lkml.org 
[lkml]   [2013]   [Oct]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/7] usb: dwc3: adapt dwc3 core to use Generic PHY Framework
Hi,

On Mon, Oct 14, 2013 at 01:21:29PM +0300, Roger Quadros wrote:
> +Vivek
>
> On 10/14/2013 12:26 PM, Kishon Vijay Abraham I wrote:
> > Hi Roger,
> >
> > On Friday 11 October 2013 08:39 PM, Roger Quadros wrote:
> >> Hi,
> >>
> >> On 09/02/2013 06:43 PM, Kishon Vijay Abraham I wrote:
> >>> Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
> >>> power_on and power_off the following APIs are used phy_init(), phy_exit(),
> >>> phy_power_on() and phy_power_off().
> >>>
> >>> However using the old USB phy library wont be removed till the PHYs of all
> >>> other SoC's using dwc3 core is adapted to the Generic PHY Framework.
> >>>
> >>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
> >>> ---
> >>> Documentation/devicetree/bindings/usb/dwc3.txt | 6 ++-
> >>> drivers/usb/dwc3/Kconfig | 1 +
> >>> drivers/usb/dwc3/core.c | 49 ++++++++++++++++++++++++
> >>> drivers/usb/dwc3/core.h | 7 ++++
> >>> 4 files changed, 61 insertions(+), 2 deletions(-)
> >>>
> >>> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> >>> index e807635..471366d 100644
> >>> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> >>> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
> >>> @@ -6,11 +6,13 @@ Required properties:
> >>> - compatible: must be "snps,dwc3"
> >>> - reg : Address and length of the register set for the device
> >>> - interrupts: Interrupts used by the dwc3 controller.
> >>> +
> >>> +Optional properties:
> >>> - usb-phy : array of phandle for the PHY device. The first element
> >>> in the array is expected to be a handle to the USB2/HS PHY and
> >>> the second element is expected to be a handle to the USB3/SS PHY
> >>> -
> >>> -Optional properties:
> >>> + - phys: from the *Generic PHY* bindings
> >>> + - phy-names: from the *Generic PHY* bindings
> >>> - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
> >>>
> >>> This is usually a subnode to DWC3 glue to which it is connected.
> >>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> >>> index cfc16dd..ad7ce83 100644
> >>> --- a/drivers/usb/dwc3/Kconfig
> >>> +++ b/drivers/usb/dwc3/Kconfig
> >>> @@ -3,6 +3,7 @@ config USB_DWC3
> >>> depends on (USB || USB_GADGET) && GENERIC_HARDIRQS && HAS_DMA
> >>> depends on EXTCON
> >>> select USB_PHY
> >>> + select GENERIC_PHY
> >>> select USB_XHCI_PLATFORM if USB_SUPPORT && USB_XHCI_HCD
> >>> help
> >>> Say Y or M here if your system has a Dual Role SuperSpeed
> >>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> >>> index 428c29e..485d365 100644
> >>> --- a/drivers/usb/dwc3/core.c
> >>> +++ b/drivers/usb/dwc3/core.c
> >>> @@ -82,6 +82,12 @@ static void dwc3_core_soft_reset(struct dwc3 *dwc)
> >>>
> >>> usb_phy_init(dwc->usb2_phy);
> >>> usb_phy_init(dwc->usb3_phy);
> >>
> >> How about adding
> >> + if (dwc->usb2_phy)
> >> + usb_phy_init(dwc->usb2_phy);
> >> + if (dwc->usb3_phy)
> >> + usb_phy_init(dwc->usb3_phy);
> >
> > Thankfully that usb_phy_init will check if phy is NULL.
> >>
> >> both usb phy and generic phy shouldn't be present together.
> >
> > ok.
> >>
> >>> +
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_init(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_init(dwc->usb3_generic_phy);
> >>> +
> >>> mdelay(100);
> >>>
> >>> /* Clear USB3 PHY reset */
> >>> @@ -343,6 +349,11 @@ static void dwc3_core_exit(struct dwc3 *dwc)
> >>> {
> >>> usb_phy_shutdown(dwc->usb2_phy);
> >>> usb_phy_shutdown(dwc->usb3_phy);
> >>
> >> here as well
> >>
> >>> +
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_power_off(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_power_off(dwc->usb3_generic_phy);
> >>> }
> >>>
> >>> #define DWC3_ALIGN_MASK (16 - 1)
> >>> @@ -427,6 +438,23 @@ static int dwc3_probe(struct platform_device *pdev)
> >>> dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
> >>> }
> >>>
> >>> + if (of_property_read_bool(node, "phys") || pdata->has_phy) {
> >>> + dwc->usb2_generic_phy = devm_phy_get(dev, "usb2-phy");
> >>> + if (IS_ERR(dwc->usb2_generic_phy)) {
> >>> + dev_err(dev, "no usb2 phy configured yet");
> >>> + return PTR_ERR(dwc->usb2_generic_phy);
> >>> + }
> >>> +
> >>> + dwc->usb3_generic_phy = devm_phy_get(dev, "usb3-phy");
> >>> + if (IS_ERR(dwc->usb3_generic_phy)) {
> >>> + dev_err(dev, "no usb3 phy configured yet");
> >>> + return PTR_ERR(dwc->usb3_generic_phy);
> >>> + }
> >>
> >> better to add
> >> + /* Don't use USB PHY if generic PHY was found */
> >> + dwc->usb2_phy = dwc->usb3_phy = NULL;
> >
> > ok.
> >>
> >>> + } else {
> >>
> >> not required as we've used kzalloc for dwc.
> >>
> >>> + dwc->usb2_generic_phy = NULL;
> >>> + dwc->usb3_generic_phy = NULL;
> >>> + }
> >>> +
> >>> /* default to superspeed if no maximum_speed passed */
> >>> if (dwc->maximum_speed == USB_SPEED_UNKNOWN)
> >>> dwc->maximum_speed = USB_SPEED_SUPER;
> >>> @@ -450,6 +478,11 @@ static int dwc3_probe(struct platform_device *pdev)
> >>
> >> if (dwc->usb2_phy)
> >>
> >>> usb_phy_set_suspend(dwc->usb2_phy, 0);
> >>
> >> if (dwc->usb3_phy)
> >>
> >>> usb_phy_set_suspend(dwc->usb3_phy, 0);
> >>>
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_power_on(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_power_on(dwc->usb3_generic_phy);
> >>> +
> >>> spin_lock_init(&dwc->lock);
> >>> platform_set_drvdata(pdev, dwc);
> >>>
> >>> @@ -576,6 +609,11 @@ static int dwc3_remove(struct platform_device *pdev)
> >>
> >> if (dwc->usb2_phy)
> >>> usb_phy_set_suspend(dwc->usb2_phy, 1);
> >>
> >> if (dwc->usb3_phy)
> >>> usb_phy_set_suspend(dwc->usb3_phy, 1);
> >>>
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_power_off(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_power_off(dwc->usb3_generic_phy);
> >>> +
> >>> pm_runtime_put(&pdev->dev);
> >>> pm_runtime_disable(&pdev->dev);
> >>>
> >>> @@ -673,6 +711,11 @@ static int dwc3_suspend(struct device *dev)
> >>
> >> if (dwc->usb3_phy)
> >>> usb_phy_shutdown(dwc->usb3_phy);
> >>
> >> if (dwc->usb2_phy)
> >>> usb_phy_shutdown(dwc->usb2_phy);
> >>>
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_exit(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_exit(dwc->usb3_generic_phy);
> >>> +
> >>> return 0;
> >>> }
> >>>
> >>> @@ -683,6 +726,12 @@ static int dwc3_resume(struct device *dev)
> >>>
> >>
> >> if (dwc->usb3_phy)
> >>> usb_phy_init(dwc->usb3_phy);
> >>
> >> if (dwc->usb2_phy)
> >>> usb_phy_init(dwc->usb2_phy);
> >>> +
> >>> + if (dwc->usb2_generic_phy)
> >>> + phy_init(dwc->usb2_generic_phy);
> >>> + if (dwc->usb3_generic_phy)
> >>> + phy_init(dwc->usb3_generic_phy);
> >>> +
> >>> msleep(100);
> >>>
> >>> spin_lock_irqsave(&dwc->lock, flags);
> >>> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> >>> index f8af8d4..01ec7d7 100644
> >>> --- a/drivers/usb/dwc3/core.h
> >>> +++ b/drivers/usb/dwc3/core.h
> >>> @@ -31,6 +31,8 @@
> >>> #include <linux/usb/gadget.h>
> >>> #include <linux/usb/otg.h>
> >>>
> >>> +#include <linux/phy/phy.h>
> >>> +
> >>> /* Global constants */
> >>> #define DWC3_EP0_BOUNCE_SIZE 512
> >>> #define DWC3_ENDPOINTS_NUM 32
> >>> @@ -613,6 +615,8 @@ struct dwc3_scratchpad_array {
> >>> * @dr_mode: requested mode of operation
> >>> * @usb2_phy: pointer to USB2 PHY
> >>> * @usb3_phy: pointer to USB3 PHY
> >>> + * @usb2_generic_phy: pointer to USB2 PHY
> >>> + * @usb3_generic_phy: pointer to USB3 PHY
> >>> * @dcfg: saved contents of DCFG register
> >>> * @gctl: saved contents of GCTL register
> >>> * @is_selfpowered: true when we are selfpowered
> >>> @@ -665,6 +669,9 @@ struct dwc3 {
> >>> struct usb_phy *usb2_phy;
> >>> struct usb_phy *usb3_phy;
> >>>
> >>> + struct phy *usb2_generic_phy;
> >>> + struct phy *usb3_generic_phy;
> >>> +
> >>> void __iomem *regs;
> >>> size_t regs_size;
> >>>
> >>>
> >
> > Do you have any suggestions on how to get only individual PHYs? like only
> > usb2phy or usb3phy?
>
> My earlier understanding was that both PHYs are needed only if .speed is "super-speed"
> and only usb2phy is needed for "high-speed". But as per Vivek's email it seems
> Samsung's exynos5 SoC doesn't need usb2phy for "super-speed".
>
> So to keeps things flexible, I can propose the following approach
> - if speed == 'high-speed' usb2phy must be present. usb3phy will be ignored if supplied.
> - if speed == 'super-speed' usb3phy must be present and usb2phy is optional but must be
> initialized if supplied.
> - if speed is not specified, we default to 'super-speed'.
>
> Felipe, does this address the issue you were facing with OMAP5?

on OMAP5 we cannot skip USB3 PHY initialization. But then it becomes a
question of supporting a test feature (in OMAP5 case it would be cool to
force controller to lower speeds for testing) or coping with a broken
DTS.

--
balbi
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-10-15 14:21    [W:0.142 / U:1.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site