lkml.org 
[lkml]   [2013]   [May]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 04/10] usb: phy: ab8500-usb: restart phy during probe
Date
From: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>

Add an ab8500_usb_restart_phy() function called during probe to ensure
that the AB8500 USB phy is initialized properly even when a cable is
connected at probe time.

Without this fix subsequent host reconnections are not detected
properly.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
---
drivers/usb/phy/phy-ab8500-usb.c | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)

diff --git a/drivers/usb/phy/phy-ab8500-usb.c b/drivers/usb/phy/phy-ab8500-usb.c
index cc0d7e5..bbe51cc 100644
--- a/drivers/usb/phy/phy-ab8500-usb.c
+++ b/drivers/usb/phy/phy-ab8500-usb.c
@@ -668,6 +668,33 @@ static int ab8500_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
return 0;
}

+static void ab8500_usb_restart_phy(struct ab8500_usb *ab)
+{
+ abx500_mask_and_set_register_interruptible(ab->dev,
+ AB8500_USB, AB8500_USB_PHY_CTRL_REG,
+ AB8500_BIT_PHY_CTRL_DEVICE_EN,
+ AB8500_BIT_PHY_CTRL_DEVICE_EN);
+
+ udelay(100);
+
+ abx500_mask_and_set_register_interruptible(ab->dev,
+ AB8500_USB, AB8500_USB_PHY_CTRL_REG,
+ AB8500_BIT_PHY_CTRL_DEVICE_EN,
+ 0);
+
+ abx500_mask_and_set_register_interruptible(ab->dev,
+ AB8500_USB, AB8500_USB_PHY_CTRL_REG,
+ AB8500_BIT_PHY_CTRL_HOST_EN,
+ AB8500_BIT_PHY_CTRL_HOST_EN);
+
+ udelay(100);
+
+ abx500_mask_and_set_register_interruptible(ab->dev,
+ AB8500_USB, AB8500_USB_PHY_CTRL_REG,
+ AB8500_BIT_PHY_CTRL_HOST_EN,
+ 0);
+}
+
static int ab8500_usb_regulator_get(struct ab8500_usb *ab)
{
int err;
@@ -887,6 +914,12 @@ static int ab8500_usb_probe(struct platform_device *pdev)
/* Needed to enable ID detection. */
ab8500_usb_wd_workaround(ab);

+ /*
+ * This is required for usb-link-status to work properly when a
+ * cable is connected at boot time.
+ */
+ ab8500_usb_restart_phy(ab);
+
abx500_usb_link_status_update(ab);

dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev);
--
1.8.2


\
 
 \ /
  Last update: 2013-05-15 14:41    [W:0.184 / U:0.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site