lkml.org 
[lkml]   [2012]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2] MMC: core: cap MMC card timeouts at 2 seconds.
On 01/06/12 12:32, Torne (Richard Coles) wrote:
> On 1 June 2012 10:31, Torne (Richard Coles) <torne@google.com> wrote:
>> On 1 June 2012 09:35, Adrian Hunter <adrian.hunter@intel.com> wrote:
>>> On 29/05/12 05:32, Ben Hutchings wrote:
>>>> On Mon, 2012-05-28 at 18:31 +0100, Torne (Richard Coles) wrote:
>>>>> From: "Torne (Richard Coles)" <torne@google.com>
>>>>>
>>>>> MMC CSD info can specify very large, ridiculous timeouts, big enough to
>>>>> overflow timeout_ns on 32-bit machines. This can result in the card
>>>>> timing out on every operation because the wrapped timeout value is far
>>>>> too small.
>>>>>
>>>>> Fix the overflow by capping the result at 2 seconds. Cards specifying
>>>>> longer timeouts are almost certainly insane, and host controllers
>>>>> generally cannot support timeouts that long in any case.
>>>>>
>>>>> 2 seconds should be plenty of time for any card to actually function;
>>>>> the timeout calculation code is already using 1 second as a "worst case"
>>>>> timeout for cards running in SPI mode.
>>>>
>>>> Needs a 'Signed-off-by'.
>>>>
>>>>> ---
>>>>> drivers/mmc/core/core.c | 11 ++++++++++-
>>>>> 1 files changed, 10 insertions(+), 1 deletions(-)
>>>>>
>>>>> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
>>>>> index 0b6141d..3b4a9fc 100644
>>>>> --- a/drivers/mmc/core/core.c
>>>>> +++ b/drivers/mmc/core/core.c
>>>>> @@ -512,7 +512,16 @@ void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card)
>>>>> if (data->flags & MMC_DATA_WRITE)
>>>>> mult <<= card->csd.r2w_factor;
>>>>>
>>>>> - data->timeout_ns = card->csd.tacc_ns * mult;
>>>>> + /*
>>>>> + * The timeout in nanoseconds may overflow with some cards. Cap it at
>>>>> + * two seconds both to avoid the overflow and also because host
>>>>> + * controllers cannot generally generate timeouts that long anyway.
>>>>> + */
>>>>> + if (card->csd.tacc_ns <= (2 * NSEC_PER_SEC) / mult)
>>>>> + data->timeout_ns = card->csd.tacc_ns * mult;
>>>>> + else
>>>>> + data->timeout_ns = 2 * NSEC_PER_SEC;
>>>>
>>>> We clearly need to guard against overflow here, and this is the correct
>>>> way to clamp the multiplication. I can't speak as to whether 2 seconds
>>>> is the right limit.
>>>
>>> The host controllers I have looked at have a limit of around 2.5 seconds.
>>>
>>> But why not just use the size of the type as the limit? e.g.
>>>
>>> if (card->csd.tacc_ns <= UINT_MAX / mult)
>>> data->timeout_ns = card->csd.tacc_ns * mult;
>>> else
>>> data->timeout_ns = UINT_MAX;
>>
>> The host controller drivers don't seem to all do a very good job of
>> preventing further overflows or handling large values correctly
>> (though some do). sdhci takes the especially annoying additional step
>> of printk'ing a warning for *every single MMC command* where
>> data->timeout_ns is larger than the controller can accommodate.
>> Capping it to a value with a sensible order of magnitude seems to make
>> it more likely that cards with obviously bogus CSD parameters will
>> actually work. I don't object to using a larger number for the limit,
>> but UINT_MAX on a 64-bit system obviously doesn't limit this at all
>> and will leave you with timeouts up to 17 minutes, which seems
>> ridiculous :)
>
> Er, not 17 minutes; 102.4 seconds as I used later in my mail. SD cards
> have their timeouts capped already, so their larger 100x multiplier is
> not a problem; 102.4 seconds is the longest for an MMC card.
>

Linux is LP64. i.e. "int" is always 32-bit in the kernel

>> My original motivation for this patch is that I have a device with an
>> eMMC that specifies a 25.5 second timeout, attached to a sdhci host
>> whose maximum timeout is 2.8 seconds. Originally I proposed a patch to
>> just remove the warning in sdhci, but nobody replied, and when I
>> realised there was actually an overflow happening I opted to fix that
>> instead.
>>
>> So, yeah, we could use UINT_MAX, but then at minimum I also need to
>> kill the warning in sdhci to make my device work, and probably all the
>> host controller drivers need to be checked to make sure they don't use
>> timeout_ns in a way that can overflow.
>>
>> I've also just noticed that struct mmc_data's comment for timeout_ns
>> says /* data timeout (in ns, max 80ms) */ which is not true (the max
>> is 102.4 seconds if my math is correct), which may have contributed to
>> the host drivers not being too careful :)
>>
>> What do you think?

If you can identify the card, the you could make a new quirk in a fashion
similar to mmc_card_long_read_time().

Alternatively you could make use of SDHCI_QUIRK_BROKEN_TIMEOUT_VAL or
introduce your own sdhci quirk to suppress the warning.

>>
>>>>
>>>> Ben.
>>>>
>>>>> data->timeout_clks = card->csd.tacc_clks * mult;
>>>>>
>>>>> /*
>>>>
>>>
>>
>>
>>
>> --
>> Torne (Richard Coles)
>> torne@google.com
>
>
>



\
 
 \ /
  Last update: 2012-06-01 12:41    [W:0.075 / U:0.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site