lkml.org 
[lkml]   [2013]   [Oct]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] ata: ahci_platform: Manage SATA PHY
Date
From: Balaji T K <balajitk@ti.com>

Some platforms have a PHY hooked up to the
SATA controller. The PHY needs to be initialized
and powered up for SATA to work. We do that
using the PHY framework.

[Roger Q] Cleaned up.

CC: Tejun Heo <tj@kernel.org>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
.../devicetree/bindings/ata/ahci-platform.txt | 3 +-
drivers/ata/ahci.h | 2 ++
drivers/ata/ahci_platform.c | 29 +++++++++++++++++++-
3 files changed, 32 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index 89de156..c8a6cea 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -4,7 +4,8 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA controller should have its own node.

Required properties:
-- compatible : compatible list, contains "snps,spear-ahci"
+- compatible : compatible list, contains "snps,spear-ahci",
+ snps,exynos5440-ahci or "snps,dwc-ahci"
- interrupts : <interrupt mapping for SATA IRQ>
- reg : <registers mapping>

diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h
index 1145637..94484cb 100644
--- a/drivers/ata/ahci.h
+++ b/drivers/ata/ahci.h
@@ -37,6 +37,7 @@

#include <linux/clk.h>
#include <linux/libata.h>
+#include <linux/phy/phy.h>

/* Enclosure Management Control */
#define EM_CTRL_MSG_TYPE 0x000f0000
@@ -322,6 +323,7 @@ struct ahci_host_priv {
u32 em_buf_sz; /* EM buffer size in byte */
u32 em_msg_type; /* EM message type */
struct clk *clk; /* Only for platforms supporting clk */
+ struct phy *phy; /* If platforms use phy */
void *plat_data; /* Other platform data */
};

diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 2daaee0..5a0f1418 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -141,6 +141,21 @@ static int ahci_probe(struct platform_device *pdev)
}
}

+ hpriv->phy = devm_phy_get(dev, "sata-phy");
+ if (IS_ERR(hpriv->phy)) {
+ dev_dbg(dev, "can't get sata-phy\n");
+ /* return only if -EPROBE_DEFER */
+ if (PTR_ERR(hpriv->phy) == -EPROBE_DEFER) {
+ rc = -EPROBE_DEFER;
+ goto disable_unprepare_clk;
+ }
+ }
+
+ if (!IS_ERR(hpriv->phy)) {
+ phy_init(hpriv->phy);
+ phy_power_on(hpriv->phy);
+ }
+
/*
* Some platforms might need to prepare for mmio region access,
* which could be done in the following init call. So, the mmio
@@ -150,7 +165,7 @@ static int ahci_probe(struct platform_device *pdev)
if (pdata && pdata->init) {
rc = pdata->init(dev, hpriv->mmio);
if (rc)
- goto disable_unprepare_clk;
+ goto disable_phy;
}

ahci_save_initial_config(dev, hpriv,
@@ -220,6 +235,12 @@ static int ahci_probe(struct platform_device *pdev)
pdata_exit:
if (pdata && pdata->exit)
pdata->exit(dev);
+disable_phy:
+ if (!IS_ERR(hpriv->phy)) {
+ phy_power_off(hpriv->phy);
+ phy_exit(hpriv->phy);
+ }
+
disable_unprepare_clk:
if (!IS_ERR(hpriv->clk))
clk_disable_unprepare(hpriv->clk);
@@ -238,6 +259,11 @@ static void ahci_host_stop(struct ata_host *host)
if (pdata && pdata->exit)
pdata->exit(dev);

+ if (!IS_ERR(hpriv->phy)) {
+ phy_power_off(hpriv->phy);
+ phy_exit(hpriv->phy);
+ }
+
if (!IS_ERR(hpriv->clk)) {
clk_disable_unprepare(hpriv->clk);
clk_put(hpriv->clk);
@@ -328,6 +354,7 @@ static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_suspend, ahci_resume);
static const struct of_device_id ahci_of_match[] = {
{ .compatible = "snps,spear-ahci", },
{ .compatible = "snps,exynos5440-ahci", },
+ { .compatible = "snps,dwc-ahci", },
{},
};
MODULE_DEVICE_TABLE(of, ahci_of_match);
--
1.7.9.5


\
 
 \ /
  Last update: 2013-10-16 14:01    [W:0.055 / U:0.628 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site