lkml.org 
[lkml]   [2012]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v5 2/2] mmc: core: Support packed command for eMMC4.5 device
From
Hi Jeon,

Any update for splitting between the read and write packing?
I also have a few more comments:

> +static u8 mmc_blk_prep_packed_list(struct mmc_queue *mq, struct request
*req)
> +{
> + struct request_queue *q = mq->queue;
> + struct mmc_card *card = mq->card;
> + struct request *cur = req, *next = NULL;
> + struct mmc_blk_data *md = mq->data;
> + bool en_rel_wr = card->ext_csd.rel_param & EXT_CSD_WR_REL_PARAM_EN;
+ unsigned int req_sectors = 0, phys_segments = 0;
> + unsigned int max_blk_count, max_phys_segs;
> + u8 put_back = 0;
> + u8 max_packed_rw = 0;
> + u8 reqs = 0;
> +
> + mq->mqrq_cur->packed_num = MMC_PACKED_N_ZERO;
> +
> + if (!(md->flags & MMC_BLK_CMD23) ||
> + !card->ext_csd.packed_event_en)
> + goto no_packed;
> +
> + if ((rq_data_dir(cur) == READ) &&
> + (card->host->caps2 & MMC_CAP2_PACKED_RD))
> + max_packed_rw = card->ext_csd.max_packed_reads;
> + else if ((rq_data_dir(cur) == WRITE) &&
> + (card->host->caps2 & MMC_CAP2_PACKED_WR))
> + max_packed_rw = card->ext_csd.max_packed_writes;
> +
> + if (max_packed_rw == 0)
> + goto no_packed;
> +
> + if (mmc_req_rel_wr(cur) &&
> + (md->flags & MMC_BLK_REL_WR) &&
> + !en_rel_wr) {
> + goto no_packed;
> + }
> +
> + max_blk_count = min(card->host->max_blk_count,
> + card->host->max_req_size >> 9);
> + if (unlikely(max_blk_count > 0xffff))
> + max_blk_count = 0xffff;
> +
> + max_phys_segs = queue_max_segments(q);
> + req_sectors += blk_rq_sectors(cur);
> + phys_segments += req->nr_phys_segments;
It would be best to change req to cur. This is the only place you use req,
in all other places you refer to cur.

> @@ -1291,10 +1657,42 @@ static int mmc_blk_issue_rw_rq(struct mmc_queue
*mq, struct request *rqc)
> * A block was successfully transferred.
> */
> mmc_blk_reset_success(md, type);
> - spin_lock_irq(&md->lock);
> - ret = __blk_end_request(req, 0,
> +
> + if (mq_rq->packed_cmd != MMC_PACKED_NONE) {
> + int idx = mq_rq->packed_fail_idx, i = 0;
> + ret = 0;
> + while (!list_empty(&mq_rq->packed_list)) {
> + prq = list_entry_rq(
> + mq_rq->packed_list.next);
> + if (idx == i) {
> + /* retry from error index */
> + mq_rq->packed_num -= idx;
> + mq_rq->req = prq;
> + ret = 1;
> + break;
> + }
> + list_del_init(&prq->queuelist);
> + spin_lock_irq(&md->lock);
> + __blk_end_request(prq, 0,
> + blk_rq_bytes(prq));
> + spin_unlock_irq(&md->lock);
> + i++;
> + }
> + if (mq_rq->packed_num == MMC_PACKED_N_SINGLE) {
> + prq = list_entry_rq(
> + mq_rq->packed_list.next);
You already get the prq inside the while. There is no need to do it again.


> @@ -1329,6 +1727,8 @@ static int mmc_blk_issue_rw_rq(struct mmc_queue
*mq,
> struct request *rqc)
> break;
> if (err == -ENODEV)
> goto cmd_abort;
> + if (mq_rq->packed_cmd != MMC_PACKED_NONE)
> + break;
This can cause an endless loop in case of MMC_BLK_DATA_ERR. The same
packed command will be sent over and over again without a beaking point.

Thanks,
Maya Erez
Consultant for Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum







\
 
 \ /
  Last update: 2012-04-26 14:25    [W:0.968 / U:0.544 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site