lkml.org 
[lkml]   [2012]   [Apr]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 06/12] USB: ohci-at91: change maximum number of ports
On 03/29/2012 05:04 PM, Alan Stern :
> On Thu, 29 Mar 2012, Nicolas Ferre wrote:
>
>> Change number of ports to 3 for newer SoCs. Modify pdata structure
>> and ohci-at91 code that was dealing with ports information and check
>> of port indexes.
>>
>> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
>> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>> ---
>> arch/arm/mach-at91/include/mach/board.h | 13 +++++++------
>> drivers/usb/host/ohci-at91.c | 22 +++++++++++++---------
>> 2 files changed, 20 insertions(+), 15 deletions(-)
>>
>> diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
>> index 544a5d5..49a8211 100644
>> --- a/arch/arm/mach-at91/include/mach/board.h
>> +++ b/arch/arm/mach-at91/include/mach/board.h
>> @@ -86,14 +86,15 @@ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *d
>> extern void __init at91_add_device_eth(struct macb_platform_data *data);
>>
>> /* USB Host */
>> +#define AT91_MAX_USBH_PORTS 3
>> struct at91_usbh_data {
>> - u8 ports; /* number of ports on root hub */
>> - int vbus_pin[2]; /* port power-control pin */
>> - u8 vbus_pin_active_low[2];
>> + int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */
>> + int overcurrent_pin[AT91_MAX_USBH_PORTS];
>> + u8 ports; /* number of ports on root hub */
>> u8 overcurrent_supported;
>> - int overcurrent_pin[2];
>> - u8 overcurrent_status[2];
>> - u8 overcurrent_changed[2];
>> + u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS];
>> + u8 overcurrent_status[AT91_MAX_USBH_PORTS];
>> + u8 overcurrent_changed[AT91_MAX_USBH_PORTS];
>> };
>> extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
>> extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
>> diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c
>> index 1262532..cf9707d 100644
>> --- a/drivers/usb/host/ohci-at91.c
>> +++ b/drivers/usb/host/ohci-at91.c
>> @@ -240,7 +240,7 @@ ohci_at91_start (struct usb_hcd *hcd)
>>
>> static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable)
>> {
>> - if (port < 0 || port >= 2)
>> + if (port < 0 || port >= ARRAY_SIZE(pdata->vbus_pin))
>
> Here and below, it will be a lot clearer to write AT91_MAX_USBH_PORTS
> instead of ARRAY_SIZE(padata->...).
>
>> @@ -301,7 +301,11 @@ static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
>> case SetPortFeature:
>> if (wValue == USB_PORT_FEAT_POWER) {
>> dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
>> - ohci_at91_usb_set_power(pdata, wIndex - 1, 1);
>> + if (wIndex && wIndex <= ARRAY_SIZE(pdata->vbus_pin)) {
>> + ohci_at91_usb_set_power(pdata, wIndex - 1, 1);
>
> Here and throughout the hub_control routine, things will be a lot
> simpler if you decrement wIndex at the start of the SetPortFeature
> case. Same for ClearPortFeature and maybe also GetPortStatus.

Ok, I will modify it according to your sugestions in a v2 patch series.

Best regards,
--
Nicolas Ferre


\
 
 \ /
  Last update: 2012-04-02 12:23    [W:0.564 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site