lkml.org 
[lkml]   [2013]   [Jul]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] pinctrl: msm: Add support for MSM TLMM pinmux
On 07/31/2013 01:46 PM, Hanumant Singh wrote:
> On 7/30/2013 8:59 PM, Stephen Warren wrote:
>> On 07/30/2013 06:13 PM, Hanumant Singh wrote:
>>> On 7/30/2013 5:08 PM, Stephen Warren wrote:
>>>> On 07/30/2013 06:01 PM, Hanumant Singh wrote:
>>>>> On 7/30/2013 2:22 PM, Stephen Warren wrote:
>>>>>> On 07/30/2013 03:10 PM, hanumant wrote:
>>>>>> ...
>>>>>>> We actually have the same TLMM pinmux used by several socs of a
>>>>>>> family.
>>>>>>> The number of pins on each soc may vary.
>>>>>>> Also a given soc gets used in a number of boards.
>>>>>>> The device tree for a given soc is split into the different boards
>>>>>>> that
>>>>>>> its in ie the boards inherit a common soc.dtsi but have separate
>>>>>>> dts.
>>>>>>> The boards for the same soc may use different pin groups for
>>>>>>> accomplishing a function, since we have multiple i2c, spi uart etc
>>>>>>> peripheral instances on a soc. A different instance of each of the
>>>>>>> above
>>>>>>> peripherals, can be used in different boards, utilizing different
>>>>>>> or subset of same pin groups.
>>>>>>> Thus I would need to have multiple C files for one soc, based on the
>>>>>>> boards that it goes into.
>>>>>>
>>>>>> The pinctrl driver should be exposing the raw capabilities of the HW.
>>>>>> All the board-specific configuration should be expressed in DT.
>>>>>> So, the
>>>>>> driver shouldn't have to know anything about different boards at
>>>>>> compile-time.
>>>>>>
>>>>> I agree, so I wanted to keep the pin grouping information in DT, we
>>>>> already have a board based differentiation of dts files in DT, for the
>>>>> same soc.
>>>>
>>>> That's the opposite of what I was saying. Pin groups are a feature of
>>>> the SoC design, not the board.
>>>>
>>> Sorry I guess I wasn't clear.
>>> Right now I have a soc-pinctrl.dtsi containing pin groupings.
>>> This will be "inherited" by soc-boardtype.dts.
>>> The pinctrl client device nodes in soc-boardtype.dts will point to pin
>>> groupings in soc-pinctrl.dtsi that are valid for that particular
>>> boardtype.
>>> Is this a valid design?
>>
>> OK, so you have two types of child node inside the pinctrl DT node; some
>> define the pin groups the SoC has (in soc.dtsi) and some define pinctrl
>> states that reference the pin group nodes and are referenced by the
>> client nodes.
>>
>> That's probably fine. However, I'd still question putting the pin group
>> nodes in DT at all; I'm not convinced it's better than just putting
>> those into the driver itself. You end up with the same data tables after
>> parsing the DT anyway.
>>
>
> Any feedback for the rest of the patch?

I'm certainly waiting for this aspect of the patch to be resolved; I
think it will impact the rest of the patch so much that it's not worth
reviewing until we decide on where to represent the pin groups (some DT
parsing could would be removed if we put the pin group definitions into
the driver, hence wouldn't need to be reviewed, and likewise there's be
some new tables to review).


\
 
 \ /
  Last update: 2013-07-31 23:21    [W:0.114 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site