lkml.org 
[lkml]   [2013]   [Aug]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC 2/2] usb: dwc3: Add Qualcomm DWC3 glue layer driver
From
Date
Hi, 

On Fri, 2013-08-09 at 16:23 +0300, Felipe Balbi wrote:
> Hi,
>
> On Tue, Aug 06, 2013 at 02:53:11PM +0300, Ivan T. Ivanov wrote:
> > diff --git a/drivers/usb/dwc3/dwc3-msm.c b/drivers/usb/dwc3/dwc3-msm.c
> > new file mode 100644
> > index 0000000..e509abc
> > --- /dev/null
> > +++ b/drivers/usb/dwc3/dwc3-msm.c
> > @@ -0,0 +1,175 @@
> > +#undef CONFIG_REGULATOR
>
> why ??????
>

1. This shows that driver is still not fully tested
Regulators support is still missing in the MSM
2. Helps me to load driver successfully.

> > +static int dwc3_msm_probe(struct platform_device *pdev)
> > +{
> > + struct device_node *node = pdev->dev.of_node;
> > + struct dwc3_msm *mdwc;
> > + struct resource *res;
> > + void __iomem *tcsr;
> > + int ret = 0;
> > +
> > + dev_info(&pdev->dev, "MSM DWC3\n");
>
> please don't. This is hardly necessary.

Sure, this will be removed.

>
> > + mdwc = devm_kzalloc(&pdev->dev, sizeof(*mdwc), GFP_KERNEL);
> > + if (!mdwc) {
> > + dev_err(&pdev->dev, "not enough memory\n");
>
> this message isn't needed either

ok.

>
> > + /*
> > + * DWC3 Core requires its CORE CLK (aka master / bus clk) to
> > + * run at 125Mhz in SSUSB mode and >60MHZ for HSUSB mode.
> > + */
> > + clk_set_rate(mdwc->core_clk, 125000000);
>
> if this is dwc3's core clock, why don't we teach dwc3.ko about this
> requirement ? Just make sure to have it optional, since x86 and OMAP
> wouldn't need direct fiddling with the clocks.

I have to check whether DWC3 core or Qcom wrapper requires this clock.

>
> > + clk_prepare_enable(mdwc->core_clk);
> > + clk_prepare_enable(mdwc->iface_clk);
> > + clk_prepare_enable(mdwc->sleep_clk);
> > + clk_prepare_enable(mdwc->utmi_clk);
>
> do you really need to enable your clocks here ? Why don't you enable
> them on runtime_resume and disable on runtime_suspend ?

I will like to make it working first and then will improve
power management.

>
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + tcsr = devm_ioremap_resource(&pdev->dev, res);
> > + if (!tcsr) {
> > + dev_dbg(&pdev->dev, "tcsr ioremap failed\n");
>
> no need to ioremap, also you're likely leaking clocks and regulators
> enabled here.
>
> Make sure to have something like:
>
> if (!tcsr)
> goto err_disable_clocks;
>
> /* TODO This has to be revised */\
>
> [...]
>

Sure.

> > + } else {
> > + /* TODO: This has to be revised */
> > +
> > + /* Enable USB3 on the primary USB port. */
> > + writel_relaxed(0x1, tcsr);
> > + /*
> > + * Ensure that TCSR write is completed before
> > + * USB registers initialization.
> > + */
> > + mb();
>
> why don't you use writel() instead. It will add the memory barrier for
> you.

Ok.

Thanks
Ivan




\
 
 \ /
  Last update: 2013-08-09 19:01    [W:0.170 / U:0.384 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site