lkml.org 
[lkml]   [2012]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: rtl8192se hanging completely
From
Hi all,

(please cc)

I have now changed my home router and with the new one it
is working without problems at home, and with a few
hickups at work, too.

But still, at work after some time the connection breaks.
I found the following interesting messages in the log:
dmar: DRHD: handling fault status reg 3
dmar: DMAR:[DMA Read] Request device [03:00.0] fault addr fff73000
DMAR:[fault reason 06] PTE Read access is not set
around the time the connection hangs and never comes back.

The mentioned device 03:00.0 is the wlan adapter:
$ lspci -v -s 03:00.0
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Flags: bus master, fast devsel, latency 0, IRQ 17
I/O ports at 2000 [size=256]
Memory at f0500000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Legacy Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 88-55-22-fe-ff-4c-e0-00
Kernel driver in use: rtl8192se
$

That is with latest git kernel from yesterday.

Any suggestions would be appreciated.

On Wed, 22 Aug 2012, Norbert Preining wrote:
> Dear all,
>
> (please cc)
>
> I am having serious troubles with my rtl8192se card:
>
> kernel: 3.6.0-rc2+, compiled from git today, same with rc1
> rtl8192se in kernel driver, loaded with debug=3
> Debian sid
> Lenovo Thinkpad Edge
>
> When starting from cold boot, the driver associates, but no packet
> whatsoever leaves the computer it seems, pinging the gateway
> does not return anything, and ns lookups are not working.
>
> In the logs I see many instances of:
> rtlwifi:rtl_tx_agg_start():<0-0> on ra = 00:0a:79:eb:56:10 tid = 6 seq:39
> rtlwifi:rtl_action_proc():<200-1> Tx ACT_ADDBAREQ From :88:9f:fa:f9:07:28
> rtlwifi:rtl_tx_agg_stop():<0-0> on ra = 00:0a:79:eb:56:10 tid = 6
> rtlwifi:rtl_action_proc():<400-1> ACT_ADDBADEL From :88:9f:fa:f9:07:28
> rtlwifi:rtl_action_proc():<10000-1> Rx ACT_ADDBARSP From :00:0a:79:eb:56:10
> in various orders.
>
>
> trying to remove the module gave me:
> [ 649.459652] wlan0: deauthenticating from 00:0a:79:eb:56:10 by local choice (reason=3)
> [ 649.459701] rtlwifi:rtl_tx_agg_stop():<0-0> on ra = 00:0a:79:eb:56:10 tid = 0
> [ 659.094654] rtlwifi:rtl_op_set_key():<0-0> Disabling hardware based encryption for keyidx: 0, mac: 00:0a:79:eb:56:10
> [ 659.094659] rtlwifi:rtl_op_set_key():<0-0> alg:CCMP
> [ 659.094663] rtlwifi:rtl_op_set_key():<0-0> set enable_hw_sec, key_type:4(OPEN:0 WEP40:1 TKIP:2 AES:4 WEP104:5)
> [ 659.094667] rtlwifi:rtl_op_set_key():<0-0> disable key delete one entry
> [ 659.094670] rtlwifi:rtl_cam_delete_one_entry():<0-0> key_idx:0
> [ 659.094673] rtlwifi:rtl_cam_delete_one_entry():<0-0> rtl_cam_delete_one_entry(): WRITE A4: 0
> [ 659.094676] rtlwifi:rtl_cam_delete_one_entry():<0-0> rtl_cam_delete_one_entry(): WRITE A0: 80010000
> [ 659.094719] rtlwifi:rtl_op_sta_remove():<0-0> Remove sta addr is 00:0a:79:eb:56:10
> [ 659.142712] rtlwifi:rtl_op_bss_info_changed():<0-0> BSS_CHANGED_UN_ASSOC
> [ 659.142725] rtlwifi:rtl_op_bss_info_changed():<0-0> 00:00:00:00:00:00
> [ 659.190740] rtlwifi:rtl_op_set_key():<0-0> Disabling hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
> [ 659.190744] rtlwifi:rtl_op_set_key():<0-0> alg:TKIP
> [ 659.190747] rtlwifi:rtl_op_set_key():<0-0> set enable_hw_sec, key_type:2(OPEN:0 WEP40:1 TKIP:2 AES:4 WEP104:5)
> [ 659.190750] rtlwifi:rtl_op_set_key():<0-0> disable key delete one entry
> [ 659.190753] rtlwifi:rtl_cam_delete_one_entry():<0-0> key_idx:1
> [ 659.190756] rtlwifi:rtl_cam_delete_one_entry():<0-0> rtl_cam_delete_one_entry(): WRITE A4: 0
> [ 659.190759] rtlwifi:rtl_cam_delete_one_entry():<0-0> rtl_cam_delete_one_entry(): WRITE A0: 80010008
>
>
> After that I reloaded the module and then it is getting worse:
> rtl8192se 0000:03:00.0: Refused to change power state, currently in D3
> rtl8192se:_rtl92se_read_adapter_info():<0-0> RTL819X Not boot from eeprom, check it !!
> tl8192se: FW Power Save off (module option)
> rtl8192se: Driver for Realtek RTL8192SE/RTL8191SE
> Loading firmware rtlwifi/rtl8192sefw.bin
> ...
> rtl8192se:_rtl92se_macconfig_after_fwdownload():<0-0> OK
> rtl8192se:rtl92s_phy_bb_config():<0-0> RF_Type(0) does not match RF_Num(4)!!
> rtl8192se:rtl92s_phy_bb_config():<0-0> path1 0xf, path2 0xf, pathmap 0xf
> rtlwifi:rtl_pci_start():<0-0> OK
> rtl8192se:rtl92s_phy_chk_fwcmd_iodone():<0-0> Set FW Cmd fail!!
> rtl8192se:rtl92s_phy_chk_fwcmd_iodone():<0-0> Set FW Cmd fail!!
> rtl8192se:rtl92s_phy_set_rf_power_state():<0-0> IPS Set eRf nic disable
>
> rtl8192se:rtl92s_phy_set_rf_power_state():<0-1> IPS Set eRf nic enable
> rtl8192se:_rtl92se_macconfig_after_fwdownload():<0-1> OK
>
> ...
> rtl8192se:rtl92s_phy_chk_fwcmd_iodone():<0-0> Set FW Cmd fail!!
> rtlwifi:rtl_pci_tx():<200-1> No more TX desc@6, ring->idx = 0, idx = 0, skb_queue_len = 0x0
>
> etc etc.
>
> That is the end, no connection at all, and no way (AFAIS) to get
> it back.
>
> Are there any suggestions, patches, ideas to fix and track that down?


Best wishes

Norbert

----------------------------------------------------------------------------
Norbert Preining preining@{jaist.ac.jp, logic.at, debian.org}
JAIST, Japan TeX Live and Debian Developer
gpg DSA: 0x09C5B094 fp: 14DF 2E6C 0307 BE6D AD76 A9C0 D2BF 4AA3 09C5 B094
----------------------------------------------------------------------------
FULKING (participial vb.)
Pretending not to be in when the carol-singers come round.
--- Douglas Adams, The Meaning of Liff


\
 
 \ /
  Last update: 2012-09-07 03:01    [W:0.322 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site