lkml.org 
[lkml]   [2012]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 3/3] i2c-s3c2410: Add HDMIPHY quirk for S3C2440
On 18.04.2012 15:46, Wolfram Sang wrote:

>
>>>> Optional properties:
>>>> + - gpios: The order of the gpios should be the following: <SDA, SCL>.
>>>> + The gpio specifier depends on the gpio controller. Required in all cases
>>>> + except when "samsung,i2c-no-gpio" is also specified.
>>>> + - samsung,i2c-no-gpio: input/output lines of the controller are
>>>> + permanently wired to the respective client, there are no gpio
>>>> + lines that need to be configured to enable this controller
>>>
>>> Can't we just skip this property...
>>
>> All standard s3c-24x0 i2c controllers require gpio lines for proper operation,
>> so lack of the gpios property should be considered as an error. However there
>> is a special case of internal, embedded i2c controller which has no such gpio
>> lines at all.
>>
>>>> - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
>>>> specified, default value is 0.
>>>> - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
>>>> specified, the default value in Hz is 100000.
>>>> + - samsung,i2c-quirk-hdmiphy: Quirk for HDMI PHY block found on
>>>> + Exynos4 platform - reduce timeout and reset controller after each
>>>> + transfer
>>>
>>> ... and this one, if we declare a new compatible-entry for exynos4?
>>
>> It is not strictly related to Exynos4 SoCs. Exynos4 SoC has 8 standard s3c2440 style
>> i2c controllers and one additional, internal controller for HDMIPHY, which needs
>> some workarounds in the driver. Maybe the quirk should be named 'broken timeout
>> detection'
>
> I was wondering since you do what I suggested for platform devices already:
>
> + .name = "s3c2440-hdmiphy-i2c",
> + .driver_data = QUIRK_S3C2440 | QUIRK_HDMIPHY | QUIRK_NO_GPIO,


Here I've done it this way for compatibility with legacy driver and
board(s).

Device tree is new interface, and I thought that it would be better
to describe things explicitly and separately from device type.

Right now these properties are used only on S3C2440, but I don't
consider it highly unlikely to see these on S3C**** in future.

Tomasz had similar doubts when I've posted patch that checked these
quirks only for S3C2440:

http://permalink.gmane.org/gmane.linux.drivers.i2c/10305

Thus, I've chosen properties and not separate type.

It's easy to introduce compat string (see below), but given above
I'm afraid that we might end up adding -hdmiphy- variant for every
new version of i2c controller.


E.g.

diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
index c6670f9..b1d106e 100644
--- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
@@ -6,6 +6,8 @@ Required properties:
- compatible: value should be either of the following.
(a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
(b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+ (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
+ inside HDMIPHY block found on several samsung SoCs
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: interrupt number to the cpu.
@@ -13,18 +15,13 @@ Required properties:

Optional properties:
- gpios: The order of the gpios should be the following: <SDA, SCL>.
- The gpio specifier depends on the gpio controller. Required in all cases
- except when "samsung,i2c-no-gpio" is also specified.
- - samsung,i2c-no-gpio: input/output lines of the controller are
- permanently wired to the respective client, there are no gpio
- lines that need to be configured to enable this controller
+ The gpio specifier depends on the gpio controller. Required in all
+ cases except for "samsung,i2c-hdmiphy-i2c" whose input/output
+ lines are permanently wired to the respective client
- samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
specified, default value is 0.
- samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
specified, the default value in Hz is 100000.
- - samsung,i2c-quirk-hdmiphy: Quirk for HDMI PHY block found on
- Exynos4 platform - reduce timeout and reset controller after each
- transfer

Example:

diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
index 71438eb..bc82045 100644
--- a/drivers/i2c/busses/i2c-s3c2410.c
+++ b/drivers/i2c/busses/i2c-s3c2410.c
@@ -106,6 +106,8 @@ MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids);
static const struct of_device_id s3c24xx_i2c_match[] = {
{ .compatible = "samsung,s3c2410-i2c", .data = (void *)0 },
{ .compatible = "samsung,s3c2440-i2c", .data = (void *)QUIRK_S3C2440 },
+ { .compatible = "samsung,s3c2440-hdmiphy-i2c",
+ .data = (void *)(QUIRK_S3C2440 | QUIRK_HDMIPHY | QUIRK_NO_GPIO) },
{},
};
MODULE_DEVICE_TABLE(of, s3c24xx_i2c_match);
@@ -902,12 +904,6 @@ s3c24xx_i2c_parse_dt(struct device_node *np, struct s3c24xx_i2c *i2c)

pdata->bus_num = -1; /* i2c bus number is dynamically assigned */

- if (of_get_property(np, "samsung,i2c-quirk-hdmiphy", NULL))
- i2c->quirks |= QUIRK_HDMIPHY;
-
- if (of_get_property(np, "samsung,i2c-no-gpio", NULL))
- i2c->quirks |= QUIRK_NO_GPIO;
-
of_property_read_u32(np, "samsung,i2c-sda-delay", &pdata->sda_delay);
of_property_read_u32(np, "samsung,i2c-slave-addr", &pdata->slave_addr);
of_property_read_u32(np, "samsung,i2c-max-bus-freq",

Regards,
--
Karol Lewandowski | Samsung Poland R&D Center | Linux/Platform

\
 
 \ /
  Last update: 2012-04-18 22:37    [W:0.058 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site