lkml.org 
[lkml]   [2013]   [Jul]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCHv4 2/3] drivers: spi: Add qspi flash controller
On Thu, Jul 18, 2013 at 04:48:41PM +0530, Sourav Poddar wrote:
> >>+static void qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t)
> >>+{
> >>+ const u8 *txbuf;
> >>+ int wlen, count;
> >>+
> >>+ count = t->len;
> >>+ txbuf = t->tx_buf;
> >>+ wlen = t->bits_per_word;
> >>+
> >>+ while (count--) {
> >>+ dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n",
> >>+ qspi->cmd | QSPI_WR_SNGL, qspi->dc, *txbuf);
> >>+ ti_qspi_writel_data(qspi, *txbuf++, QSPI_SPI_DATA_REG, wlen);
> >you always increment by each byte. Here, if you used writel(), you wrote
> >4 bytes and should increment txbuf by 4.
>
> hmm..got this point. Yes, my mistake, here I agree if wlen is not 8 bits
> txbuf++ is not valid.
> > Same goes for read_data(),
> >below. Another thing. Even though your wlen might be 8 bits, if you
> >write 4 bytes to write, you can save a few CPU cycles by using writel().
> >
> Do you mean 4 words of 8 bits?

yeah. Say you have wlen = 8 but the transfer length is 8 bytes (64
bits). If you use writeb(), you will do 8 writes, if you use writel()
you'll do 2 writes.

> >>+static int ti_qspi_start_transfer_one(struct spi_master *master,
> >>+ struct spi_message *m)
> >>+{
> >>+ struct ti_qspi *qspi = spi_master_get_devdata(master);
> >>+ struct spi_device *spi = m->spi;
> >>+ struct spi_transfer *t;
> >>+ int status = 0, ret;
> >>+ int frame_length;
> >>+
> >>+ /* setup device control reg */
> >>+ qspi->dc = 0;
> >>+
> >>+ if (spi->mode& SPI_CPHA)
> >>+ qspi->dc |= QSPI_CKPHA(spi->chip_select);
> >>+ if (spi->mode& SPI_CPOL)
> >>+ qspi->dc |= QSPI_CKPOL(spi->chip_select);
> >>+ if (spi->mode& SPI_CS_HIGH)
> >>+ qspi->dc |= QSPI_CSPOL(spi->chip_select);
> >>+
> >>+ frame_length = DIV_ROUND_UP(m->frame_length * spi->bits_per_word,
> >>+ spi->bits_per_word);
> >this calculation doesn't look correct.
> >
> > (m->frame_length * spi->bits_per_word) /
> > spi->bits_per_word = m->frame_length
> >
> >What are you trying to achieve here ? frame_length should be counted in
> >words right ? And we get that value in bytes. So what's the best
> >calculation to convert bytes into words ? If you have 8 bits_per_word
> >you don't need any calculation, but if you have 32 bits_per_word, you
> >_do_ need something.
> >
> Yes, just derive this formulae with 8 bits per word in mind.
> Will change.
> It should be (m->frame_length * 8) / spi->bits_per_word

right on. To make sure this will execute a little faster (you never know
what several different versions of GCC will do), instead of multiplying
by 8, left shift by 3.

> >How will you achieve the number you want ? (hint: 1 byte == 8 bits)
> >
> >And btw, all of these mistakes pretty much tell me that this driver
> >hasn't been tested. How have you tested this driver ?
> After bootup, I checked for deive detting enumerated as /proc/mtd.
> After which I am using mtdutils(erase, dump and write utilied to
> check for the communication with the flash device.)

alright, make that clear in your commit log.

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-07-18 14:21    [W:1.631 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site