lkml.org 
[lkml]   [2013]   [Jan]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC] OMAP: 4430sdp: add shared trasport devices to the board file
Date
Add the btwilink, nfcwilink and shared transport devices to the board
file, including functions to power things on and off.

Additionally, add the UART2 muxing data, so it's properly configured.

Signed-off-by: Luciano Coelho <coelho@ti.com>
---

This is pretty much the same as the patch I just sent for panda, but
there were a few more things missing in the 4430sdp board file and I
also included NFC support.

I'm sending this as RFC because I'm not sure this is the right thing
to do for 4430sdp. This configuration works when the WiLink COM8
module is installed. The WLAN support is already hardcoded in this
file, so adding shared transport (BT/NFC/FM/GPS) support at least
won't make things much worse.

Additionally, only WiLink8 has optional support for NFC and I'm not
sure there is a way to figure that out at runtime.

arch/arm/mach-omap2/board-4430sdp.c | 76 +++++++++++++++++++++++++++++++++++
1 file changed, 76 insertions(+)

diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 1cc6696..7cf273e 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -29,6 +29,8 @@
#include <linux/platform_data/omap4-keypad.h>
#include <linux/usb/musb.h>

+#include <linux/ti_wilink_st.h>
+
#include <asm/hardware/gic.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -53,6 +55,7 @@
#define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO 184
#define OMAP4_SFH7741_ENABLE_GPIO 188

+#define GPIO_BT_EN 55
#define GPIO_WIFI_PMENA 54
#define GPIO_WIFI_IRQ 53

@@ -408,6 +411,66 @@ static struct platform_device sdp4430_abe_audio = {
},
};

+/* TI shared transport for Bluetooth and NFC */
+static int plat_kim_chip_enable(struct kim_data_s *kim_data)
+{
+ gpio_set_value(GPIO_BT_EN, GPIO_LOW);
+ mdelay(5);
+ gpio_set_value(GPIO_BT_EN, GPIO_HIGH);
+ mdelay(100);
+
+ return 0;
+}
+
+static int plat_kim_chip_disable(struct kim_data_s *kim_data)
+{
+ gpio_set_value(GPIO_BT_EN, GPIO_LOW);
+ mdelay(1);
+ gpio_set_value(GPIO_BT_EN, GPIO_HIGH);
+ mdelay(1);
+ gpio_set_value(GPIO_BT_EN, GPIO_LOW);
+
+ return 0;
+}
+
+static struct ti_st_plat_data wilink_pdata = {
+ .dev_name = "/dev/ttyO1",
+ .flow_cntrl = 1,
+ .baud_rate = 3000000,
+ .chip_enable = plat_kim_chip_enable,
+ .chip_disable = plat_kim_chip_disable,
+};
+
+static int wilink_st_init(void)
+{
+ int status;
+
+ status = gpio_request_one(GPIO_BT_EN, GPIOF_OUT_INIT_LOW, "kim");
+ if (status)
+ pr_err("%s: failed to request gpio %d\n", __func__,
+ GPIO_BT_EN);
+
+ return status;
+}
+
+static struct platform_device wl12xx_device = {
+ .name = "kim",
+ .id = -1,
+ .dev = {
+ .platform_data = &wilink_pdata,
+ },
+};
+
+static struct platform_device btwilink_device = {
+ .name = "btwilink",
+ .id = -1,
+};
+
+static struct platform_device nfcwilink_device = {
+ .name = "nfcwilink",
+ .id = -1,
+};
+
static struct platform_device *sdp4430_devices[] __initdata = {
&sdp4430_gpio_keys_device,
&sdp4430_leds_gpio,
@@ -416,6 +479,9 @@ static struct platform_device *sdp4430_devices[] __initdata = {
&sdp4430_dmic_codec,
&sdp4430_abe_audio,
&sdp4430_hdmi_audio_codec,
+ &wl12xx_device,
+ &btwilink_device,
+ &nfcwilink_device,
};

static struct omap_musb_board_data musb_board_data = {
@@ -632,6 +698,12 @@ static struct omap_board_mux board_mux[] __initdata = {
OMAP_PULL_ENA),
OMAP4_MUX(ABE_MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),

+ /* UART2 - BT/FM/GPS shared transport */
+ OMAP4_MUX(UART2_CTS, OMAP_PIN_INPUT | OMAP_MUX_MODE0),
+ OMAP4_MUX(UART2_RTS, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+ OMAP4_MUX(UART2_RX, OMAP_PIN_INPUT | OMAP_MUX_MODE0),
+ OMAP4_MUX(UART2_TX, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0),
+
{ .reg_offset = OMAP_MUX_TERMINATOR },
};

@@ -711,6 +783,10 @@ static void __init omap_4430sdp_init(void)
if (status)
pr_err("Keypad initialization failed: %d\n", status);

+ status = wilink_st_init();
+ if (status)
+ pr_err("WiLink shared transport init failed: %d\n", status);
+
omap_4430sdp_display_init();
}

--
1.7.10.4


\
 
 \ /
  Last update: 2013-01-16 23:41    [W:0.025 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site