lkml.org 
[lkml]   [2012]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 01/11 v3] drm/i915/intel_i2c: cleanup
On Mon, Mar 26, 2012 at 10:26:40PM +0800, Daniel Kurtz wrote:
> 80 col, spaces around operators and other basic cleanup.
> Some info message cleanup.
>
> Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>

On reconsideration, nacked. You desperately try to squeeze a function with
already 5 indent levels (not counting indentation due to function
arguments and overflow) with already 100+ lines of code into 80 columns.

Please do the right thing and split out a few of helper functions. I
suggest you split out the read and write code, i.e.

if (msgs[i].flags & I2C_M_RD)
gmbus_xfer_read()
else
gmbus_xfer_write

This way you get 3 levels of tab space of room and I won't have to
complain as much that some of your later patches make gmbus_xfer way too
bug.

Yours, Daniel

> ---
> drivers/gpu/drm/i915/intel_i2c.c | 32 +++++++++++++++++++++-----------
> 1 files changed, 21 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c
> index 0713cc2..86b1861 100644
> --- a/drivers/gpu/drm/i915/intel_i2c.c
> +++ b/drivers/gpu/drm/i915/intel_i2c.c
> @@ -230,13 +230,16 @@ gmbus_xfer(struct i2c_adapter *adapter,
> (len << GMBUS_BYTE_COUNT_SHIFT) |
> (msgs[i].addr << GMBUS_SLAVE_ADDR_SHIFT) |
> GMBUS_SLAVE_READ | GMBUS_SW_RDY);
> - POSTING_READ(GMBUS2+reg_offset);
> + POSTING_READ(GMBUS2 + reg_offset);
> do {
> u32 val, loop = 0;
>
> - if (wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_RDY), 50))
> + if (wait_for(I915_READ(GMBUS2 + reg_offset) &
> + (GMBUS_SATOER | GMBUS_HW_RDY),
> + 50))
> goto timeout;
> - if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER)
> + if (I915_READ(GMBUS2 + reg_offset) &
> + GMBUS_SATOER)
> goto clear_err;
>
> val = I915_READ(GMBUS3 + reg_offset);
> @@ -260,12 +263,15 @@ gmbus_xfer(struct i2c_adapter *adapter,
> (msgs[i].len << GMBUS_BYTE_COUNT_SHIFT) |
> (msgs[i].addr << GMBUS_SLAVE_ADDR_SHIFT) |
> GMBUS_SLAVE_WRITE | GMBUS_SW_RDY);
> - POSTING_READ(GMBUS2+reg_offset);
> + POSTING_READ(GMBUS2 + reg_offset);
>
> while (len) {
> - if (wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_RDY), 50))
> + if (wait_for(I915_READ(GMBUS2 + reg_offset) &
> + (GMBUS_SATOER | GMBUS_HW_RDY),
> + 50))
> goto timeout;
> - if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER)
> + if (I915_READ(GMBUS2 + reg_offset) &
> + GMBUS_SATOER)
> goto clear_err;
>
> val = loop = 0;
> @@ -274,11 +280,14 @@ gmbus_xfer(struct i2c_adapter *adapter,
> } while (--len && ++loop < 4);
>
> I915_WRITE(GMBUS3 + reg_offset, val);
> - POSTING_READ(GMBUS2+reg_offset);
> + POSTING_READ(GMBUS2 + reg_offset);
> }
> }
>
> - if (i + 1 < num && wait_for(I915_READ(GMBUS2 + reg_offset) & (GMBUS_SATOER | GMBUS_HW_WAIT_PHASE), 50))
> + if (i + 1 < num &&
> + wait_for(I915_READ(GMBUS2 + reg_offset) &
> + (GMBUS_SATOER | GMBUS_HW_WAIT_PHASE),
> + 50))
> goto timeout;
> if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER)
> goto clear_err;
> @@ -300,14 +309,15 @@ done:
> * till then let it sleep.
> */
> if (wait_for((I915_READ(GMBUS2 + reg_offset) & GMBUS_ACTIVE) == 0, 10))
> - DRM_INFO("GMBUS timed out waiting for idle\n");
> + DRM_INFO("GMBUS [%s] timed out waiting for idle\n",
> + bus->adapter.name);
> I915_WRITE(GMBUS0 + reg_offset, 0);
> ret = i;
> goto out;
>
> timeout:
> - DRM_INFO("GMBUS timed out, falling back to bit banging on pin %d [%s]\n",
> - bus->reg0 & 0xff, bus->adapter.name);
> + DRM_INFO("GMBUS [%s] timed out, falling back to bit banging on pin %d\n",
> + bus->adapter.name, bus->reg0 & 0xff);
> I915_WRITE(GMBUS0 + reg_offset, 0);
>
> /* Hardware may not support GMBUS over these pins? Try GPIO bitbanging instead. */
> --
> 1.7.7.3
>

--
Daniel Vetter
Mail: daniel@ffwll.ch
Mobile: +41 (0)79 365 57 48


\
 
 \ /
  Last update: 2012-03-26 17:31    [W:0.109 / U:1.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site