lkml.org 
[lkml]   [2012]   [Jan]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Regression: sky2 kernel between 3.1 and 3.2.1 (last known good 3.0.9)
On 1/20/2012 11:44 AM, Michael Breuer wrote:
> On 1/20/2012 11:26 AM, Stephen Hemminger wrote:
>> On Mon, 16 Jan 2012 11:39:13 -0500
>> Michael Breuer<mbreuer@majjas.com> wrote:
>>
>>> Synopsis:
>>>
>>> Receiving DMAR and other errors after approximately three days of
>>> uptime. The symptoms exactly match errors seen and then fixed around
>>> 2.6.32.4.
>>>
>>> While the system remains unaffected for too long to do a bisect, I was
>>> able to confirm that the problem exists in the 3.1 stable branch (I
>>> jumped from 3.0 to 3.2 when 3.2. was released).
>>>
>>> For now I reverted to the sky2.c from 3.0.9 and am running the rest of
>>> the kernel from 3.1.2, but won't be certain that this works until later
>>> in the week.
>>>
>>> Note that 20 seconds prior to the log extract below were DHCP renewal
>>> attempts on eth1, the issue below was on eth0. Not sure it's relevant,
>>> however back in 2010 a preceding DHCP event did turn out to be relevant
>>> to the manifestation of the bug.
>>>
>>> The 3.2.1-dirty I'm running is from git with a single local patch - for
>>> sidewinder force-feedback support (shouldn't be relevant to the sky2
>>> issue).
>>>
>>> Log extract:
>>>
>>> Jan 16 05:49:46 mail kernel: [198230.628919] DRHD: handling fault
>>> status
>>> reg 2
>>> [snip]
>>>
>>>
>>>
>>
>> Which exact chip version is this?
>> dmesg | grep sky2
>> lspci
> [ 9.927143] sky2: driver version 1.29
> [ 9.927166] sky2 0000:06:00.0: PCI INT A -> GSI 18 (level, low) ->
> IRQ 18
> [ 9.927177] sky2 0000:06:00.0: setting latency timer to 64
> [ 9.927254] sky2 0000:06:00.0: Yukon-2 EC Ultra chip revision 3
> [ 9.927339] sky2 0000:06:00.0: irq 71 for MSI/MSI-X
> [ 9.927562] sky2 0000:06:00.0: eth0: addr 00:26:18:00:1c:3b
> [ 9.927578] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) ->
> IRQ 17
> [ 9.927586] sky2 0000:04:00.0: setting latency timer to 64
> [ 9.927640] sky2 0000:04:00.0: Yukon-2 EC Ultra chip revision 3
> [ 9.927718] sky2 0000:04:00.0: irq 72 for MSI/MSI-X
> [ 9.927856] sky2 0000:04:00.0: eth1: addr 00:26:18:00:1c:3a
> [ 23.468135] sky2 0000:06:00.0: eth0: enabling interface
> [ 25.709668] sky2 0000:04:00.0: eth1: enabling interface
> [ 25.981841] sky2 0000:06:00.0: eth0: Link is up at 1000 Mbps, full
> duplex, fl ow control both
> [ 27.418742] sky2 0000:04:00.0: eth1: Link is up at 100 Mbps, full
> duplex, flo w control rx
>
> 04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056
> PCI-E Gigabit Ethernet Controller (rev 14)
> 05:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II
> Controller (rev b2)
> 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8056
> PCI-E Gigabit Ethernet Controller (rev 14)
>
Seems I spoke too soon... Got the sky2 crash again early this morning
after five days up.

Not sure how I can do any sort of bisect without narrowing down the
possible culprits.


\
 
 \ /
  Last update: 2012-01-21 16:31    [W:0.106 / U:4.984 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site