lkml.org 
[lkml]   [2012]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RESEND] PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled
On Thu, 20 Sep 2012, Rafael J. Wysocki wrote:

> On Thursday, September 20, 2012, Kevin Hilman wrote:
> > From: Kevin Hilman <khilman@ti.com>
> >
> > When runtime PM is disabled, what we want is for callbacks not to be
> > called from then on. However, currently, when runtime PM is disabled,
> > operations such as 'get' will also fail even if the device is
> > currently active.
> >
> > Since calling 'get' on a device that is already RPM_ACTIVE does not
> > involve calling the callbacks, it should be allowed to succeed, even
> > if runtime PM is disabled.
> >
> > This is particularily useful in runtime PM enabled drivers that are
> > used during system suspend. Because runtime PM is disabled during
> > system suspend, currently any driver's use of pm_runtime_get* will
> > fail with -EACCES. This is expected if the device was already runtime
> > suspended, but if the device is actually active (due to recent usage,
> > autosuspend timeout not expired, or pm_runtime_resume() called in
> > ->suspend() method), the pm_runtime_get*() call should actually
> > succeed.
>
> I'd say the problem is when the drive in question uses the return value of
> pm_runtime_get_sync(), for example, to decide whether or not it is safe
> to access the hardware. In that case it may decide that accessing the
> hardware is unsafe during system suspend, although that's not really the
> case. So the change you're proposing allows drivers of this kind (and there
> may be a substantial number of them) to be simplified slightly.

Kevin makes a good case that pm_runtime_resume() and related functions
should succeed even when runtime PM is disabled, if the device is
already in the desired state.

The same may be true for pm_runtime_suspend(). What do you think?

> > To permit the usage described above, add a check to rpm_resume() so
> > that success is returned in the case where a driver is suspended (it's
> > ->suspend callback has been called) but is still RPM_ACTIVE.
> >
> > This patch was developed in close collaboration with Rafael J. Wysocki
> > <rjw@sisk.pl>
> >
> > Tested on AM3730/Beagle-xM where wakeup IRQ firing during the late
> > suspend phase triggers runtime PM activity in the I2C driver since the
> > wakeup IRQ is on an I2C-connected PMIC.
> >
> > Cc: Rafael J. Wysocki <rjw@sisk.pl>
> > Signed-off-by: Kevin Hilman <khilman@ti.com>
>
> OK, I wonder if anyone has any objections against this. Alan?

The way the patch is written contradicts the documentation:

* A request to execute ->runtime_resume() will cancel any pending or
scheduled requests to execute the other callbacks for the same device,
except for scheduled autosuspends.

> > @@ -510,7 +510,8 @@ static int rpm_resume(struct device *dev, int rpmflags)
> > if (dev->power.runtime_error)
> > retval = -EINVAL;
> > else if (dev->power.disable_depth > 0)
> > - retval = -EACCES;
> > + retval = dev->power.is_suspended &&
> > + dev->power.runtime_status == RPM_ACTIVE ? 1 : -EACCES;
> > if (retval)
> > goto out;

Also, the is_suspended test seems irrelevant in general -- it makes
sense in terms of the scenario Kevin described but that's not the
stated purpose of the patch.

Both of these problems can be addressed by writing the code as follows:

if (dev->power.runtime_error)
retval = -EINVAL;
else if (dev->power.disable_depth > 0) {

/* Special case: allow this if the device is already active */
if (dev->power.runtime_status != RPM_ACTIVE)
retval = -EACCES;
}
if (retval)
goto out;

Alan Stern



\
 
 \ /
  Last update: 2012-09-21 20:41    [W:0.091 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site