lkml.org 
[lkml]   [2012]   [Jun]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] spi/pl022: add devicetree support
On Mon, Jun 25, 2012 at 06:06:28PM -0300, Alexandre Pereira da Silva wrote:
[...]
> diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c
[...]
> @@ -1733,7 +1744,7 @@ static int calculate_effective_freq(struct pl022 *pl022, int freq, struct
> * A piece of default chip info unless the platform
> * supplies it.
> */
> -static const struct pl022_config_chip pl022_default_chip_info = {
> +static struct pl022_config_chip pl022_default_chip_info = {
> .com_mode = POLLING_TRANSFER,
> .iface = SSP_INTERFACE_MOTOROLA_SPI,
> .hierarchy = SSP_SLAVE,

What's the reason for removing the const? You're only reading data from
the structure.

[...]
> @@ -1998,8 +2039,14 @@ pl022_probe(struct amba_device *adev, const struct amba_id *id)
> goto err_no_pdata;
> }
>
> + num_cs = platform_info->num_chipselect;
> +#ifdef CONFIG_OF
> + of_property_read_u32(np, "pl022,num-chipselects", &num_cs);
> +#endif

This...

[...]
> @@ -2017,13 +2064,40 @@ pl022_probe(struct amba_device *adev, const struct amba_id *id)
> * on this board
> */
> master->bus_num = platform_info->bus_id;
> - master->num_chipselect = platform_info->num_chipselect;
> + master->num_chipselect = num_cs;
> master->cleanup = pl022_cleanup;
> master->setup = pl022_setup;
> master->prepare_transfer_hardware = pl022_prepare_transfer_hardware;
> master->transfer_one_message = pl022_transfer_one_message;
> master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware;
> master->rt = platform_info->rt;
> + master->dev.of_node = dev->of_node;
> +
> +#ifdef CONFIG_OF
> + for (i = 0; i < num_cs; i++) {
> + int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
> +
> + if (cs_gpio == -EPROBE_DEFER) {
> + status = -EPROBE_DEFER;
> + goto err_no_gpio;
> + }
> +
> + pl022->chipselect[i] = cs_gpio;
> +
> + if (gpio_is_valid(cs_gpio)) {
> + if (gpio_request(cs_gpio, "ssp-pl022"))
> + dev_err(&adev->dev,
> + "could not request %d gpio\n", cs_gpio);
> + else if (gpio_direction_output(cs_gpio, 1))
> + dev_err(&adev->dev,
> + "could set gpio %d as output\n",
> + cs_gpio);
> + }
> + }
> +#else
> + for (i = 0; i < num_cs; i++)
> + pl022->chipselect[i] = -EINVAL;
> +#endif

... and this would be good candidates for IS_ENABLED(CONFIG_OF).

>
> /*
> * Supports mode 0-3, loopback, and active low CS. Transfers are
> @@ -2130,6 +2204,9 @@ pl022_probe(struct amba_device *adev, const struct amba_id *id)
> err_no_ioremap:
> amba_release_regions(adev);
> err_no_ioregion:
> + #ifdef CONFIG_OF
> + err_no_gpio:
> + #endif

If you use the IS_ENABLED() macro, then you no longer need these either.

Thierry
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2012-06-26 08:41    [W:0.044 / U:0.776 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site