lkml.org 
[lkml]   [2013]   [Sep]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] thermal: bcm281xx: Add thermal driver
On 23-09-2013 13:51, Wendy Ng wrote:
> This adds the support for reading out temperature from Broadcom bcm281xx
> SoCs.
>
> Signed-off-by: Wendy Ng <wendy.ng@broadcom.com>
> Reviewed-by: Markus Mayer <mmayer@broadcom.com>
> Reviewed-by: Christian Daudt <csd@broadcom.com>
> ---
> .../bindings/thermal/bcm-kona-thermal.txt | 18 +++
> drivers/thermal/Kconfig | 10 ++
> drivers/thermal/Makefile | 1 +
> drivers/thermal/bcm_thermal.c | 170 ++++++++++++++++++++
> 4 files changed, 199 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> create mode 100644 drivers/thermal/bcm_thermal.c
>
> diff --git a/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt b/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> new file mode 100644
> index 0000000..acca99e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/bcm-kona-thermal.txt
> @@ -0,0 +1,18 @@
> +* Broadcom Kona Thermal Management Unit
> +
> +This version is for the BCM281xx family of SoCs.
> +
> +Required properties:
> +- compatible : "brcm,bcm11351-thermal", "brcm,kona-thermal"
> +- reg : Address range of the thermal register
> +- thermal-name: this entry must be specified and it will be passed into
> +thermal_zone_device_register(). This name will also be reported under Hwmon
> +sysfs 'name' attribute.
> +
> +Example:
> + thermal@34008000 {
> + compatible = "brcm,bcm11351-thermal", "brcm,kona-thermal";
> + reg = <0x34008000 0x0024>;
> + thermal-name = "bcm_kona_therm";
> + status = "disabled";
> + };
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index dbfc390..7f823f0 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -134,6 +134,16 @@ config KIRKWOOD_THERMAL
> Support for the Kirkwood thermal sensor driver into the Linux thermal
> framework. Only kirkwood 88F6282 and 88F6283 have this sensor.
>
> +config BCM_THERMAL
> + tristate "Temperature sensor on Broadcom BCM281xx family of SoCs"
> + depends on ARCH_BCM
> + default y
> + help
> + If you say yes here you get support for TMU (Thermal Management
> + Unit) on Broadcom BCM281xx family of SoCs. This provides thermal
> + monitoring of CPU clusters, graphics, and SoC glue, but does not
> + include monitoring of charger temperature.
> +
> config DOVE_THERMAL
> tristate "Temperature sensor on Marvell Dove SoCs"
> depends on ARCH_DOVE
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 584b363..3ea8c1c 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -21,6 +21,7 @@ obj-$(CONFIG_SPEAR_THERMAL) += spear_thermal.o
> obj-$(CONFIG_RCAR_THERMAL) += rcar_thermal.o
> obj-$(CONFIG_KIRKWOOD_THERMAL) += kirkwood_thermal.o
> obj-y += samsung/
> +obj-$(CONFIG_BCM_THERMAL) += bcm_thermal.o
> obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o
> obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o
> obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o
> diff --git a/drivers/thermal/bcm_thermal.c b/drivers/thermal/bcm_thermal.c
> new file mode 100644
> index 0000000..131d3c4
> --- /dev/null
> +++ b/drivers/thermal/bcm_thermal.c
> @@ -0,0 +1,170 @@
> +/*
> + * Copyright 2013 Broadcom Corporation.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License, version 2,
> + * as published by the Free Software Foundation (the "GPL").
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * A copy of the GPL is available at http://www.broadcom.com/licenses/GPLv2.php,
> + * or by writing to the Free Software Foundation, Inc.,
> + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
> + */
> +
> +/**
> +* Broadcom Thermal Management Unit - bcm_tmu
> +*/
> +#include <linux/module.h>
> +#include <linux/err.h>
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/io.h>
> +#include <linux/thermal.h>
> +#include <linux/of.h>
> +
> +/* From TMON Register Database */
> +#define TMON_TEMP_VAL_OFFSET 0x0000001c
> +#define TMON_TEMP_VAL_TEMP_VAL_SHIFT 0
> +#define TMON_TEMP_VAL_TEMP_VAL_MASK 0x000003ff
> +
> +/* Broadcom Thermal Zone Device Structure */
> +struct bcm_thermal_zone_priv {
> + char name[THERMAL_NAME_LENGTH];
> + void __iomem *base;
> +};
> +
> +/* Temperature conversion function for TMON block */
> +static long raw_to_mcelsius(u32 raw)
> +{
> + /*
> + * According to Broadcom internal Analog Module Specification
> + * the formula for converting TMON block output to temperature in
> + * degree Celsius is:
> + * T = 428 - (0.561 * raw)
> + * Note: the valid operating range for the TMON block is -40C to 125C
> + */
> + return 428000 - (561 * (long)raw);
> +}
> +
> +/* Get temperature callback function for thermal zone */
> +static int bcm_get_temp(struct thermal_zone_device *thermal,
> + unsigned long *temp)
> +{
> + u32 raw;
> + long mcelsius;
> + struct bcm_thermal_zone_priv *priv = thermal->devdata;
> +
> + if (!priv) {
> + pr_err("%s: thermal zone number %d devdata not initialized.\n",
> + __func__, thermal->id);
> + return -EINVAL;
> + }
> +
> + raw = (readl(priv->base + TMON_TEMP_VAL_OFFSET)
> + & TMON_TEMP_VAL_TEMP_VAL_MASK) >> TMON_TEMP_VAL_TEMP_VAL_SHIFT;
> +
> + pr_debug("%s: thermal zone number %d raw temp 0x%x\n", __func__,
> + thermal->id, raw);
> +
> + mcelsius = raw_to_mcelsius(raw);
> +
> + /*
> + * Since 'mcelsius' might be negative, we need to limit it to smallest
> + * unsigned value before returning it to thermal framework.
> + */
> + if (mcelsius < 0)
> + *temp = 0;
> + else
> + *temp = mcelsius;
> +
> + pr_debug("%s: thermal zone number %d final temp %d\n", __func__,
> + thermal->id, (int) *temp);
> +
> + return 0;
> +}
> +
> +/* Operation callback functions for thermal zone */
> +static struct thermal_zone_device_ops bcm_dev_ops = {
> + .get_temp = bcm_get_temp,
> +};
> +
> +static const struct of_device_id bcm_tmu_match_table[] = {
> + { .compatible = "brcm,kona-thermal" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, bcm_tmu_match_table);
> +
> +static int bcm_tmu_probe(struct platform_device *pdev)
> +{
> + struct thermal_zone_device *thermal = NULL;
> + struct bcm_thermal_zone_priv *priv;
> + struct resource *res;
> + const char *str;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv) {
> + dev_err(&pdev->dev, "Failed to malloc priv.\n");
> + return -ENOMEM;
> + }
> +
> + /* Obtain the tmu name from device tree file */
> + if (of_property_read_string(pdev->dev.of_node, "thermal-name",

Hello Wendy,

I would prefer we wait until the work for thermal data [1] gets accepted
before accepting this driver, specially because you are adding device
specific DT entry to help in your registration with the thermal
framework. With the mentioned work you wont need it at all.

All best,

[1] - http://lkml.org/lkml/2013/9/15/122

> + &str) == 0) {
> + strlcpy(priv->name, str, sizeof(priv->name));
> + } else {
> + dev_err(&pdev->dev, "Failed to get thermal-name from DT.\n");
> + return -EINVAL;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + thermal = thermal_zone_device_register(priv->name, 0, 0, priv,
> + &bcm_dev_ops, NULL, 0, 0);
> + if (IS_ERR(thermal)) {
> + dev_err(&pdev->dev,
> + "Failed to register Broadcom thermal zone device.\n");
> + return PTR_ERR(thermal);
> + }
> +
> + platform_set_drvdata(pdev, thermal);
> +
> + dev_info(&pdev->dev, "Broadcom Thermal Monitor Initialized.\n");
> +
> + return 0;
> +}
> +
> +static int bcm_tmu_remove(struct platform_device *pdev)
> +{
> + struct thermal_zone_device *broadcom_thermal =
> + platform_get_drvdata(pdev);
> +
> + thermal_zone_device_unregister(broadcom_thermal);
> +
> + dev_info(&pdev->dev, "Broadcom Thermal Monitor Uninitialized.\n");
> +
> + return 0;
> +}
> +
> +static struct platform_driver bcm_tmu_driver = {
> + .driver = {
> + .name = "bcm-thermal",
> + .owner = THIS_MODULE,
> + .of_match_table = bcm_tmu_match_table,
> + },
> + .probe = bcm_tmu_probe,
> + .remove = bcm_tmu_remove,
> +};
> +
> +module_platform_driver(bcm_tmu_driver);
> +
> +MODULE_DESCRIPTION("Broadcom Thermal Driver");
> +MODULE_AUTHOR("Broadcom");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:bcm-thermal");
>


--
You have got to be excited about what you are doing. (L. Lamport)

Eduardo Valentin

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-09-23 22:41    [W:0.083 / U:0.988 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site