lkml.org 
[lkml]   [2012]   [Feb]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4/6] sep: update initialisation
Date
From: Mark A. Allyn <mark.a.allyn@intel.com>

In particular we want to always do the reconfigure

[This is picked out of the differences between the upstream driver and
the staging driver. I'm resolving the differences as a series of updates -AC]

Signed-off-by: Alan Cox <alan@linux.intel.com>
---

drivers/staging/sep/sep_main.c | 26 +++++++++++++-------------
1 files changed, 13 insertions(+), 13 deletions(-)


diff --git a/drivers/staging/sep/sep_main.c b/drivers/staging/sep/sep_main.c
index 1fcabca..db51895 100644
--- a/drivers/staging/sep/sep_main.c
+++ b/drivers/staging/sep/sep_main.c
@@ -4150,7 +4150,6 @@ static int __devinit sep_probe(struct pci_dev *pdev,

dev_dbg(&sep->pdev->dev, "sep probe: PCI obtained, "
"device being prepared\n");
- dev_dbg(&sep->pdev->dev, "revision is %d\n", sep->pdev->revision);

/* Set up our register area */
sep->reg_physical_addr = pci_resource_start(sep->pdev, 0);
@@ -4213,38 +4212,39 @@ static int __devinit sep_probe(struct pci_dev *pdev,
goto end_function_deallocate_sep_shared_area;

/* The new chip requires a shared area reconfigure */
- if (sep->pdev->revision != 0) { /* Only for new chip */
- error = sep_reconfig_shared_area(sep);
- if (error)
- goto end_function_free_irq;
- }
+ error = sep_reconfig_shared_area(sep);
+ if (error)
+ goto end_function_free_irq;

sep->in_use = 1;

/* Finally magic up the device nodes */
/* Register driver with the fs */
error = sep_register_driver_with_fs(sep);
- if (error)
+
+ if (error) {
+ dev_err(&sep->pdev->dev, "error registering dev file\n");
goto end_function_free_irq;
+ }

+ sep->in_use = 0; /* through touching the device */
#ifdef SEP_ENABLE_RUNTIME_PM
pm_runtime_put_noidle(&sep->pdev->dev);
pm_runtime_allow(&sep->pdev->dev);
pm_runtime_set_autosuspend_delay(&sep->pdev->dev,
SUSPEND_DELAY);
pm_runtime_use_autosuspend(&sep->pdev->dev);
+ pm_runtime_mark_last_busy(&sep->pdev->dev);
sep->power_save_setup = 1;
#endif
-
- sep->in_use = 0;
-
/* register kernel crypto driver */
+#if defined(CONFIG_CRYPTO)
error = sep_crypto_setup();
if (error) {
- dev_dbg(&sep->pdev->dev, "crypto setup fail\n");
+ dev_err(&sep->pdev->dev, "crypto setup failed\n");
goto end_function_free_irq;
}
-
+#endif
goto end_function;

end_function_free_irq:
@@ -4292,7 +4292,7 @@ static void sep_remove(struct pci_dev *pdev)

/* Free the shared area */
sep_unmap_and_free_shared_area(sep_dev);
- iounmap((void __iomem *)sep_dev->reg_addr);
+ iounmap(sep_dev->reg_addr);

#ifdef SEP_ENABLE_RUNTIME_PM
if (sep->in_use) {


\
 
 \ /
  Last update: 2012-02-10 14:41    [W:0.050 / U:6.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site