lkml.org 
[lkml]   [2013]   [Aug]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH RFC v3] mmc: sdhci-msm: Add support for MSM chipsets
From
Date
Hi Georgi, 

On Tue, 2013-08-20 at 19:44 +0300, Georgi Djakov wrote:
> This platform driver adds the support of Secure Digital Host
> Controller Interface compliant controller in MSM chipsets.
>
> CC: Asutosh Das <asutoshd@codeaurora.org>
> CC: Venkat Gopalakrishnan <venkatg@codeaurora.org>
> CC: Sahitya Tummala <stummala@codeaurora.org>
> CC: Subhash Jadavani <subhashj@codeaurora.org>
> Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
> ---
> Changes from v2:
> - Added DT bindings for clocks
> - Moved voltage regulators data to platform data
> - Removed unneeded includes
> - Removed obsolete and wrapper functions
> - Removed error checking where unnecessary
> - Removed redundant _clk suffix from clock names
> - Just return instead of goto where possible
> - Minor fixes
>

Is this version intermediate step before you address
all previous comments?

<snip>

> +
> +static const struct of_device_id sdhci_msm_dt_match[] = {
> + {.compatible = "qcom,sdhci-msm"},

Missing termination entry

> +};
> +
> +MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);
> +
> +static int sdhci_msm_probe(struct platform_device *pdev)
> +{
> + struct sdhci_host *host;
> + struct sdhci_pltfm_host *pltfm_host;
> + struct sdhci_msm_host *msm_host;
> + struct resource *core_memres = NULL;
> + int ret = 0, dead = 0;
> + struct pinctrl *pinctrl;
> +
> + msm_host = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_msm_host),
> + GFP_KERNEL);
> + if (!msm_host)
> + return -ENOMEM;
> +
> + host = sdhci_pltfm_init(pdev, &msm_host->sdhci_msm_pdata, 0);
> + if (IS_ERR(host)) {
> + dev_err(mmc_dev(host->mmc), "sdhci_pltfm_init error\n");
> + return PTR_ERR(host);
> + }
> +
> + pltfm_host = sdhci_priv(host);
> + pltfm_host->priv = msm_host;
> + msm_host->mmc = host->mmc;
> + msm_host->pdev = pdev;
> +
> + ret = mmc_of_parse(host->mmc);
> + if (ret)

Shouldn't sdhci_pltfm_init operation be reverted?

> + return ret;
> +
> + /* Extract platform data */
> + if (pdev->dev.of_node) {
> + msm_host->pdata = sdhci_msm_populate_pdata(&pdev->dev);
> + if (!msm_host->pdata) {
> + dev_err(&pdev->dev, "DT parsing error\n");
> + goto pltfm_free;
> + }
> + } else {
> + dev_err(&pdev->dev, "No device tree node\n");
> + goto pltfm_free;
> + }
> +
> + /* Setup pins */
> + pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
> + if (IS_ERR(pinctrl))
> + dev_warn(&pdev->dev, "pins are not configured by the driver\n");
> +
> + /* Setup Clocks */
> +
> + /* Setup SDCC bus voter clock. */
> + msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
> + if (!IS_ERR_OR_NULL(msm_host->bus_clk)) {
> + /* Vote for max. clk rate for max. performance */
> + ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
> + if (ret)
> + goto pltfm_free;
> + ret = clk_prepare_enable(msm_host->bus_clk);
> + if (ret)
> + goto pltfm_free;
> + }
> +
> + /* Setup main peripheral bus clock */
> + msm_host->pclk = devm_clk_get(&pdev->dev, "iface");
> + if (!IS_ERR(msm_host->pclk)) {
> + ret = clk_prepare_enable(msm_host->pclk);
> + if (ret) {
> + dev_err(&pdev->dev,
> + "Main peripheral clock setup failed (%d)\n",
> + ret);
> + goto bus_clk_disable;
> + }
> + }
> +
> + /* Setup SDC MMC clock */
> + msm_host->clk = devm_clk_get(&pdev->dev, "core");
> + if (IS_ERR(msm_host->clk)) {
> + ret = PTR_ERR(msm_host->clk);
> + dev_err(&pdev->dev, "SDC MMC clock setup failed (%d)\n", ret);
> + goto pclk_disable;
> + }
> +
> + ret = clk_prepare_enable(msm_host->clk);
> + if (ret)
> + goto pclk_disable;
> +
> + /* Setup regulators */
> + ret = sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, true);
> + if (ret) {
> + dev_err(&pdev->dev, "Regulator setup failed (%d)\n", ret);
> + goto clk_disable;
> + }
> +
> + /* Reset the core and Enable SDHC mode */
> + core_memres = platform_get_resource_byname(pdev,
> + IORESOURCE_MEM, "core_mem");
> + msm_host->core_mem = devm_ioremap(&pdev->dev, core_memres->start,
> + resource_size(core_memres));
> +
> + if (!msm_host->core_mem) {
> + dev_err(&pdev->dev, "Failed to remap registers\n");
> + ret = -ENOMEM;
> + goto vreg_deinit;
> + }
> +
> + /* Set SW_RST bit in POWER register (Offset 0x0) */
> + writel_relaxed(CORE_SW_RST, msm_host->core_mem + CORE_POWER);
> + /* Set HC_MODE_EN bit in HC_MODE register */
> + writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
> +
> + /*
> + * Following are the deviations from SDHC spec v3.0 -
> + * 1. Card detection is handled using separate GPIO.
> + * 2. Bus power control is handled by interacting with PMIC.
> + */
> + host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
> +
> + /* Setup PWRCTL irq */
> + msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
> + if (msm_host->pwr_irq < 0) {
> + dev_err(&pdev->dev, "Failed to get pwr_irq by name (%d)\n",
> + msm_host->pwr_irq);
> + goto vreg_deinit;
> + }
> + ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL,
> + sdhci_msm_pwr_irq, IRQF_ONESHOT,
> + dev_name(&pdev->dev), host);
> + if (ret) {
> + dev_err(&pdev->dev, "Request threaded irq(%d) failed (%d)\n",
> + msm_host->pwr_irq, ret);
> + goto vreg_deinit;
> + }
> +
> + /* Enable pwr irq interrupts */
> + writel_relaxed(INT_MASK, (msm_host->core_mem + CORE_PWRCTL_MASK));
> +
> + /* Set host capabilities */
> + msm_host->mmc->caps |= msm_host->pdata->caps;
> + msm_host->mmc->caps2 |= msm_host->pdata->caps2;
> +
> + ret = sdhci_add_host(host);
> + if (ret) {
> + dev_err(&pdev->dev, "Add host failed (%d)\n", ret);
> + goto vreg_deinit;
> + }
> +
> + /* Set core clk rate */
> + ret = clk_set_rate(msm_host->clk, host->max_clk);
> + if (ret) {
> + dev_err(&pdev->dev, "MClk rate set failed (%d)\n", ret);
> + goto remove_host;
> + }
> +
> + host->mmc->max_current_180 = host->mmc->max_current_300 =
> + host->mmc->max_current_330 = sdhci_msm_get_vdd_max_current(msm_host);
> +
> + /* Successful initialization */
> + goto out;
> +
> +remove_host:
> + dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff);
> + sdhci_remove_host(host, dead);
> +vreg_deinit:
> + sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, false);
> +clk_disable:
> + if (!IS_ERR(msm_host->clk))
> + clk_disable_unprepare(msm_host->clk);
> +pclk_disable:
> + if (!IS_ERR(msm_host->pclk))
> + clk_disable_unprepare(msm_host->pclk);
> +bus_clk_disable:
> + if (!IS_ERR_OR_NULL(msm_host->bus_clk))
> + clk_disable_unprepare(msm_host->bus_clk);
> +pltfm_free:
> + sdhci_pltfm_free(pdev);
> +out:
> + return ret;
> +}
> +

<snip>

> +
> +static struct platform_driver sdhci_msm_driver = {
> + .probe = sdhci_msm_probe,
> + .remove = sdhci_msm_remove,
> + .driver = {
> + .name = "sdhci_msm",
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(sdhci_msm_dt_match),

of_match_ptr is not really required.

Regards,
Ivan

> + },
> +};
> +
> +module_platform_driver(sdhci_msm_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver");
> +MODULE_LICENSE("GPL v2");




\
 
 \ /
  Last update: 2013-08-23 10:01    [W:0.102 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site