lkml.org 
[lkml]   [2013]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 6/6] DT: Add documentation for gpio-xilinx
Date
Describe gpio-xilinx binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v2:
- Extend description

.../devicetree/bindings/gpio/gpio-xilinx.txt | 48 ++++++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/gpio/gpio-xilinx.txt

diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
new file mode 100644
index 0000000..63bf4be
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt
@@ -0,0 +1,48 @@
+Xilinx plb/axi GPIO controller
+
+Dual channel GPIO controller with configurable number of pins
+(from 1 to 32 per channel). Every pin can be configured as
+input/output/tristate. Both channels share the same global IRQ but
+local interrupts can be enabled on channel basis.
+
+Required properties:
+- compatible : Should be "xlnx,xps-gpio-1.00.a"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters (currently unused).
+- gpio-controller : Marks the device node as a GPIO controller.
+
+Optional properties:
+- interrupts : Interrupt mapping for GPIO IRQ.
+- interrupt-parent : Phandle for the interrupt controller that
+ services interrupts for this device.
+- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
+- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
+- xlnx,gpio-width : gpio width
+- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
+- xlnx,is-dual : if 1, controller also uses the second channel
+- xlnx,all-inputs-2 : as above but for the second channel
+- xlnx,dout-default-2 : as above but the second channel
+- xlnx,gpio2-width : as above but for the second channel
+- xlnx,tri-default-2 : as above but for the second channel
+
+
+Example:
+gpio: gpio@40000000 {
+ #gpio-cells = <2>;
+ compatible = "xlnx,xps-gpio-1.00.a";
+ gpio-controller ;
+ interrupt-parent = <&microblaze_0_intc>;
+ interrupts = < 6 2 >;
+ reg = < 0x40000000 0x10000 >;
+ xlnx,all-inputs = <0x0>;
+ xlnx,all-inputs-2 = <0x0>;
+ xlnx,dout-default = <0x0>;
+ xlnx,dout-default-2 = <0x0>;
+ xlnx,gpio-width = <0x2>;
+ xlnx,gpio2-width = <0x2>;
+ xlnx,interrupt-present = <0x1>;
+ xlnx,is-dual = <0x1>;
+ xlnx,tri-default = <0xffffffff>;
+ xlnx,tri-default-2 = <0xffffffff>;
+} ;
--
1.8.2.3
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-06-03 15:21    [W:0.094 / U:0.544 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site