lkml.org 
[lkml]   [2012]   [Dec]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 3/6] ACPI: Restructure movablecore_map with memory info from SRAT.
On 12/26/2012 02:53 PM, Yasuaki Ishimatsu wrote:
> Hi Tang,
>
> I don't think it can work well.
> The patch gets memory range of hotpluggable memory by
> acpi_numa_memory_affinity_init(). But it too late.
> For example, if we use log_buf_len boot options, memblock allocator
> runs before getting SRAT information. In this case, this movablecore_map
> boot option does not work well.
>

Hi Ishimatsu-san,

Yes, you are right. After finish_e820_parsing() in setup_arch(),
memblock allocator could start to work. So we need to reserve
the hotpluggable memory before it. But SRAT parsing is far behind.
So for now, I didn't work out a suitable way to do this.

I think we need to move ACPI table parsing logic before memblock is
ready. But we need to solve how to allocate memory for ACPI table
parsing logic.

I'll try to figure out a way and start a discussion soon.

Thanks. :)

> Thanks,
> Yasuaki Ishimatsu
>
> 2012/12/19 18:11, Tang Chen wrote:
>> The Hot Plugable bit in SRAT flags specifys if the memory range
>> could be hotplugged.
>>
>> If user specified movablecore_map=nn[KMG]@ss[KMG], reset
>> movablecore_map.map to the intersection of hotpluggable ranges from
>> SRAT and old movablecore_map.map.
>> Else if user specified movablecore_map=acpi, just use the hotpluggable
>> ranges from SRAT.
>> Otherwise, do nothing. The kernel will use all the memory in all nodes
>> evenly.
>>
>> The idea "getting info from SRAT" was from Liu Jiang<jiang.liu@huawei.com>.
>> And the idea "do more limit for memblock" was from Wu Jianguo<wujianguo@huawei.com>
>>
>> Signed-off-by: Tang Chen<tangchen@cn.fujitsu.com>
>> Tested-by: Gu Zheng<guz.fnst@cn.fujitsu.com>
>> ---
>> arch/x86/mm/srat.c | 55 +++++++++++++++++++++++++++++++++++++++++++++++++--
>> 1 files changed, 52 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/x86/mm/srat.c b/arch/x86/mm/srat.c
>> index 4ddf497..a8856d2 100644
>> --- a/arch/x86/mm/srat.c
>> +++ b/arch/x86/mm/srat.c
>> @@ -146,7 +146,12 @@ int __init
>> acpi_numa_memory_affinity_init(struct acpi_srat_mem_affinity *ma)
>> {
>> u64 start, end;
>> + u32 hotpluggable;
>> int node, pxm;
>> +#ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP
>> + int overlap;
>> + unsigned long start_pfn, end_pfn;
>> +#endif /* CONFIG_HAVE_MEMBLOCK_NODE_MAP */
>>
>> if (srat_disabled())
>> return -1;
>> @@ -157,8 +162,10 @@ acpi_numa_memory_affinity_init(struct acpi_srat_mem_affinity *ma)
>> if ((ma->flags& ACPI_SRAT_MEM_ENABLED) == 0)
>> return -1;
>>
>> - if ((ma->flags& ACPI_SRAT_MEM_HOT_PLUGGABLE)&& !save_add_info())
>> + hotpluggable = ma->flags& ACPI_SRAT_MEM_HOT_PLUGGABLE;
>> + if (hotpluggable&& !save_add_info())
>> return -1;
>> +
>> start = ma->base_address;
>> end = start + ma->length;
>> pxm = ma->proximity_domain;
>> @@ -178,9 +185,51 @@ acpi_numa_memory_affinity_init(struct acpi_srat_mem_affinity *ma)
>>
>> node_set(node, numa_nodes_parsed);
>>
>> - printk(KERN_INFO "SRAT: Node %u PXM %u [mem %#010Lx-%#010Lx]\n",
>> + printk(KERN_INFO "SRAT: Node %u PXM %u [mem %#010Lx-%#010Lx] %s\n",
>> node, pxm,
>> - (unsigned long long) start, (unsigned long long) end - 1);
>> + (unsigned long long) start, (unsigned long long) end - 1,
>> + hotpluggable ? "Hot Pluggable": "");
>> +
>> +#ifdef CONFIG_HAVE_MEMBLOCK_NODE_MAP
>> + start_pfn = PFN_DOWN(start);
>> + end_pfn = PFN_UP(end);
>> +
>> + if (!hotpluggable) {
>> + /* Clear the range overlapped in movablecore_map.map */
>> + remove_movablecore_map(start_pfn, end_pfn);
>> + goto out;
>> + }
>> +
>> + if (!movablecore_map.acpi) {
>> + for (overlap = 0; overlap< movablecore_map.nr_map; overlap++) {
>> + if (start_pfn< movablecore_map.map[overlap].end_pfn)
>> + break;
>> + }
>> +
>> + /*
>> + * If there is no overlapped range, or the end of the overlapped
>> + * range is higher than end_pfn, then insert nothing.
>> + */
>> + if (end_pfn<= movablecore_map.map[overlap].end_pfn)
>> + goto out;
>> +
>> + /*
>> + * Otherwise, insert the rest of this range to prevent memblock
>> + * from allocating memory in it.
>> + */
>> + start_pfn = movablecore_map.map[overlap].end_pfn;
>> + start = start_pfn>> PAGE_SHIFT;
>> + }
>> +
>> + /* If user chose to use SRAT info, insert the range anyway. */
>> + if (insert_movablecore_map(start_pfn, end_pfn))
>> + pr_err("movablecore_map: too many entries;"
>> + " ignoring [mem %#010llx-%#010llx]\n",
>> + (unsigned long long) start,
>> + (unsigned long long) (end - 1));
>> +
>> +out:
>> +#endif /* CONFIG_HAVE_MEMBLOCK_NODE_MAP */
>> return 0;
>> }
>>
>>
>
>
>



\
 
 \ /
  Last update: 2012-12-26 09:21    [W:0.091 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site