271:
+ err = hci_h4p_ti1273_send_fw(info, fw_queue);
+ break;
+ case H4P_ID_BCM2048:
+ err = hci_h4p_bcm_send_fw(info, fw_queue);
+ break;
+ default:
+ dev_err(info->dev, "Don't know how to send firmware\n");
+ err = -EINVAL;
+ }
+
+ return err;
+}
+
+void hci_h4p_parse_fw_event(struct hci_h4p_info *info, struct sk_buff *skb)
+{
+ switch (info->man_id) {
+ case H4P_ID_CSR:
+ hci_h4p_bc4_parse_fw_event(info, skb);
+ break;
+ case H4P_ID_TI1271:
+ hci_h4p_ti1273_parse_fw_event(info, skb);
+ break;
+ case H4P_ID_BCM2048:
+ hci_h4p_bcm_parse_fw_event(info, skb);
+ break;
+ default:
+ dev_err(info->dev, "Don't know how to parse fw event\n");
+ info->fw_error = -EINVAL;
+ }
+
+ return;
+}
diff --git a/drivers/staging/nokia_h4p/nokia_uart.c b/drivers/staging/nokia_h4p/nokia_uart.c
new file mode 100644
index 0000000..0fb57de
--- /dev/null
+++ b/drivers/staging/nokia_h4p/nokia_uart.c
@@ -0,0 +1,199 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2005, 2006 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/serial_reg.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include <linux/io.h>
+
+#include "hci_h4p.h"
+
+inline void hci_h4p_outb(struct hci_h4p_info *info, unsigned int offset, u8 val)
+{
+ __raw_writeb(val, info->uart_base + (offset << 2));
+}
+
+inline u8 hci_h4p_inb(struct hci_h4p_info *info, unsigned int offset)
+{
+ return __raw_readb(info->uart_base + (offset << 2));
+}
+
+void hci_h4p_set_rts(struct hci_h4p_info *info, int active)
+{
+ u8 b;
+
+ b = hci_h4p_inb(info, UART_MCR);
+ if (active)
+ b |= UART_MCR_RTS;
+ else
+ b &= ~UART_MCR_RTS;
+ hci_h4p_outb(info, UART_MCR, b);
+}
+
+int hci_h4p_wait_for_cts(struct hci_h4p_info *info, int active,
+ int timeout_ms)
+{
+ unsigned long timeout;
+ int state;
+
+ timeout = jiffies + msecs_to_jiffies(timeout_ms);
+ for (;;) {
+ state = hci_h4p_inb(info, UART_MSR) & UART_MSR_CTS;
+ if (active) {
+ if (state)
+ return 0;
+ } else {
+ if (!state)
+ return 0;
+ }
+ if (time_after(jiffies, timeout))
+ return -ETIMEDOUT;
+ msleep(1);
+ }
+}
+
+void __hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which)
+{
+ u8 lcr, b;
+
+ lcr = hci_h4p_inb(info, UART_LCR);
+ hci_h4p_outb(info, UART_LCR, 0xbf);
+ b = hci_h4p_inb(info, UART_EFR);
+ if (on)
+ b |= which;
+ else
+ b &= ~which;
+ hci_h4p_outb(info, UART_EFR, b);
+ hci_h4p_outb(info, UART_LCR, lcr);
+}
+
+void hci_h4p_set_auto_ctsrts(struct hci_h4p_info *info, int on, u8 which)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->lock, flags);
+ __hci_h4p_set_auto_ctsrts(info, on, which);
+ spin_unlock_irqrestore(&info->lock, flags);
+}
+
+void hci_h4p_change_speed(struct hci_h4p_info *info, unsigned long speed)
+{
+ unsigned int divisor;
+ u8 lcr, mdr1;
+
+ BT_DBG("Setting speed %lu", speed);
+
+ if (speed >= 460800) {
+ divisor = UART_CLOCK / 13 / speed;
+ mdr1 = 3;
+ } else {
+ divisor = UART_CLOCK / 16 / speed;
+ mdr1 = 0;
+ }
+
+ /* Make sure UART mode is disabled */
+ hci_h4p_outb(info, UART_OMAP_MDR1, 7);
+
+ lcr = hci_h4p_inb(info, UART_LCR);
+ hci_h4p_outb(info, UART_LCR, UART_LCR_DLAB); /* Set DLAB */
+ hci_h4p_outb(info, UART_DLL, divisor & 0xff); /* Set speed */
+ hci_h4p_outb(info, UART_DLM, divisor >> 8);
+ hci_h4p_outb(info, UART_LCR, lcr);
+
+ /* Make sure UART mode is enabled */
+ hci_h4p_outb(info, UART_OMAP_MDR1, mdr1);
+}
+
+int hci_h4p_reset_uart(struct hci_h4p_info *info)
+{
+ int count = 0;
+
+ /* Reset the UART */
+ hci_h4p_outb(info, UART_OMAP_SYSC, UART_SYSC_OMAP_RESET);
+ while (!(hci_h4p_inb(info, UART_OMAP_SYSS) & UART_SYSS_RESETDONE)) {
+ if (count++ > 100) {
+ dev_err(info->dev, "hci_h4p: UART reset timeout\n");
+ return -ENODEV;
+ }
+ udelay(1);
+ }
+
+ return 0;
+}
+
+void hci_h4p_store_regs(struct hci_h4p_info *info)
+{
+ u16 lcr = 0;
+
+ lcr = hci_h4p_inb(info, UART_LCR);
+ hci_h4p_outb(info, UART_LCR, 0xBF);
+ info->dll = hci_h4p_inb(info, UART_DLL);
+ info->dlh = hci_h4p_inb(info, UART_DLM);
+ info->efr = hci_h4p_inb(info, UART_EFR);
+ hci_h4p_outb(info, UART_LCR, lcr);
+ info->mdr1 = hci_h4p_inb(info, UART_OMAP_MDR1);
+ info->ier = hci_h4p_inb(info, UART_IER);
+}
+
+void hci_h4p_restore_regs(struct hci_h4p_info *info)
+{
+ u16 lcr = 0;
+
+ hci_h4p_init_uart(info);
+
+ hci_h4p_outb(info, UART_OMAP_MDR1, 7);
+ lcr = hci_h4p_inb(info, UART_LCR);
+ hci_h4p_outb(info, UART_LCR, 0xBF);
+ hci_h4p_outb(info, UART_DLL, info->dll); /* Set speed */
+ hci_h4p_outb(info, UART_DLM, info->dlh);
+ hci_h4p_outb(info, UART_EFR, info->efr);
+ hci_h4p_outb(info, UART_LCR, lcr);
+ hci_h4p_outb(info, UART_OMAP_MDR1, info->mdr1);
+ hci_h4p_outb(info, UART_IER, info->ier);
+}
+
+void hci_h4p_init_uart(struct hci_h4p_info *info)
+{
+ u8 mcr, efr;
+
+ /* Enable and setup FIFO */
+ hci_h4p_outb(info, UART_OMAP_MDR1, 0x00);
+
+ hci_h4p_outb(info, UART_LCR, 0xbf);
+ efr = hci_h4p_inb(info, UART_EFR);
+ hci_h4p_outb(info, UART_EFR, UART_EFR_ECB);
+ hci_h4p_outb(info, UART_LCR, UART_LCR_DLAB);
+ mcr = hci_h4p_inb(info, UART_MCR);
+ hci_h4p_outb(info, UART_MCR, UART_MCR_TCRTLR);
+ hci_h4p_outb(info, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
+ (3 << 6) | (0 << 4));
+ hci_h4p_outb(info, UART_LCR, 0xbf);
+ hci_h4p_outb(info, UART_TI752_TLR, 0xed);
+ hci_h4p_outb(info, UART_TI752_TCR, 0xef);
+ hci_h4p_outb(info, UART_EFR, efr);
+ hci_h4p_outb(info, UART_LCR, UART_LCR_DLAB);
+ hci_h4p_outb(info, UART_MCR, 0x00);
+ hci_h4p_outb(info, UART_LCR, UART_LCR_WLEN8);
+ hci_h4p_outb(info, UART_IER, UART_IER_RDI);
+ hci_h4p_outb(info, UART_OMAP_SYSC, (1 << 0) | (1 << 2) | (2 << 3));
+}
diff --git a/include/linux/platform_data/bt-nokia-h4p.h b/include/linux/platform_data/bt-nokia-h4p.h
new file mode 100644
index 0000000..30d169d
--- /dev/null
+++ b/include/linux/platform_data/bt-nokia-h4p.h
@@ -0,0 +1,38 @@
+/*
+ * This file is part of Nokia H4P bluetooth driver
+ *
+ * Copyright (C) 2010 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+
+/**
+ * struct hci_h4p_platform data - hci_h4p Platform data structure
+ */
+struct hci_h4p_platform_data {
+ int chip_type;
+ int bt_sysclk;
+ unsigned int bt_wakeup_gpio;
+ unsigned int host_wakeup_gpio;
+ unsigned int reset_gpio;
+ int reset_gpio_shared;
+ unsigned int uart_irq;
+ phys_addr_t uart_base;
+ const char *uart_iclk;
+ const char *uart_fclk;
+ void (*set_pm_limits)(struct device *dev, bool set);
+};
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

----- End forwarded message -----
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2014-01-21 22:01    [W:2.323 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site