lkml.org 
[lkml]   [2013]   [Aug]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH tip/core/rcu 2/9] nohz_full: Add testing information to documentation
Date
From: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>

This commit adds information about testing nohz_full, and also emphasizes
the fact that you need a multi-CPU system to get any benefit from nohz_full.

Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
---
Documentation/timers/NO_HZ.txt | 44 ++++++++++++++++++++++++++++++++----------
1 file changed, 34 insertions(+), 10 deletions(-)

diff --git a/Documentation/timers/NO_HZ.txt b/Documentation/timers/NO_HZ.txt
index 8869758..cca122f 100644
--- a/Documentation/timers/NO_HZ.txt
+++ b/Documentation/timers/NO_HZ.txt
@@ -24,8 +24,8 @@ There are three main ways of managing scheduling-clock interrupts
workloads, you will normally -not- want this option.

These three cases are described in the following three sections, followed
-by a third section on RCU-specific considerations and a fourth and final
-section listing known issues.
+by a third section on RCU-specific considerations, a fourth section
+discussing testing, and a fifth and final section listing known issues.


NEVER OMIT SCHEDULING-CLOCK TICKS
@@ -121,14 +121,15 @@ boot parameter specifies the adaptive-ticks CPUs. For example,
"nohz_full=1,6-8" says that CPUs 1, 6, 7, and 8 are to be adaptive-ticks
CPUs. Note that you are prohibited from marking all of the CPUs as
adaptive-tick CPUs: At least one non-adaptive-tick CPU must remain
-online to handle timekeeping tasks in order to ensure that system calls
-like gettimeofday() returns accurate values on adaptive-tick CPUs.
-(This is not an issue for CONFIG_NO_HZ_IDLE=y because there are no
-running user processes to observe slight drifts in clock rate.)
-Therefore, the boot CPU is prohibited from entering adaptive-ticks
-mode. Specifying a "nohz_full=" mask that includes the boot CPU will
-result in a boot-time error message, and the boot CPU will be removed
-from the mask.
+online to handle timekeeping tasks in order to ensure that system
+calls like gettimeofday() returns accurate values on adaptive-tick CPUs.
+(This is not an issue for CONFIG_NO_HZ_IDLE=y because there are no running
+user processes to observe slight drifts in clock rate.) Therefore, the
+boot CPU is prohibited from entering adaptive-ticks mode. Specifying a
+"nohz_full=" mask that includes the boot CPU will result in a boot-time
+error message, and the boot CPU will be removed from the mask. Note that
+this means that your system must have at least two CPUs in order for
+CONFIG_NO_HZ_FULL=y to do anything for you.

Alternatively, the CONFIG_NO_HZ_FULL_ALL=y Kconfig parameter specifies
that all CPUs other than the boot CPU are adaptive-ticks CPUs. This
@@ -232,6 +233,29 @@ scheduler will decide where to run them, which might or might not be
where you want them to run.


+TESTING
+
+So you enable all the OS-jitter features described in this document,
+but do not see any change in your workload's behavior. Is this because
+your workload isn't affected that much by OS jitter, or is it because
+something else is in the way? This section helps answer this question
+by providing a simple OS-jitter test suite, which is available on branch
+master of the following git archive:
+
+git://git.kernel.org/pub/scm/linux/kernel/git/frederic/dynticks-testing.git
+
+Clone this archive and follow the instructions in the README file.
+This test procedure will produce a trace that will allow you to evaluate
+whether or not you have succeeded in removing OS jitter from your system.
+If this trace shows that you have removed OS jitter as much as is
+possible, then you can conclude that your workload is not all that
+sensitive to OS jitter.
+
+Note: this test requires that your system have at least two CPUs.
+We do not currently have a good way to remove OS jitter from single-CPU
+systems.
+
+
KNOWN ISSUES

o Dyntick-idle slows transitions to and from idle slightly.
--
1.8.1.5


\
 
 \ /
  Last update: 2013-08-18 04:21    [W:0.076 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site