lkml.org 
[lkml]   [2012]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 06/23] ARM: LPC32xx: Add dts for EA3250 reference board
Date
There is another reference/development board for the LPC32xx SoC (besides the
Phytec 3250): The Embedded Artists LPC3250 board. This patch adds a default dts
file for it.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>

---
arch/arm/boot/dts/ea3250.dts | 157 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 157 insertions(+)

--- /dev/null
+++ linux-2.6/arch/arm/boot/dts/ea3250.dts
@@ -0,0 +1,157 @@
+/*
+ * Embedded Artists LPC3250 board
+ *
+ * Copyright 2012 Roland Stigge <stigge@antcom.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "lpc32xx.dtsi"
+
+/ {
+ model = "Embedded Artists LPC3250 board based on NXP LPC3250";
+ compatible = "ea,ea3250", "nxp,lpc3250";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x4000000>;
+ };
+
+ ahb {
+ mac: ethernet@31060000 {
+ phy-mode = "rmii";
+ use-iram;
+ };
+
+ /* Here, choose exactly one from: ohci, usbd */
+ ohci@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+
+/*
+ usbd@31020000 {
+ transceiver = <&isp1301>;
+ status = "okay";
+ };
+*/
+
+ /* 128MB Flash via SLC NAND controller */
+ slc: flash@20020000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nxp,wdr-clks = <14>;
+ nxp,wwidth = <260000000>;
+ nxp,whold = <104000000>;
+ nxp,wsetup = <200000000>;
+ nxp,rdr-clks = <14>;
+ nxp,rwidth = <34666666>;
+ nxp,rhold = <104000000>;
+ nxp,rsetup = <200000000>;
+ nand-on-flash-bbt;
+ gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+ mtd0@00000000 {
+ label = "ea3250-boot";
+ reg = <0x00000000 0x00080000>;
+ read-only;
+ };
+
+ mtd1@00080000 {
+ label = "ea3250-uboot";
+ reg = <0x00080000 0x000c0000>;
+ read-only;
+ };
+
+ mtd2@00140000 {
+ label = "ea3250-kernel";
+ reg = <0x00140000 0x00400000>;
+ };
+
+ mtd3@00540000 {
+ label = "ea3250-rootfs";
+ reg = <0x00540000 0x07ac0000>;
+ };
+ };
+
+ apb {
+ uart5: serial@40090000 {
+ status = "okay";
+ };
+
+ uart3: serial@40080000 {
+ status = "okay";
+ };
+
+ uart6: serial@40098000 {
+ status = "okay";
+ };
+
+ i2c1: i2c@400A0000 {
+ clock-frequency = <100000>;
+
+ eeprom@50 {
+ compatible = "at,24c256";
+ reg = <0x50>;
+ };
+
+ eeprom@57 {
+ compatible = "at,24c64";
+ reg = <0x57>;
+ };
+
+ uda1380: uda1380@18 {
+ compatible = "nxp,uda1380";
+ reg = <0x18>;
+ power-gpio = <&gpio 0x59 0>;
+ reset-gpio = <&gpio 0x51 0>;
+ dac-clk = "wspll";
+ };
+
+ pca9532: pca9532@60 {
+ compatible = "nxp,pca9532";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x60>;
+ };
+ };
+
+ i2c2: i2c@400A8000 {
+ clock-frequency = <100000>;
+ };
+
+ i2cusb: i2c@31020300 {
+ clock-frequency = <100000>;
+
+ isp1301: usb-transceiver@2d {
+ compatible = "nxp,isp1301";
+ reg = <0x2d>;
+ };
+ };
+
+ sd@20098000 {
+ wp-gpios = <&pca9532 5 0>;
+ cd-gpios = <&pca9532 4 0>;
+ cd-inverted;
+ bus-width = <4>;
+ status = "okay";
+ };
+ };
+
+ fab {
+ uart1: serial@40014000 {
+ status = "okay";
+ };
+ };
+ };
+};

\
 
 \ /
  Last update: 2012-06-14 19:41    [W:0.167 / U:19.276 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site