Messages in this thread | | | Subject | Re: [PATCH -v4 2/2] PCIe: Add PCIe runtime D3cold support | From | Huang Ying <> | Date | Thu, 31 May 2012 08:40:25 +0800 |
| |
On Wed, 2012-05-30 at 23:49 +0200, Rafael J. Wysocki wrote: > On Tuesday, May 22, 2012, Rafael J. Wysocki wrote: > > On Friday, May 18, 2012, Huang Ying wrote: > > > This patch adds runtime D3cold support to PCIe bus. D3cold is the > > > deepest power saving state for PCIe devices. Where the main PCIe link > > > will be powered off totally, so before the PCIe main link is powered > > > on again, you can not access the device, even the configuration space, > > > which is still accessible in D3hot. Because the main PCIe link is not > > > available, the PCI PM registers can not be used to put device into/out > > > of D3cold state, that will be done by platform logic such as ACPI > > > _PR3. > > > > > > To support remote wake up in D3cold, aux power is supplied, and a > > > side-band pin: WAKE# is used to notify remote wake up event, the pin > > > is usually connected to platform logic such as ACPI GPE. This is > > > quite different with other power saving states, where remote wake up > > > is notified via PME message through the PCIe main link. > > > > > > PCIe devices in plug-in slot usually has no direct platform logic, for > > > example, there is usually no ACPI _PR3 for them. The D3cold support > > > for these devices can be done via the PCIe port connected to it. When > > > power on/off the PCIe port, the corresponding PCIe devices are powered > > > on/off too. And the remote wake up event from PCIe device will be > > > notified to the corresponding PCIe port. > > > > > > The PCI subsystem D3cold support and corresponding ACPI platform > > > support is implemented in the patch. Including the support for PCIe > > > devices in plug-in slot. > > > > > > For more information about PCIe D3cold and corresponding ACPI support, > > > please refer to: > > > > > > - PCI Express Base Specification Revision 2.0 > > > - Advanced Configuration and Power Interface Specification Revision 5.0 > > > > > > Originally-by: Zheng Yan <zheng.z.yan@intel.com> > > > Signed-off-by: Huang Ying <ying.huang@intel.com> > > > > Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl> > > On a second thought ... > > > > --- > > > drivers/pci/pci-acpi.c | 23 +++++++- > > > drivers/pci/pci-driver.c | 3 + > > > drivers/pci/pci-sysfs.c | 29 ++++++++++ > > > drivers/pci/pci.c | 110 +++++++++++++++++++++++++++++++++++++---- > > > drivers/pci/pci.h | 1 > > > drivers/pci/pcie/portdrv_pci.c | 44 ++++++++++++++-- > > > include/linux/pci.h | 16 ++++- > > > 7 files changed, 205 insertions(+), 21 deletions(-) > > > > > > --- a/drivers/pci/pci-acpi.c > > > +++ b/drivers/pci/pci-acpi.c > > > @@ -48,6 +48,12 @@ static void pci_acpi_wake_dev(acpi_handl > > > if (event != ACPI_NOTIFY_DEVICE_WAKE || !pci_dev) > > > return; > > > > > > + if (pci_dev->current_state == PCI_D3cold) { > > > + pci_wakeup_event(pci_dev); > > > + pm_runtime_resume(&pci_dev->dev); > > > + return; > > > + } > > > + > > > if (!pci_dev->pm_cap || !pci_dev->pme_support > > > || pci_check_pme_status(pci_dev)) { > > > if (pci_dev->pme_poll) > > > @@ -187,10 +193,13 @@ acpi_status pci_acpi_remove_pm_notifier( > > > > > > static pci_power_t acpi_pci_choose_state(struct pci_dev *pdev) > > > { > > > - int acpi_state; > > > + int acpi_state, d_max; > > > > > > - acpi_state = acpi_pm_device_sleep_state(&pdev->dev, NULL, > > > - ACPI_STATE_D3); > > I wonder what tree this patch is against? The code above doesn't seem to > be present in the current mainline.
As stated in [PATCH -v4 0/2], This patchset is based on:
[PATCH -v2] ACPI, PM, Specify lowest allowed state for device sleep state
Which is sent to LKML separately.
Best Regards, Huang Ying
| |