lkml.org 
[lkml]   [2012]   [Mar]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 12/14 v5] drm/i915/intel_i2c: use INDEX cycles for i2c read transactions
    Date
    It is very common for an i2c device to require a small 1 or 2 byte write
    followed by a read. For example, when reading from an i2c EEPROM it is
    common to write and address, offset or index followed by a reading some
    values.

    The i915 gmbus controller provides a special "INDEX" cycle for performing
    such a small write followed by a read. The INDEX can be either one or two
    bytes long. The advantage of using such a cycle is that the CPU has
    slightly less work to do once the read with INDEX cycle is started.

    Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
    ---
    drivers/gpu/drm/i915/intel_i2c.c | 32 ++++++++++++++++++++++++++++++--
    1 files changed, 30 insertions(+), 2 deletions(-)

    diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c
    index 25f2c9e..cb1db10 100644
    --- a/drivers/gpu/drm/i915/intel_i2c.c
    +++ b/drivers/gpu/drm/i915/intel_i2c.c
    @@ -204,13 +204,15 @@ intel_gpio_setup(struct intel_gmbus *bus, u32 pin)
    }

    static int
    -gmbus_xfer_read(struct drm_i915_private *dev_priv, struct i2c_msg *msg)
    +gmbus_xfer_read(struct drm_i915_private *dev_priv, struct i2c_msg *msg,
    + u32 gmbus1)
    {
    int reg_offset = dev_priv->gpio_mmio_base;
    u16 len = msg->len;
    u8 *buf = msg->buf;

    I915_WRITE(GMBUS1 + reg_offset,
    + gmbus1 |
    GMBUS_CYCLE_WAIT |
    (len << GMBUS_BYTE_COUNT_SHIFT) |
    (msg->addr << GMBUS_SLAVE_ADDR_SHIFT) |
    @@ -300,8 +302,34 @@ gmbus_xfer(struct i2c_adapter *adapter,
    I915_WRITE(GMBUS0 + reg_offset, bus->reg0);

    for (i = 0; i < num; i++) {
    + bool last = i + 1 == num;
    + u32 gmbus1 = 0;
    + u32 gmbus5 = 0;
    +
    + /*
    + * The gmbus controller can combine a 1 or 2 byte write with a
    + * read that immediately follows it by using an "INDEX" cycle.
    + */
    + if (!last &&
    + !(msgs[i].flags & I2C_M_RD) &&
    + (msgs[i + 1].flags & I2C_M_RD) &&
    + msgs[i].len <= 2) {
    + if (msgs[i].len == 2)
    + gmbus5 = GMBUS_2BYTE_INDEX_EN |
    + msgs[i].buf[1] |
    + (msgs[i].buf[0] << 8);
    + if (msgs[i].len == 1)
    + gmbus1 = GMBUS_CYCLE_INDEX |
    + (msgs[i].buf[0] <<
    + GMBUS_SLAVE_INDEX_SHIFT);
    + i += 1; /* set i to the index of the read xfer */
    + }
    +
    + /* GMBUS5 holds 16-bit index, but must be 0 if not used */
    + I915_WRITE(GMBUS5 + reg_offset, gmbus5);
    +
    if (msgs[i].flags & I2C_M_RD)
    - ret = gmbus_xfer_read(dev_priv, &msgs[i]);
    + ret = gmbus_xfer_read(dev_priv, &msgs[i], gmbus1);
    else
    ret = gmbus_xfer_write(dev_priv, &msgs[i]);

    --
    1.7.7.3


    \
     
     \ /
      Last update: 2012-03-28 14:57    [W:0.022 / U:60.976 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site