lkml.org 
[lkml]   [2013]   [Apr]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ARM: bcm281xx: Add L2 support for Rev A2 chips
Date
Rev A2 SoCs have an unorthodox memory re-mapping and this needs
to be reflected in the cache operations.
This patch adds new outer cache functions for the l2x0 driver
to support this SoC revision. It also adds a new compatible
value for the cache to enable this functionality.

Signed-off-by: Christian Daudt <csd@broadcom.com>

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
index cbef09b..69ddf9f 100644
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -16,6 +16,9 @@ Required properties:
performs the same operation).
"marvell,"aurora-outer-cache: Marvell Controller designed to be
compatible with the ARM one with outer cache mode.
+ "bcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
+ offset needs to be added to the address before passing down to the L2
+ cache controller
- cache-unified : Specifies the cache is a unified cache.
- cache-level : Should be set to 2 for a level 2 cache.
- reg : Physical base address and size of cache controller's memory mapped
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 41b2c6c..5e48c85 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -47,10 +47,10 @@
};

L2: l2-cache {
- compatible = "arm,pl310-cache";
- reg = <0x3ff20000 0x1000>;
- cache-unified;
- cache-level = <2>;
+ compatible = "bcm,bcm11351-a2-pl310-cache";
+ reg = <0x3ff20000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
};

timer@35006000 {
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index c465fac..6edba13 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -523,6 +523,162 @@ static void aurora_flush_range(unsigned long start, unsigned long end)
}
}

+/*
+ * For certain Broadcom SoCs, depending on the address range, different offsets
+ * need to be added to the address before passing it to L2 for
+ * invalidation/clean/flush
+ *
+ * Section Address Range Offset EMI
+ * 1 0x00000000 - 0x3FFFFFFF 0x80000000 VC
+ * 2 0x40000000 - 0xBFFFFFFF 0x40000000 SYS
+ * 3 0xC0000000 - 0xFFFFFFFF 0x80000000 VC
+ *
+ * When the start and end addresses have crossed two different sections, we
+ * need to break the L2 operation into two, each within its own section.
+ * For example, if we need to invalidate addresses starts at 0xBFFF0000 and
+ * ends at 0xC0001000, we need do invalidate 1) 0xBFFF0000 - 0xBFFFFFFF and 2)
+ * 0xC0000000 - 0xC0001000
+ *
+ * Note 1:
+ * By breaking a single L2 operation into two, we may potentially suffer some
+ * performance hit, but keep in mind the cross section case is very rare
+ *
+ * Note 2:
+ * We do not need to handle the case when the start address is in
+ * Section 1 and the end address is in Section 3, since it is not a valid use
+ * case
+ */
+
+#define BCM_VC_EMI_SEC1_START_ADDR 0x00000000UL
+#define BCM_VC_EMI_SEC1_END_ADDR 0x3FFFFFFFUL
+#define BCM_SYS_EMI_START_ADDR 0x40000000UL
+#define BCM_SYS_EMI_END_ADDR 0xBFFFFFFFUL
+#define BCM_VC_EMI_SEC3_START_ADDR 0xC0000000UL
+#define BCM_VC_EMI_SEC3_END_ADDR 0xFFFFFFFFUL
+
+#define BCM_SYS_EMI_OFFSET 0x40000000UL
+#define BCM_VC_EMI_OFFSET 0x80000000UL
+
+static inline int bcm_addr_is_sys_emi(unsigned long addr)
+{
+ return (addr >= BCM_SYS_EMI_START_ADDR) &&
+ (addr <= BCM_SYS_EMI_END_ADDR);
+}
+
+static inline unsigned long bcm_l2_phys_addr(unsigned long addr)
+{
+ if (bcm_addr_is_sys_emi(addr))
+ return addr + BCM_SYS_EMI_OFFSET;
+ else
+ return addr + BCM_VC_EMI_OFFSET;
+}
+
+static void bcm_inv_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ if (unlikely(end <= start))
+ return;
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely((bcm_addr_is_sys_emi(start) && bcm_addr_is_sys_emi(end)) ||
+ (!bcm_addr_is_sys_emi(start) && !bcm_addr_is_sys_emi(end)))) {
+ l2x0_inv_range(new_start, new_end);
+ return;
+ }
+
+ if (bcm_addr_is_sys_emi(start)) {
+ /* start address in Section 2. end address in Section 3 */
+ l2x0_inv_range(new_start,
+ bcm_l2_phys_addr(BCM_SYS_EMI_END_ADDR));
+ l2x0_inv_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+ } else {
+ /* start address in Section 1. end address in Section 2 */
+ l2x0_inv_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC1_END_ADDR));
+ l2x0_inv_range(bcm_l2_phys_addr(BCM_SYS_EMI_START_ADDR),
+ new_end);
+ }
+}
+
+static void bcm_clean_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ if (unlikely(end <= start))
+ return;
+
+ if ((end - start) >= l2x0_size) {
+ l2x0_clean_all();
+ return;
+ }
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely((bcm_addr_is_sys_emi(start) && bcm_addr_is_sys_emi(end)) ||
+ (!bcm_addr_is_sys_emi(start) && !bcm_addr_is_sys_emi(end)))) {
+ l2x0_clean_range(new_start, new_end);
+ return;
+ }
+
+ if (bcm_addr_is_sys_emi(start)) {
+ /* start address in Section 2. end address in Section 3 */
+ l2x0_clean_range(new_start,
+ bcm_l2_phys_addr(BCM_SYS_EMI_END_ADDR));
+ l2x0_clean_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+ } else {
+ /* start address in Section 1. end address in Section 2 */
+ l2x0_clean_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC1_END_ADDR));
+ l2x0_clean_range(bcm_l2_phys_addr(BCM_SYS_EMI_START_ADDR),
+ new_end);
+ }
+}
+
+static void bcm_flush_range(unsigned long start, unsigned long end)
+{
+ unsigned long new_start, new_end;
+
+ if (unlikely(end <= start))
+ return;
+
+ if ((end - start) >= l2x0_size) {
+ l2x0_flush_all();
+ return;
+ }
+
+ new_start = bcm_l2_phys_addr(start);
+ new_end = bcm_l2_phys_addr(end);
+
+ /* normal case, no cross section between start and end */
+ if (likely((bcm_addr_is_sys_emi(start) && bcm_addr_is_sys_emi(end)) ||
+ (!bcm_addr_is_sys_emi(start) && !bcm_addr_is_sys_emi(end)))) {
+ l2x0_flush_range(new_start, new_end);
+ return;
+ }
+
+ if (bcm_addr_is_sys_emi(start)) {
+ /* start address in Section 2. end address in Section 3 */
+ l2x0_flush_range(new_start,
+ bcm_l2_phys_addr(BCM_SYS_EMI_END_ADDR));
+ l2x0_flush_range(bcm_l2_phys_addr(BCM_VC_EMI_SEC3_START_ADDR),
+ new_end);
+ } else {
+ /* start address in Section 1. end address in Section 2 */
+ l2x0_flush_range(new_start,
+ bcm_l2_phys_addr(BCM_VC_EMI_SEC1_END_ADDR));
+ l2x0_flush_range(bcm_l2_phys_addr(BCM_SYS_EMI_START_ADDR),
+ new_end);
+ }
+}
+
static void __init l2x0_of_setup(const struct device_node *np,
u32 *aux_val, u32 *aux_mask)
{
@@ -765,6 +921,21 @@ static const struct l2x0_of_data aurora_no_outer_data = {
},
};

+static const struct l2x0_of_data bcm_l2x0_data = {
+ .setup = pl310_of_setup,
+ .save = pl310_save,
+ .outer_cache = {
+ .resume = pl310_resume,
+ .inv_range = bcm_inv_range,
+ .clean_range = bcm_clean_range,
+ .flush_range = bcm_flush_range,
+ .sync = l2x0_cache_sync,
+ .flush_all = l2x0_flush_all,
+ .inv_all = l2x0_inv_all,
+ .disable = l2x0_disable,
+ },
+};
+
static const struct of_device_id l2x0_ids[] __initconst = {
{ .compatible = "arm,pl310-cache", .data = (void *)&pl310_data },
{ .compatible = "arm,l220-cache", .data = (void *)&l2x0_data },
@@ -773,6 +944,8 @@ static const struct of_device_id l2x0_ids[] __initconst = {
.data = (void *)&aurora_no_outer_data},
{ .compatible = "marvell,aurora-outer-cache",
.data = (void *)&aurora_with_outer_data},
+ { .compatible = "bcm,bcm11351-a2-pl310-cache",
+ .data = (void *)&bcm_l2x0_data},
{}
};

--
1.7.10.4



\
 
 \ /
  Last update: 2013-04-30 21:21    [W:0.081 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site