lkml.org 
[lkml]   [2013]   [Oct]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/5] thermal: exynos: Provide initial setting for TMU's test MUX address at Exynos4412
On 14-10-2013 11:00, Lukasz Majewski wrote:
> Hi Eduardo,
>
>> On 09-10-2013 02:29, Lukasz Majewski wrote:
>>> The commit d0a0ce3e77c795258d47f9163e92d5031d0c5221 ("thermal:
>>> exynos: Add missing definations and code cleanup") has removed
>>> setting of test MUX address value at TMU configuration setting.
>>>
>>> This field is not present on Exynos4210 and Exynos5 SoCs. However
>>> on Exynos4412 SoC it is required to set this field after reset
>>> because without it TMU shows maximal available temperature, which
>>> causes immediate platform shutdown.
>>>
>>> Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
>>> Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
>>> Reviewed-by: Tomasz Figa <t.figa@samsung.com>
>>>
>>> ---
>>> Changes for v2:
>>> - Define test_mux and test_mux_addr_shift to not use direct
>>> register access
>>> - Remove pdata->type == SOC_ARCH_EXYNOS4412 check at
>>> exynos_tmu_control() and use only generic code
>>>
>>> drivers/thermal/samsung/exynos_tmu.c | 3 +++
>>> drivers/thermal/samsung/exynos_tmu.h | 4 ++++
>>> drivers/thermal/samsung/exynos_tmu_data.c | 2 ++
>>> drivers/thermal/samsung/exynos_tmu_data.h | 4 ++++
>>> 4 files changed, 13 insertions(+)
>>>
>>> diff --git a/drivers/thermal/samsung/exynos_tmu.c
>>> b/drivers/thermal/samsung/exynos_tmu.c index 1312b34..32f38b9 100644
>>> --- a/drivers/thermal/samsung/exynos_tmu.c
>>> +++ b/drivers/thermal/samsung/exynos_tmu.c
>>> @@ -317,6 +317,9 @@ static void exynos_tmu_control(struct
>>> platform_device *pdev, bool on)
>>> con = readl(data->base + reg->tmu_ctrl);
>>>
>>> + if (pdata->test_mux)
>>
>>
>> test_mux field is in fact an address, correct? Can 0 be a valid
>> address?
>
> No it isn't an address. It is the value which shall be written to
> test_mux field of TMU_CONTROL register.
>
>>
>> Why not using the feature flags to test for capabilities,
>
> It is easier to assign value to test_mux tmu_data struct, than write
> separate set of features for Exynos4412 and Exynos5250, which share the
> code.
>

It is harder to write, yes, but things that are easy to write are
usually harder to read. Besides, my concern is if 0x0 is a valid value
to be written. And if yes, then makes the patch you sent might be
incomplete.

> Also .features seems to define SoC independent features of TMU IP (like
> TMU_SUPPORT_EMULATION).
>
> The TEST_MUX setting is platform dependent (only Exynos4412 uses it),
> so this is the rationale to define it at tmu platform data.
>

Is test mux something pinctrl should be handling?

>> features and
>> required configurations instead of assuming obscure domain and address
>> ranges?
>
> TMU_MUX only uses
>
> (test_mux << test_mux_addr_shift) at tmu_ctrl register.
>
>
>>
>>
>>> + con |= (pdata->test_mux <<
>>> reg->test_mux_addr_shift); +
>>> if (pdata->reference_voltage) {
>>> con &= ~(reg->buf_vref_sel_mask <<
>>> reg->buf_vref_sel_shift); con |= pdata->reference_voltage <<
>>> reg->buf_vref_sel_shift; diff --git
>>> a/drivers/thermal/samsung/exynos_tmu.h
>>> b/drivers/thermal/samsung/exynos_tmu.h index b42ece4..3fb6554
>>> 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++
>>> b/drivers/thermal/samsung/exynos_tmu.h @@ -85,6 +85,7 @@ enum
>>> soc_type {
>>> * @triminfo_reload_shift: shift of triminfo reload enable bit in
>>> triminfo_ctrl reg.
>>> * @tmu_ctrl: TMU main controller register.
>>> + * @test_mux_addr_shift: shift bits of test mux address.
>>> * @buf_vref_sel_shift: shift bits of reference voltage in
>>> tmu_ctrl register.
>>> * @buf_vref_sel_mask: mask bits of reference voltage in tmu_ctrl
>>> register.
>>> * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl
>>> register. @@ -151,6 +152,7 @@ struct exynos_tmu_registers {
>>> u32 triminfo_reload_shift;
>>>
>>> u32 tmu_ctrl;
>>> + u32 test_mux_addr_shift;
>>> u32 buf_vref_sel_shift;
>>> u32 buf_vref_sel_mask;
>>> u32 therm_trip_mode_shift;
>>> @@ -258,6 +260,7 @@ struct exynos_tmu_registers {
>>> * @first_point_trim: temp value of the first point trimming
>>> * @second_point_trim: temp value of the second point trimming
>>> * @default_temp_offset: default temperature offset in case of no
>>> trimming
>>> + * @test_mux; information if SoC supports test MUX
>>> * @cal_type: calibration type for temperature
>>> * @cal_mode: calibration mode for temperature
>>> * @freq_clip_table: Table representing frequency reduction
>>> percentage. @@ -287,6 +290,7 @@ struct exynos_tmu_platform_data {
>>> u8 first_point_trim;
>>> u8 second_point_trim;
>>> u8 default_temp_offset;
>>> + u8 test_mux;
>>>
>>> enum calibration_type cal_type;
>>> enum calibration_mode cal_mode;
>>> diff --git a/drivers/thermal/samsung/exynos_tmu_data.c
>>> b/drivers/thermal/samsung/exynos_tmu_data.c index d8de5c1..073c292
>>> 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c
>>> +++ b/drivers/thermal/samsung/exynos_tmu_data.c
>>> @@ -98,6 +98,7 @@ static const struct exynos_tmu_registers
>>> exynos4412_tmu_registers = { .triminfo_ctrl =
>>> EXYNOS_TMU_TRIMINFO_CON, .triminfo_reload_shift =
>>> EXYNOS_TRIMINFO_RELOAD_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
>>> + .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
>>> .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
>>> .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
>>> .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
>>> @@ -174,6 +175,7 @@ struct exynos_tmu_init_data const
>>> exynos4412_default_tmu_data = { {
>>> EXYNOS4412_TMU_DATA,
>>> .type = SOC_ARCH_EXYNOS4412,
>>> + .test_mux = EXYNOS4412_MUX_ADDR_VALUE,
>>> },
>>> },
>>> .tmu_count = 1,
>>> diff --git a/drivers/thermal/samsung/exynos_tmu_data.h
>>> b/drivers/thermal/samsung/exynos_tmu_data.h index b130b1e..a1ea19d
>>> 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h
>>> +++ b/drivers/thermal/samsung/exynos_tmu_data.h
>>> @@ -95,6 +95,10 @@
>>>
>>> #define EXYNOS_MAX_TRIGGER_PER_REG 4
>>>
>>> +/* Exynos4412 specific */
>>> +#define EXYNOS4412_MUX_ADDR_VALUE 6
>>
>>> +#define EXYNOS4412_MUX_ADDR_SHIFT 20
>>> +
>>> /*exynos5440 specific registers*/
>>> #define EXYNOS5440_TMU_S0_7_TRIM 0x000
>>> #define EXYNOS5440_TMU_S0_7_CTRL 0x020
>>>
>>
>>
>
>
>


--
You have got to be excited about what you are doing. (L. Lamport)

Eduardo Valentin

[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2013-10-14 21:41    [W:0.120 / U:1.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site