lkml.org 
[lkml]   [2013]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 2/7] video: xilinxfb: Do not name out_be32 in function name
Date
out_be32 IO function is not supported by ARM.
It is only available for PPC and Microblaze.
Because this driver can be used on ARM let's
remove out_be32 from function name.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
Changes in v4: None
Changes in v3:
- Remove out_be IO name from function name
- Change patch subject from "Do not use out_be32 IO function"
to "Do not name out_be32 in function name"

Changes in v2: None

drivers/video/xilinxfb.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/drivers/video/xilinxfb.c b/drivers/video/xilinxfb.c
index aecd15d..c9b442b 100644
--- a/drivers/video/xilinxfb.c
+++ b/drivers/video/xilinxfb.c
@@ -57,7 +57,7 @@
* In case of direct PLB access the second control register will be at
* an offset of 4 as compared to the DCR access where the offset is 1
* i.e. REG_CTRL. So this is taken care in the function
- * xilinx_fb_out_be32 where it left shifts the offset 2 times in case of
+ * xilinx_fb_out32 where it left shifts the offset 2 times in case of
* direct PLB access.
*/
#define NUM_REGS 2
@@ -150,7 +150,7 @@ struct xilinxfb_drvdata {
* To perform the read/write on the registers we need to check on
* which bus its connected and call the appropriate write API.
*/
-static void xilinx_fb_out_be32(struct xilinxfb_drvdata *drvdata, u32 offset,
+static void xilinx_fb_out32(struct xilinxfb_drvdata *drvdata, u32 offset,
u32 val)
{
if (drvdata->flags & PLB_ACCESS_FLAG)
@@ -197,7 +197,7 @@ xilinx_fb_blank(int blank_mode, struct fb_info *fbi)
switch (blank_mode) {
case FB_BLANK_UNBLANK:
/* turn on panel */
- xilinx_fb_out_be32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
+ xilinx_fb_out32(drvdata, REG_CTRL, drvdata->reg_ctrl_default);
break;

case FB_BLANK_NORMAL:
@@ -205,7 +205,7 @@ xilinx_fb_blank(int blank_mode, struct fb_info *fbi)
case FB_BLANK_HSYNC_SUSPEND:
case FB_BLANK_POWERDOWN:
/* turn off panel */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);
default:
break;

@@ -280,13 +280,13 @@ static int xilinxfb_assign(struct device *dev,
memset_io((void __iomem *)drvdata->fb_virt, 0, fbsize);

/* Tell the hardware where the frame buffer is */
- xilinx_fb_out_be32(drvdata, REG_FB_ADDR, drvdata->fb_phys);
+ xilinx_fb_out32(drvdata, REG_FB_ADDR, drvdata->fb_phys);

/* Turn on the display */
drvdata->reg_ctrl_default = REG_CTRL_ENABLE;
if (pdata->rotate_screen)
drvdata->reg_ctrl_default |= REG_CTRL_ROTATE;
- xilinx_fb_out_be32(drvdata, REG_CTRL,
+ xilinx_fb_out32(drvdata, REG_CTRL,
drvdata->reg_ctrl_default);

/* Fill struct fb_info */
@@ -345,7 +345,7 @@ err_cmap:
iounmap(drvdata->fb_virt);

/* Turn off the display */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);

err_fbmem:
if (drvdata->flags & PLB_ACCESS_FLAG)
@@ -381,7 +381,7 @@ static int xilinxfb_release(struct device *dev)
iounmap(drvdata->fb_virt);

/* Turn off the display */
- xilinx_fb_out_be32(drvdata, REG_CTRL, 0);
+ xilinx_fb_out32(drvdata, REG_CTRL, 0);

/* Release the resources, as allocated based on interface */
if (drvdata->flags & PLB_ACCESS_FLAG) {
--
1.8.2.3
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-06-03 13:01    [W:0.120 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site