lkml.org 
[lkml]   [2013]   [Oct]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 1/4] i2c: busses: i2c-st: Add ST I2C controller
From
Date

On Oct 29, 2013, at 8:19 AM, Maxime Coquelin wrote:

>
> On 10/28/2013 08:25 PM, Kumar Gala wrote:
>> On Oct 14, 2013, at 7:46 AM, Maxime COQUELIN wrote:
>>
>>> This patch adds support to SSC (Synchronous Serial Controller)
>>> I2C driver. This IP also supports SPI protocol, but this is not
>>> the aim of this driver.
>>>
>>> This IP is embedded in all ST SoCs for Set-top box platorms, and
>>> supports I2C Standard and Fast modes.
>>>
>>> Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
>>> ---
>>> Documentation/devicetree/bindings/i2c/i2c-st.txt | 38 +
>>> drivers/i2c/busses/Kconfig | 10 +
>>> drivers/i2c/busses/Makefile | 1 +
>>> drivers/i2c/busses/i2c-st.c | 867 ++++++++++++++++++++++
>>> 4 files changed, 916 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/i2c/i2c-st.txt
>>> create mode 100644 drivers/i2c/busses/i2c-st.c
>>>
>>> diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
>>> new file mode 100644
>>> index 0000000..8b2fd0b
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt
>>> @@ -0,0 +1,38 @@
>>> +ST SSC binding, for I2C mode operation
>>> +
>>> +Required properties :
>>> +- compatible : Must be "st,comms-i2c"
>>> +- reg : Offset and length of the register set for the device
>>> +- interrupts : the interrupt specifier
>>> +- clock-names: Must contain "ssc".
>>> +- clocks: Must contain an entry for each name in clock-names. See the common
>>> + clock bindings.
>>> +- A pinctrl state named "default" must be defined, using the bindings in
>>> + ../pinctrl/pinctrl-binding.txt
>>> +
>>> +Optional properties :
>>> +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
>>> + the default 100 kHz frequency will be used. As only Normal and Fast modes
>>> + are supported, possible values are 100000 and 400000.
>>> +- i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
>>> + allowed through the deglitch circuit. In units of us.
>>> +- i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
>>> + allowed through the deglitch circuit. In units of us.
>> i2c-min... should be vendor prefixed, st,i2c-min...
> This was already discussed in earlier revisions of the patches.
> Initially this was prefixed with "st,", but Wolfram asked to put these properties as generic.
> As explained in the cover letter, there are no I2C DT binding documentation for now, but it is in Wolfram's ToDo list.
> As soon as Wolfram has created the documentation, I will create a patch to document
>
> i2c-min-scl-pulse-width-us and i2c-min-sda-pulse-width-us there.

Missed that, would be good to maybe comment about that in the commit message.. Or is there some reason to not just put them into a i2c/i2c-bus.txt right now?

>>>
>>> +- A pinctrl state named "sleep" could be defined, using the bindings in
>>> + ../pinctrl/pinctrl-binding.txt
>> I don't see any reference to "sleep" in pinctrl-binding.txt
> Right, I will correct that.
>
> Thanks for the review,
> Maxime

- k

--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation



\
 
 \ /
  Last update: 2013-10-29 17:01    [W:0.074 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site