Messages in this thread Patch in this message | | | From | Lee Jones <> | Subject | [PATCH 30/73] regulator: ab8500: Remove Vsafe voltage settings | Date | Mon, 4 Feb 2013 11:53:45 +0000 |
| |
From: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
The Vsafe regulator should not be handled by the kernel, it should be setup before the kernel starts. This patch removes the voltage settings.
Current consumption will increase slightly (rough estimate 25 uA) when the platform is in the low power state because SoC sets a voltage of 0.95 V where the kernel set a voltage of 0.925 V.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> --- arch/arm/mach-ux500/board-mop500-regulators.c | 10 ---------- drivers/regulator/ab8500.c | 10 ---------- include/linux/regulator/ab8500.h | 2 -- 3 files changed, 22 deletions(-)
diff --git a/arch/arm/mach-ux500/board-mop500-regulators.c b/arch/arm/mach-ux500/board-mop500-regulators.c index 8473ee1..f9f3fc3 100644 --- a/arch/arm/mach-ux500/board-mop500-regulators.c +++ b/arch/arm/mach-ux500/board-mop500-regulators.c @@ -265,22 +265,12 @@ static struct ab8500_regulator_reg_init ab8500_reg_init[] = { */ INIT_REGULATOR_REGISTER(AB8500_VSMPS2REGU, 0x0f, 0x06), /* - * Vsmps3Sel2 = 1.2125 V - * NOTE! PRCMU register - */ - INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL2, 0x7f, 0x29), - /* * Vsmps3Regu = HW control * Vsmps3SelCtrl = Vsmps3 voltage defined by Vsmps3Sel2 * NOTE! PRCMU register */ INIT_REGULATOR_REGISTER(AB8500_VSMPS3REGU, 0x0f, 0x06), /* - * Vsmps3Sel1 = 0.9 V - * NOTE! PRCMU register - */ - INIT_REGULATOR_REGISTER(AB8500_VSMPS3SEL1, 0x7f, 0x10), - /* * VPll = Hw controlled * VanaRegu = force off */ diff --git a/drivers/regulator/ab8500.c b/drivers/regulator/ab8500.c index 406c561..3f5db96 100644 --- a/drivers/regulator/ab8500.c +++ b/drivers/regulator/ab8500.c @@ -802,16 +802,6 @@ static struct ab8500_reg_init ab8500_reg_init[] = { */ REG_INIT(AB8500_VSMPS2SEL3, 0x04, 0x19, 0x3f), /* - * 0x7f, Vsmps3Sel1 - * NOTE! PRCMU register - */ - REG_INIT(AB8500_VSMPS3SEL1, 0x04, 0x1b, 0x7f), - /* - * 0x7f, Vsmps3Sel2 - * NOTE! PRCMU register - */ - REG_INIT(AB8500_VSMPS3SEL2, 0x04, 0x1c, 0x7f), - /* * 0x0f, Vaux1Sel */ REG_INIT(AB8500_VAUX1SEL, 0x04, 0x1f, 0x0f), diff --git a/include/linux/regulator/ab8500.h b/include/linux/regulator/ab8500.h index 094d24c..74955db 100644 --- a/include/linux/regulator/ab8500.h +++ b/include/linux/regulator/ab8500.h @@ -93,8 +93,6 @@ enum ab8500_regulator_reg { AB8500_VSMPS2SEL1, AB8500_VSMPS2SEL2, AB8500_VSMPS2SEL3, - AB8500_VSMPS3SEL1, /* NOTE! PRCMU register */ - AB8500_VSMPS3SEL2, /* NOTE! PRCMU register */ AB8500_VAUX1SEL, AB8500_VAUX2SEL, AB8500_VRF1VAUX3SEL, -- 1.7.9.5
| |