lkml.org 
[lkml]   [2011]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: BUG in kernel: Wrong Handling of USB HDD’s in scsiglue(slave configure) and scsi/sd(sd read cache type)
From
Thanks James, I got your point will look more on this.

Regards,
Amit Sahrawat

On Fri, Sep 30, 2011 at 11:41 PM, James Bottomley
<James.Bottomley@hansenpartnership.com> wrote:
> On Fri, 2011-09-30 at 23:26 +0530, Amit Sahrawat wrote:
>> Adding linux-usb - to get more insight's into the problem.
>>
>> On Fri, Sep 30, 2011 at 11:23 PM, Amit Sahrawat
>> <amit.sahrawat83@gmail.com> wrote:
>> > On Fri, Sep 30, 2011 at 5:48 PM, James Bottomley
>> > <James.Bottomley@hansenpartnership.com> wrote:
>> >> On Fri, 2011-09-30 at 12:26 +0530, Amit Sahrawat wrote:
>> >>> Now, for the USB HDD which do have write cache - sginfo is showing
>> >>> them to Write Cache Enabled as false.
>> >>> Why do the result of hdparm identification and sginfo varies- (I know
>> >>> they have different interface to work with and hdparm takes care of
>> >>> that by using SG_IO interface from it's code)? hdparm showed me
>> >>> correct results - that lead me to digging in the kernel code and
>> >>> checking the performance for USB HDD with Write cache enabled/disabled
>> >>> - which also showed that QUEUE ordering chosen for USB HDD is not
>> >>> correct.
>> >>
>> >> Well, what all this means is the SATL in the USB device is implemented
>> >> wrongly.  Since USB devices only preset SCSI interfaces, that's what we
>> >> have to believe.
>> >>
>> >> hdparm when used correctly sends an ATA inquiry command wrapped in an
>> >> ATA_12 or ATA_16 SCSI command.  A large number of legacy SATLs are known
>> >> to crash on these commands.
>> >>
>> >> Are you sure the ATA command is reporting correctly?  A write back cache
>> >> is a remarkably silly thing to enable for a USB device because they're
>> >> highly likely to be surprise ejected which powers the device down.
>> >>
>> > In addition to the problem reported - there is one more thing I have
>> > noticed with USB HDD - they should be shown as 'removable' but the
>> > removable is marked only for USB PEN Drives. This seems to be a bit of
>> > confusing, any mass storage media connected on USB port should be
>> > recognized as removable.
>
> I don't really think so.  Removable to sd means that the drive can be
> removed from the housing, not that the connector cable is hot plug so
> the whole disk can disappear.  I think your disk is the latter, and
> therefore removable probably isn't what you want (otherwise the sd
> driver will start probing for medium change and other things your device
> won't understand).
>
>> > So, for handling the issue, I would consider adding the handling in
>> > slave_configure()(usb/storage/scsiglue) which marks the HDD/pen drives
>> > as removable also signifying them to be USB based.
>> > Then, as part of sd_revalidation – how about adding the ATA_IDENTIFY
>> > command part if the device is USB HDD? As far as the result of
>> > ATA_IDENTIFY is concerned – they return proper ‘256’ bytes - response
>> > and the Words – 82, 85 used for feature supported and enabled/disabled
>> > returns proper values for the USB HDD’s I have seen. In case of USB
>> > pen drives – they return failure – I did not see any crash – maybe I
>> > don’t have one of the legacy SATL based disk.
>> > Since, I am new to this – I will check more on this to get a viable
>> > solution. Please add your opinion. Can you share the name of the
>> > device which causes crash with these ATA commands, If I am able to get
>> > one I can try on that also.
>
> How?  There are many USB devices whose SATL crashes and burns on ATA_12
> or ATA_16, so this would add fragility to the detection path. The
> detection path has to be cast iron because it has to work on a vast
> range of devices.  The only way this could really work is to add it in
> the usb storage driver and then replace the bad mode pages.
>
> James
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2011-09-30 20:33    [W:0.301 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site