lkml.org 
[lkml]   [2011]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V4] mtd: Add DiskOnChip G3 support
Date
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
- no flash writes/erases are implemented
- ECC fixes are not implemented
- powerdown is not implemented
- IPL handling is not yet done

On the brighter side, the chip reading does work.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>

---
Since V3:
- introduced cpu_relax()
- comment doc_delay() necessity
- remove debugfs ifdefery

Since V2:
- converted debug entries from sysfs to debugfs
- rebase on kernel 3.1.0-rc4

Since V1:
- more static functions, less global functions
- prevent BCH calculation over OTP/BBT area
- add bad blocks table support
- fix the number of available blocks on G3 M512 (2048
blocks)
- cleaner double plane handling (2 pages being necessary to
read 2 "virtual pages" of 512 bytes.
- select device 0 after each operation
Upon power failure or reboot, floor 0 needs to be
selected as IPL is only on floor 0.
- debug: add protection states reports
- convert to new mtd partition API
Effect of commit "mtd: introduce
mtd_device_(un)register()"
---
drivers/mtd/devices/Kconfig | 10 +
drivers/mtd/devices/Makefile | 1 +
drivers/mtd/devices/docg3.c | 1099 ++++++++++++++++++++++++++++++++++++++++++
drivers/mtd/devices/docg3.h | 237 +++++++++
4 files changed, 1347 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/devices/docg3.c
create mode 100644 drivers/mtd/devices/docg3.h

diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 35081ce..6d91a1f 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -249,6 +249,16 @@ config MTD_DOC2001PLUS
under "NAND Flash Device Drivers" (currently that driver does not
support all Millennium Plus devices).

+config MTD_DOCG3
+ tristate "M-Systems Disk-On-Chip G3"
+ ---help---
+ This provides an MTD device driver for the M-Systems DiskOnChip
+ G3 devices.
+
+ The driver provides access to G3 DiskOnChip, distributed by
+ M-Systems and now Sandisk. The support is very experimental,
+ and doesn't give access to any write operations.
+
config MTD_DOCPROBE
tristate
select MTD_DOCECC
diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile
index f3226b1..e71991f 100644
--- a/drivers/mtd/devices/Makefile
+++ b/drivers/mtd/devices/Makefile
@@ -5,6 +5,7 @@
obj-$(CONFIG_MTD_DOC2000) += doc2000.o
obj-$(CONFIG_MTD_DOC2001) += doc2001.o
obj-$(CONFIG_MTD_DOC2001PLUS) += doc2001plus.o
+obj-$(CONFIG_MTD_DOCG3) += docg3.o
obj-$(CONFIG_MTD_DOCPROBE) += docprobe.o
obj-$(CONFIG_MTD_DOCECC) += docecc.o
obj-$(CONFIG_MTD_SLRAM) += slram.o
diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c
new file mode 100644
index 0000000..99c1597
--- /dev/null
+++ b/drivers/mtd/devices/docg3.c
@@ -0,0 +1,1099 @@
+/*
+ * Handles the M-Systems DiskOnChip G3 chip
+ *
+ * Copyright (C) 2011 Robert Jarzmik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+
+#include "docg3.h"
+
+/*
+ * This driver handles the DiskOnChip G3 flash memory.
+ *
+ * As no specification is available from M-Systems/Sandisk, this drivers lacks
+ * several functions available on the chip, as :
+ * - block erase
+ * - page write
+ * - IPL write
+ * - ECC fixing (lack of BCH algorith understanding)
+ * - powerdown / powerup
+ *
+ * The bus data width (8bits versus 16bits) is not handled (if_cfg flag), and
+ * the driver assumes a 16bits data bus.
+ *
+ * DocG3 relies on 2 ECC algorithms, which are handled in hardware :
+ * - a 1 byte Hamming code stored in the OOB for each page
+ * - a 7 bytes BCH code stored in the OOB for each page
+ * The BCH part is only used for check purpose, no correction is available as
+ * some information is missing. What is known is that :
+ * - BCH is in GF(2^14)
+ * - BCH is over data of 520 bytes (512 page + 7 page_info bytes
+ * + 1 hamming byte)
+ * - BCH can correct up to 4 bits (t = 4)
+ * - BCH syndroms are calculated in hardware, and checked in hardware as well
+ *
+ */
+
+#define doc_readb(reg) \
+ __raw_readb(docg3->base + (reg));
+#define doc_writeb(value, reg) \
+do { \
+ doc_vdbg("Write %02x to register %04x\n", (value), (reg)); \
+ __raw_writeb((value), docg3->base + (reg)); \
+} while (0)
+#define doc_readw(reg) \
+ __raw_readw(docg3->base + (reg));
+#define doc_writew(value, reg) \
+do { \
+ doc_vdbg("Write %04x to register %04x\n", (value), (reg)); \
+ __raw_writew((value), docg3->base + (reg)); \
+} while (0)
+
+#define doc_flashCommand(cmd) \
+do { \
+ doc_dbg("doc_flashCommand: %02x " #cmd "\n", DoC_Cmd_##cmd); \
+ doc_writeb(DoC_Cmd_##cmd, DoC_FlashCommand); \
+} while (0)
+
+#define doc_flashSequence(seq) \
+do { \
+ doc_dbg("doc_flashSequence: %02x " #seq "\n", DoC_Seq_##seq); \
+ doc_writeb(DoC_Seq_##seq, DoC_FlashSequence); \
+} while (0)
+
+#define doc_flashAddress(addr) \
+do { \
+ doc_dbg("doc_flashAddress: %02x\n", (addr)); \
+ doc_writeb((addr), DoC_FlashAddress); \
+} while (0)
+
+static const char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL };
+
+static int doc_register_readb(struct docg3 *docg3, int reg)
+{
+ u8 val;
+
+ doc_writew(reg, DoC_ReadAddress);
+ val = doc_readb(reg);
+ doc_vdbg("Read register %04x : %02x\n", reg, val);
+ return val;
+}
+
+static int doc_register_readw(struct docg3 *docg3, int reg)
+{
+ u16 val;
+
+ doc_writew(reg, DoC_ReadAddress);
+ val = doc_readw(reg);
+ doc_vdbg("Read register %04x : %04x\n", reg, val);
+ return val;
+}
+
+/**
+ * doc_delay - delay docg3 operations
+ * @docg3: the device
+ * @nbNOPs: the number of NOPs to issue
+ *
+ * As no specification is available, the right timings between chip commands are
+ * unknown. The only available piece of information are the observed nops on a
+ * working docg3 chip.
+ * Therefore, doc_delay relies on a busy loop of NOPs, instead of scheduler
+ * friendlier msleep() functions or blocking mdelay().
+ */
+static void doc_delay(struct docg3 *docg3, int nbNOPs)
+{
+ int i;
+
+ doc_dbg("NOP x %d\n", nbNOPs);
+ for (i = 0; i < nbNOPs; i++)
+ doc_writeb(0, DoC_NOP);
+}
+
+static int is_prot_seq_error(struct docg3 *docg3)
+{
+ int ctrl;
+
+ ctrl = doc_register_readb(docg3, DoC_FlashControl);
+ return ctrl & (Doc_Ctrl_PROTECTION_ERROR | Doc_Ctrl_SEQUENCE_ERROR);
+}
+
+static int doc_is_ready(struct docg3 *docg3)
+{
+ int ctrl;
+
+ ctrl = doc_register_readb(docg3, DoC_FlashControl);
+ return ctrl & Doc_Ctrl_FLASHREADY;
+}
+
+static int doc_wait_ready(struct docg3 *docg3)
+{
+ int maxWaitCycles = 100;
+
+ do {
+ doc_delay(docg3, 4);
+ cpu_relax();
+ } while (!doc_is_ready(docg3) && maxWaitCycles--);
+ doc_delay(docg3, 2);
+ if (maxWaitCycles > 0)
+ return 0;
+ else
+ return -EIO;
+}
+
+static int doc_reset_seq(struct docg3 *docg3)
+{
+ int ret;
+
+ doc_writeb(0x10, DoC_FlashControl);
+ doc_flashSequence(RESET);
+ doc_flashCommand(RESET);
+ doc_delay(docg3, 2);
+ ret = doc_wait_ready(docg3);
+
+ doc_dbg("doc_reset_seq() -> isReady=%s\n", ret ? "false" : "true");
+ return ret;
+}
+
+/**
+ * doc_read_data_area - Read data from data area
+ * @docg3: the device
+ * @buf: the buffer to fill in
+ * @len: the lenght to read
+ * @first: first time read, DoC_ReadAddress should be set
+ *
+ * Reads bytes from flash data. Handles the single byte / even bytes reads.
+ */
+static void doc_read_data_area(struct docg3 *docg3, void *buf, int len,
+ int first)
+{
+ int i, cdr, len4;
+ u16 data16, *dst16;
+ u8 data8, *dst8;
+
+ doc_dbg("doc_read_data_area(buf=%p, len=%d)\n", buf, len);
+ cdr = len & 0x3;
+ len4 = len - cdr;
+
+ if (first)
+ doc_writew(DOC_IOSPACE_DATA, DoC_ReadAddress);
+ dst16 = buf;
+ for (i = 0; i < len4; i += 2) {
+ data16 = doc_readw(DOC_IOSPACE_DATA);
+ *dst16 = data16;
+ dst16++;
+ }
+
+ if (cdr) {
+ doc_writew(DOC_IOSPACE_DATA | Doc_ReadAddr_ONE_BYTE,
+ DoC_ReadAddress);
+ doc_delay(docg3, 1);
+ dst8 = (u8 *)dst16;
+ for (i = 0; i < cdr; i++) {
+ data8 = doc_readb(DOC_IOSPACE_DATA);
+ *dst8 = data8;
+ dst8++;
+ }
+ }
+}
+
+/**
+ * doc_set_data_mode - Sets the flash to reliable data mode
+ * @docg3: the device
+ *
+ * The reliable data mode is a bit slower than the fast mode, but less errors
+ * occur. Entering the reliable mode cannot be done without entering the fast
+ * mode first.
+ */
+static void doc_set_reliable_mode(struct docg3 *docg3)
+{
+ doc_dbg("doc_set_reliable_mode()\n");
+ doc_flashSequence(SET_MODE);
+ doc_flashCommand(FAST_MODE);
+ doc_flashCommand(RELIABLE_MODE);
+ doc_delay(docg3, 2);
+}
+
+/**
+ * doc_set_asic_mode - Set the ASIC mode
+ * @docg3: the device
+ * @mode: the mode
+ *
+ * The ASIC can work in 3 modes :
+ * - RESET: all registers are zeroed
+ * - NORMAL: receives and handles commands
+ * - POWERDOWN: minimal poweruse, flash parts shut off
+ */
+static void doc_set_asic_mode(struct docg3 *docg3, u8 mode)
+{
+ int i;
+
+ for (i = 0; i < 12; i++)
+ doc_readb(DOC_IOSPACE_IPL);
+
+ mode |= Doc_AsicMode_MDWREN;
+ doc_dbg("doc_set_asic_mode(%02x)\n", mode);
+ doc_writeb(mode, DoC_AsicMode);
+ doc_writeb(~mode, DoC_AsicModeConfirm);
+ doc_delay(docg3, 1);
+}
+
+/**
+ * doc_set_device_id - Sets the devices id for cascaded G3 chips
+ * @docg3: the device
+ * @id: the chip to select (amongst 0, 1, 2, 3)
+ *
+ * There can be 4 cascaded G3 chips. This function selects the one which will
+ * should be the active one.
+ */
+static void doc_set_device_id(struct docg3 *docg3, int id)
+{
+ u8 ctrl;
+
+ doc_dbg("doc_set_device_id(%d)\n", id);
+ doc_writeb(id, DoC_DeviceSelect);
+ ctrl = doc_register_readb(docg3, DoC_FlashControl);
+
+ ctrl &= ~Doc_Ctrl_Violation;
+ ctrl |= Doc_Ctrl_CE;
+ doc_writeb(ctrl, DoC_FlashControl);
+}
+
+/**
+ * doc_set_extra_page_mode - Change flash page layout
+ * @docg3: the device
+ *
+ * Normally, the flash page is split into the data (512 bytes) and the out of
+ * band data (16 bytes). For each, 4 more bytes can be accessed, where the wear
+ * leveling counters are stored. To access this last area of 4 bytes, a special
+ * mode must be input to the flash ASIC.
+ *
+ * Returns 0 if no error occured, -EIO else.
+ */
+static int doc_set_extra_page_mode(struct docg3 *docg3)
+{
+ int fctrl;
+
+ doc_dbg("doc_set_extra_page_mode()\n");
+ doc_flashSequence(PAGE_SIZE_532);
+ doc_flashCommand(PAGE_SIZE_532);
+ doc_delay(docg3, 2);
+
+ fctrl = doc_register_readb(docg3, DoC_FlashControl);
+ if (fctrl & (Doc_Ctrl_PROTECTION_ERROR | Doc_Ctrl_SEQUENCE_ERROR))
+ return -EIO;
+ else
+ return 0;
+}
+
+/**
+ * doc_seek - Set both flash planes to the specified block, page for reading
+ * @docg3: the device
+ * @block0: the first plane block index
+ * @block1: the second plane block index
+ * @page: the page index within the block
+ * @wear: if true, read will occur on the 4 extra bytes of the wear area
+ * @ofs: offset in page to read
+ *
+ * Programs the flash even and odd planes to the specific block and page.
+ * Alternatively, programs the flash to the wear area of the specified page.
+ */
+static int doc_read_seek(struct docg3 *docg3, int block0, int block1, int page,
+ int wear, int ofs)
+{
+ int sector, ret = 0;
+
+ doc_dbg("doc_seek(blocks=(%d,%d), page=%d, ofs=%d, wear=%d)\n",
+ block0, block1, page, ofs, wear);
+
+ if (!wear && (ofs < 2 * DOC_LAYOUT_PAGE_SIZE)) {
+ doc_flashSequence(SET_PLANE1);
+ doc_flashCommand(READ_PLANE1);
+ doc_delay(docg3, 2);
+ } else {
+ doc_flashSequence(SET_PLANE2);
+ doc_flashCommand(READ_PLANE2);
+ doc_delay(docg3, 2);
+ }
+
+ doc_set_reliable_mode(docg3);
+ if (wear)
+ ret = doc_set_extra_page_mode(docg3);
+ if (ret)
+ goto out;
+
+ sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
+ doc_flashSequence(READ);
+ doc_flashCommand(PROG_BLOCK_ADDR);
+ doc_delay(docg3, 1);
+ doc_flashAddress(sector & 0xff);
+ doc_flashAddress((sector >> 8) & 0xff);
+ doc_flashAddress((sector >> 16) & 0xff);
+ doc_delay(docg3, 1);
+
+ sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
+ doc_flashCommand(PROG_BLOCK_ADDR);
+ doc_delay(docg3, 1);
+ doc_flashAddress(sector & 0xff);
+ doc_flashAddress((sector >> 8) & 0xff);
+ doc_flashAddress((sector >> 16) & 0xff);
+ doc_delay(docg3, 2);
+
+out:
+ return ret;
+}
+
+/**
+ * doc_read_page_ecc_init - Initialize hardware ECC engine
+ * @docg3: the device
+ * @len: the number of bytes covered by the ECC (BCH covered)
+ *
+ * The function does initialize the hardware ECC engine to compute the Hamming
+ * ECC (on 1 byte) and the BCH Syndroms (on 7 bytes).
+ *
+ * Return 0 if succeeded, -EIO on error
+ */
+static int doc_read_page_ecc_init(struct docg3 *docg3, int len)
+{
+ doc_writew(Doc_ECCConf0_READ_MODE
+ | Doc_ECCConf0_BCH_ENABLE | Doc_ECCConf0_HAMMING_ENABLE
+ | (len & Doc_ECCConf0_DATA_BYTES_MASK),
+ DoC_EccConf0);
+ doc_delay(docg3, 4);
+ doc_register_readb(docg3, DoC_FlashControl);
+ return doc_wait_ready(docg3);
+}
+
+/**
+ * doc_read_page_prepare - Prepares reading data from a flash page
+ * @docg3: the device
+ * @block0: the first plane block index on flash memory
+ * @block1: the second plane block index on flash memory
+ * @page: the page index in the block
+ * @offset: the offset in the page (must be a multiple of 4)
+ *
+ * Prepares the page to be read in the flash memory :
+ * - tell ASIC to map the flash pages
+ * - tell ASIC to be in read mode
+ *
+ * After a call to this method, a call to doc_read_page_finish is mandatory,
+ * to end the read cycle of the flash.
+ *
+ * Read data from a flash page. The length to be read must be between 0 and
+ * (page_size + oob_size + wear_size), ie. 532, and a multiple of 4 (because
+ * the extra bytes reading is not implemented).
+ *
+ * As pages are grouped by 2 (in 2 planes), reading from a page must be done
+ * in two steps:
+ * - one read of 512 bytes at offset 0
+ * - one read of 512 bytes at offset 512 + 16
+ *
+ * Returns 0 if successful, -EIO if a read error occured.
+ */
+static int doc_read_page_prepare(struct docg3 *docg3, int block0, int block1,
+ int page, int offset)
+{
+ int wear_area = 0, ret = 0;
+
+ doc_dbg("doc_read_page_prepare(blocks=(%d,%d), page=%d, ofsInPage=%d)\n",
+ block0, block1, page, offset);
+ if (offset >= DOC_LAYOUT_WEAR_OFFSET)
+ wear_area = 1;
+ if (!wear_area && offset > (DOC_LAYOUT_PAGE_OOB_SIZE * 2))
+ return -EINVAL;
+
+ doc_set_device_id(docg3, docg3->device_id);
+ ret = doc_reset_seq(docg3);
+ if (ret)
+ goto err;
+
+ /* Program the flash address block and page */
+ ret = doc_read_seek(docg3, block0, block1, page, wear_area, offset);
+ if (ret)
+ goto err;
+
+ doc_flashCommand(READ_ALL_PLANES);
+ doc_delay(docg3, 2);
+ doc_wait_ready(docg3);
+
+ doc_flashCommand(SET_ADDR_READ);
+ doc_delay(docg3, 1);
+ if (offset >= DOC_LAYOUT_PAGE_SIZE * 2)
+ offset -= 2 * DOC_LAYOUT_PAGE_SIZE;
+ doc_flashAddress(offset >> 2);
+ doc_delay(docg3, 1);
+ doc_wait_ready(docg3);
+
+ doc_flashCommand(READ_FLASH);
+
+ return 0;
+err:
+ doc_writeb(0, DoC_DataEnd);
+ doc_delay(docg3, 2);
+ return -EIO;
+}
+
+/**
+ * doc_read_page_getbytes - Reads bytes from a prepared page
+ * @docg3: the device
+ * @len: the number of bytes to be read (must be a multiple of 4)
+ * @buf: the buffer to be filled in
+ * @first: 1 if first time read, DoC_ReadAddress should be set
+ *
+ */
+static int doc_read_page_getbytes(struct docg3 *docg3, int len, u_char *buf,
+ int first)
+{
+ doc_read_data_area(docg3, buf, len, first);
+ doc_delay(docg3, 2);
+ return len;
+}
+
+/**
+ * doc_get_hw_bch_syndroms - Get hardware calculated BCH syndroms
+ * @docg3: the device
+ * @syns: the array of 7 integers where the syndroms will be stored
+ */
+static void doc_get_hw_bch_syndroms(struct docg3 *docg3, int *syns)
+{
+ int i;
+
+ for (i = 0; i < DOC_ECC_BCH_SIZE; i++)
+ syns[i] = doc_register_readb(docg3, DoC_BCH_Syndrom(i));
+}
+
+/**
+ * doc_read_page_finish - Ends reading of a flash page
+ * @docg3: the device
+ *
+ * As a side effect, resets the chip selector to 0. This ensures that after each
+ * read operation, the floor 0 is selected. Therefore, if the systems halts, the
+ * reboot will boot on floor 0, where the IPL is.
+ */
+static void doc_read_page_finish(struct docg3 *docg3)
+{
+ doc_writeb(0, DoC_DataEnd);
+ doc_delay(docg3, 2);
+ doc_set_device_id(docg3, 0);
+}
+
+/**
+ * calc_block_sector - Calculate blocks, pages and ofs.
+
+ * @from: offset in flash
+ * @block0: first plane block index calculated
+ * @block1: second plane block index calculated
+ * @page: page calculated
+ * @ofs: offset in page
+ */
+static void calc_block_sector(loff_t from, int *block0, int *block1, int *page,
+ int *ofs)
+{
+ uint sector;
+
+ sector = from / DOC_LAYOUT_PAGE_SIZE;
+ *block0 = sector / (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_NBPLANES)
+ * DOC_LAYOUT_NBPLANES;
+ *block1 = *block0 + 1;
+ *page = sector % (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_NBPLANES);
+ *page /= DOC_LAYOUT_NBPLANES;
+ if (sector % 2)
+ *ofs = DOC_LAYOUT_PAGE_OOB_SIZE;
+ else
+ *ofs = 0;
+}
+
+/**
+ * doc_read - Read bytes from flash
+ * @mtd: the device
+ * @from: the offset from first block and first page, in bytes, aligned on page
+ * size
+ * @len: the number of bytes to read (must be a multiple of 4)
+ * @retlen: the number of bytes actually read
+ * @buf: the filled in buffer
+ *
+ * Reads flash memory pages. This function does not read the OOB chunk, but only
+ * the page data.
+ *
+ * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured
+ */
+static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct docg3 *docg3 = mtd->priv;
+ int block0, block1, page, readlen, ret, ofs = 0;
+ int syn[DOC_ECC_BCH_SIZE], eccconf1;
+ u8 oob[DOC_LAYOUT_OOB_SIZE];
+
+ ret = -EINVAL;
+ doc_dbg("doc_read(from=%lld, len=%u, buf=%p)\n", from, len, buf);
+ if (from % DOC_LAYOUT_PAGE_SIZE)
+ goto err;
+ if (len % 4)
+ goto err;
+ calc_block_sector(from, &block0, &block1, &page, &ofs);
+ if (block1 > docg3->max_block)
+ goto err;
+
+ *retlen = 0;
+ ret = 0;
+ readlen = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE);
+ while (!ret && len > 0) {
+ readlen = min_t(size_t, len, (size_t)DOC_LAYOUT_PAGE_SIZE);
+ ret = doc_read_page_prepare(docg3, block0, block1, page, ofs);
+ if (ret < 0)
+ goto err;
+ ret = doc_read_page_ecc_init(docg3, DOC_ECC_BCH_COVERED_BYTES);
+ if (ret < 0)
+ goto err_in_read;
+ ret = doc_read_page_getbytes(docg3, readlen, buf, 1);
+ if (ret < readlen)
+ goto err_in_read;
+ ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE,
+ oob, 0);
+ if (ret < DOC_LAYOUT_OOB_SIZE)
+ goto err_in_read;
+
+ *retlen += readlen;
+ buf += readlen;
+ len -= readlen;
+
+ ofs ^= DOC_LAYOUT_PAGE_OOB_SIZE;
+ if (ofs == 0)
+ page += 2;
+ if (page > DOC_ADDR_PAGE_MASK) {
+ page = 0;
+ block0 += 2;
+ block1 += 2;
+ }
+
+ /*
+ * There should be a BCH bitstream fixing algorithm here ...
+ * By now, a page read failure is triggered by BCH error
+ */
+ doc_get_hw_bch_syndroms(docg3, syn);
+ eccconf1 = doc_register_readb(docg3, DoC_EccConf1);
+
+ doc_dbg("OOB - INFO: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
+ oob[0], oob[1], oob[2], oob[3], oob[4],
+ oob[5], oob[6]);
+ doc_dbg("OOB - HAMMING: %02x\n", oob[7]);
+ doc_dbg("OOB - BCH_ECC: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
+ oob[8], oob[9], oob[10], oob[11], oob[12],
+ oob[13], oob[14]);
+ doc_dbg("OOB - UNUSED: %02x\n", oob[15]);
+ doc_dbg("ECC checks: ECCConf1=%x\n", eccconf1);
+ doc_dbg("ECC BCH syndrom: %02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
+ syn[0], syn[1], syn[2], syn[3], syn[4], syn[5], syn[6]);
+
+ ret = -EBADMSG;
+ if (block0 >= DOC_LAYOUT_BLOCK_FIRST_DATA) {
+ if (eccconf1 & Doc_ECCConf1_BCH_SYNDROM_ERR)
+ goto err_in_read;
+ if (is_prot_seq_error(docg3))
+ goto err_in_read;
+ }
+ doc_read_page_finish(docg3);
+ }
+
+ return 0;
+err_in_read:
+ doc_read_page_finish(docg3);
+err:
+ return ret;
+}
+
+/**
+ * doc_read_oob - Read out of band bytes from flash
+ * @mtd: the device
+ * @from: the offset from first block and first page, in bytes, aligned on page
+ * size
+ * @ops: the mtd oob structure
+ *
+ * Reads flash memory OOB area of pages.
+ *
+ * Returns 0 if read successfull, of -EIO, -EINVAL if an error occured
+ */
+static int doc_read_oob(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops)
+{
+ struct docg3 *docg3 = mtd->priv;
+ int block0, block1, page, ofs, ret;
+ u8 *buf = ops->oobbuf;
+ size_t len = ops->ooblen;
+
+ doc_dbg("doc_read_oob(from=%lld, buf=%p, len=%d)\n", from, buf, len);
+ if (len != DOC_LAYOUT_OOB_SIZE)
+ return -EINVAL;
+
+ switch (ops->mode) {
+ case MTD_OOB_PLACE:
+ buf += ops->ooboffs;
+ break;
+ default:
+ break;
+ }
+
+ calc_block_sector(from, &block0, &block1, &page, &ofs);
+ if (block1 > docg3->max_block)
+ return -EINVAL;
+
+ ret = doc_read_page_prepare(docg3, block0, block1, page,
+ ofs + DOC_LAYOUT_PAGE_SIZE);
+ if (!ret)
+ ret = doc_read_page_ecc_init(docg3, DOC_LAYOUT_OOB_SIZE);
+ if (!ret)
+ ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_OOB_SIZE,
+ buf, 1);
+ doc_read_page_finish(docg3);
+
+ if (ret > 0)
+ ops->oobretlen = ret;
+ else
+ ops->oobretlen = 0;
+ return (ret > 0) ? 0 : ret;
+}
+
+static int doc_reload_bbt(struct docg3 *docg3)
+{
+ int block = DOC_LAYOUT_BLOCK_BBT;
+ int ret = 0, nbpages, page;
+ u_char *buf = docg3->bbt;
+
+ nbpages = DIV_ROUND_UP(docg3->max_block + 1, 8 * DOC_LAYOUT_PAGE_SIZE);
+ for (page = 0; !ret && (page < nbpages); page++) {
+ ret = doc_read_page_prepare(docg3, block, block + 1,
+ page + DOC_LAYOUT_PAGE_BBT, 0);
+ if (!ret)
+ ret = doc_read_page_ecc_init(docg3,
+ DOC_LAYOUT_PAGE_SIZE);
+ if (!ret)
+ doc_read_page_getbytes(docg3, DOC_LAYOUT_PAGE_SIZE,
+ buf, 1);
+ buf += DOC_LAYOUT_PAGE_SIZE;
+ }
+ doc_read_page_finish(docg3);
+ return ret;
+}
+
+/**
+ * doc_block_isbad - Checks whether a block is good or not
+ * @mtd: the device
+ * @from: the offset to find the correct block
+ *
+ * Returns 1 if block is bad, 0 if block is good
+ */
+static int doc_block_isbad(struct mtd_info *mtd, loff_t from)
+{
+ struct docg3 *docg3 = mtd->priv;
+ int block0, block1, page, ofs, is_good;
+
+ calc_block_sector(from, &block0, &block1, &page, &ofs);
+ doc_dbg("doc_block_isbad(from=%lld) => block=(%d,%d), page=%d, ofs=%d\n",
+ from, block0, block1, page, ofs);
+
+ if (block0 < DOC_LAYOUT_BLOCK_FIRST_DATA)
+ return 0;
+ if (block1 > docg3->max_block)
+ return -EINVAL;
+
+ is_good = docg3->bbt[block0 >> 3] & (1 << (block0 & 0x7));
+ return !is_good;
+}
+
+/**
+ * doc_get_erase_count - Get block erase count
+ * @docg3: the device
+ * @from: the offset in which the block is.
+ *
+ * Get the number of times a block was erased. The number is the maximum of
+ * erase times between first and second plane (which should be equal normally).
+ *
+ * Returns The number of erases, or -EINVAL or -EIO on error.
+ */
+int doc_get_erase_count(struct docg3 *docg3, loff_t from)
+{
+ u8 buf[DOC_LAYOUT_WEAR_SIZE];
+ int ret, plane1_erase_count, plane2_erase_count;
+ int block0, block1, page, ofs;
+
+ doc_dbg("doc_get_erase_count(from=%lld, buf=%p)\n", from, buf);
+ if (from % DOC_LAYOUT_PAGE_SIZE)
+ return -EINVAL;
+ calc_block_sector(from, &block0, &block1, &page, &ofs);
+ if (block1 > docg3->max_block)
+ return -EINVAL;
+
+ ret = doc_reset_seq(docg3);
+ if (!ret)
+ ret = doc_read_page_prepare(docg3, block0, block1, page,
+ ofs + DOC_LAYOUT_WEAR_OFFSET);
+ if (!ret)
+ ret = doc_read_page_getbytes(docg3, DOC_LAYOUT_WEAR_SIZE,
+ buf, 1);
+ doc_read_page_finish(docg3);
+
+ if (ret || (buf[0] != DOC_ERASE_MARK) || (buf[2] != DOC_ERASE_MARK))
+ return -EIO;
+ plane1_erase_count = (u8)(~buf[1]) | ((u8)(~buf[4]) << 8)
+ | ((u8)(~buf[5]) << 16);
+ plane2_erase_count = (u8)(~buf[3]) | ((u8)(~buf[6]) << 8)
+ | ((u8)(~buf[7]) << 16);
+
+ return max(plane1_erase_count, plane2_erase_count);
+}
+
+/*
+ * Debug sysfs entries
+ */
+static ssize_t dbg_flashctrl_show(struct seq_file *s, void *p)
+{
+ struct docg3 *docg3 = (struct docg3 *)s->private;
+
+ int pos = 0;
+ u8 fctrl = doc_register_readb(docg3, DoC_FlashControl);
+
+ pos += seq_printf(s,
+ "FlashControl : 0x%02x (%s,CE# %s,%s,%s,flash %s)\n",
+ fctrl,
+ fctrl & Doc_Ctrl_Violation ? "protocol violation" : "-",
+ fctrl & Doc_Ctrl_CE ? "active" : "inactive",
+ fctrl & Doc_Ctrl_PROTECTION_ERROR ? "protection error" : "-",
+ fctrl & Doc_Ctrl_SEQUENCE_ERROR ? "sequence error" : "-",
+ fctrl & Doc_Ctrl_FLASHREADY ? "ready" : "not ready");
+ return pos;
+}
+DEBUGFS_RO_ATTR(flashcontrol, dbg_flashctrl_show);
+
+static ssize_t dbg_asicmode_show(struct seq_file *s, void *p)
+{
+ struct docg3 *docg3 = (struct docg3 *)s->private;
+
+ int pos = 0;
+ int pctrl = doc_register_readb(docg3, DoC_AsicMode);
+ int mode = pctrl & 0x03;
+
+ pos += seq_printf(s,
+ "%04x : RAM_WE=%d,RSTIN_RESET=%d,BDETCT_RESET=%d,WRITE_ENABLE=%d,POWERDOWN=%d,MODE=%d%d (",
+ pctrl,
+ pctrl & Doc_AsicMode_RAM_WE ? 1 : 0,
+ pctrl & Doc_AsicMode_RSTIN_RESET ? 1 : 0,
+ pctrl & Doc_AsicMode_BDETCT_RESET ? 1 : 0,
+ pctrl & Doc_AsicMode_MDWREN ? 1 : 0,
+ pctrl & Doc_AsicMode_POWERDOWN ? 1 : 0,
+ mode >> 1, mode & 0x1);
+
+ switch (mode) {
+ case Doc_AsicMode_RESET:
+ pos += seq_printf(s, "reset");
+ break;
+ case Doc_AsicMode_NORMAL:
+ pos += seq_printf(s, "normal");
+ break;
+ case Doc_AsicMode_POWERDOWN:
+ pos += seq_printf(s, "powerdown");
+ break;
+ }
+ pos += seq_printf(s, ")\n");
+ return pos;
+}
+DEBUGFS_RO_ATTR(asic_mode, dbg_asicmode_show);
+
+static ssize_t dbg_device_id_show(struct seq_file *s, void *p)
+{
+ struct docg3 *docg3 = (struct docg3 *)s->private;
+ int pos = 0;
+ int id = doc_register_readb(docg3, DoC_DeviceSelect);
+
+ pos += seq_printf(s, "DeviceId = %d\n", id);
+ return pos;
+}
+DEBUGFS_RO_ATTR(device_id, dbg_device_id_show);
+
+static ssize_t dbg_protection_show(struct seq_file *s, void *p)
+{
+ struct docg3 *docg3 = (struct docg3 *)s->private;
+ int pos = 0;
+ int protect = doc_register_readb(docg3, DoC_Protection);
+ int dps0 = doc_register_readb(docg3, DoC_DPS0_Status);
+ int dps0_low = doc_register_readb(docg3, DoC_DPS0_AddrLow);
+ int dps0_high = doc_register_readb(docg3, DoC_DPS0_AddrHigh);
+ int dps1 = doc_register_readb(docg3, DoC_DPS1_Status);
+ int dps1_low = doc_register_readb(docg3, DoC_DPS1_AddrLow);
+ int dps1_high = doc_register_readb(docg3, DoC_DPS1_AddrHigh);
+
+ pos += seq_printf(s, "Protection = 0x%02x (",
+ protect);
+ if (protect & Doc_Protect_FOUNDRY_OTP_LOCK)
+ pos += seq_printf(s, "FOUNDRY_OTP_LOCK,");
+ if (protect & Doc_Protect_CUSTOMER_OTP_LOCK)
+ pos += seq_printf(s, "CUSTOMER_OTP_LOCK,");
+ if (protect & Doc_Protect_LOCK_INPUT)
+ pos += seq_printf(s, "LOCK_INPUT,");
+ if (protect & Doc_Protect_STICKY_LOCK)
+ pos += seq_printf(s, "STICKY_LOCK,");
+ if (protect & Doc_Protect_PROTECTION_ENABLED)
+ pos += seq_printf(s, "PROTECTION ON,");
+ if (protect & Doc_Protect_IPL_DOWNLOAD_LOCK)
+ pos += seq_printf(s, "IPL_DOWNLOAD_LOCK,");
+ if (protect & Doc_Protect_PROTECTION_ERROR)
+ pos += seq_printf(s, "PROTECT_ERR,");
+ else
+ pos += seq_printf(s, "NO_PROTECT_ERR");
+ pos += seq_printf(s, ")\n");
+
+ pos += seq_printf(s, "DPS0 = 0x%02x : "
+ "Protected area [0x%x - 0x%x] : OTP=%d, READ=%d, "
+ "WRITE=%d, HW_LOCK=%d, KEY_OK=%d\n",
+ dps0, dps0_low, dps0_high,
+ !!(dps0 & Doc_DPS_OTP_PROTECTED),
+ !!(dps0 & Doc_DPS_READ_PROTECTED),
+ !!(dps0 & Doc_DPS_WRITE_PROTECTED),
+ !!(dps0 & Doc_DPS_HW_LOCK_ENABLED),
+ !!(dps0 & Doc_DPS_KEY_OK));
+ pos += seq_printf(s, "DPS1 = 0x%02x : "
+ "Protected area [0x%x - 0x%x] : OTP=%d, READ=%d, "
+ "WRITE=%d, HW_LOCK=%d, KEY_OK=%d\n",
+ dps1, dps1_low, dps1_high,
+ !!(dps1 & Doc_DPS_OTP_PROTECTED),
+ !!(dps1 & Doc_DPS_READ_PROTECTED),
+ !!(dps1 & Doc_DPS_WRITE_PROTECTED),
+ !!(dps1 & Doc_DPS_HW_LOCK_ENABLED),
+ !!(dps1 & Doc_DPS_KEY_OK));
+ return pos;
+}
+DEBUGFS_RO_ATTR(protection, dbg_protection_show);
+
+static int __init doc_dbg_register(struct docg3 *docg3)
+{
+ struct dentry *root, *entry;
+
+ root = debugfs_create_dir("docg3", NULL);
+ if (!root)
+ return -ENOMEM;
+
+ entry = debugfs_create_file("flashcontrol", S_IRUSR, root, docg3,
+ &flashcontrol_fops);
+ if (entry)
+ entry = debugfs_create_file("asic_mode", S_IRUSR, root,
+ docg3, &asic_mode_fops);
+ if (entry)
+ entry = debugfs_create_file("device_id", S_IRUSR, root,
+ docg3, &device_id_fops);
+ if (entry)
+ entry = debugfs_create_file("protection", S_IRUSR, root,
+ docg3, &protection_fops);
+ if (entry) {
+ docg3->debugfs_root = root;
+ return 0;
+ } else {
+ debugfs_remove_recursive(root);
+ return -ENOMEM;
+ }
+}
+
+static void __exit doc_dbg_unregister(struct docg3 *docg3)
+{
+ debugfs_remove_recursive(docg3->debugfs_root);
+}
+
+/**
+ * doc_set_driver_info - Fill the mtd_info structure and docg3 structure
+ * @chip_id: The chip ID of the supported chip
+ * @mtd: The structure to fill
+ */
+static void __init doc_set_driver_info(int chip_id, struct mtd_info *mtd)
+{
+ struct docg3 *docg3 = mtd->priv;
+ int cfg;
+
+ cfg = doc_register_readb(docg3, DoC_Configuration);
+ docg3->if_cfg = (cfg & Doc_Conf_IF_CFG ? 1 : 0);
+
+ switch (chip_id) {
+ case DOC_CHIPID_G3:
+ mtd->name = "DiskOnChip G3";
+ docg3->max_block = 2047;
+ break;
+ }
+ mtd->type = MTD_NANDFLASH;
+ /*
+ * Once write methods are added, the correct flags will be set.
+ * mtd->flags = MTD_CAP_NANDFLASH;
+ */
+ mtd->flags = MTD_CAP_ROM;
+ mtd->size = (docg3->max_block + 1) * DOC_LAYOUT_BLOCK_SIZE;
+ mtd->erasesize = DOC_LAYOUT_BLOCK_SIZE * DOC_LAYOUT_NBPLANES;
+ mtd->writesize = DOC_LAYOUT_PAGE_SIZE;
+ mtd->oobsize = DOC_LAYOUT_OOB_SIZE;
+ mtd->owner = THIS_MODULE;
+ mtd->erase = NULL;
+ mtd->point = NULL;
+ mtd->unpoint = NULL;
+ mtd->read = doc_read;
+ mtd->write = NULL;
+ mtd->read_oob = doc_read_oob;
+ mtd->write_oob = NULL;
+ mtd->sync = NULL;
+ mtd->block_isbad = doc_block_isbad;
+}
+
+/**
+ * doc_probe - Probe the IO space for a DiskOnChip G3 chip
+ * @pdev: platform device
+ *
+ * Probes for a G3 chip at the specified IO space in the platform data
+ * ressources.
+ *
+ * Returns 0 on success, -ENOMEM, -ENXIO on error
+ */
+static int __init docg3_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct docg3 *docg3;
+ struct mtd_info *mtd;
+ struct resource *ress;
+ struct mtd_partition *parts = NULL;
+ int ret, bbt_nbpages;
+ u16 chip_id, chip_id_inv;
+
+ ret = -ENOMEM;
+ docg3 = kzalloc(sizeof(struct docg3), GFP_KERNEL);
+ if (!docg3)
+ goto nomem1;
+ mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL);
+ if (!mtd)
+ goto nomem2;
+ mtd->priv = docg3;
+
+ ret = -ENXIO;
+ ress = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!ress) {
+ dev_err(dev, "No I/O memory resource defined\n");
+ goto noress;
+ }
+ docg3->base = ioremap(ress->start, DOC_IOSPACE_SIZE);
+
+ docg3->dev = &pdev->dev;
+ docg3->device_id = 0;
+ doc_set_device_id(docg3, docg3->device_id);
+ doc_set_asic_mode(docg3, Doc_AsicMode_RESET);
+ doc_set_asic_mode(docg3, Doc_AsicMode_NORMAL);
+
+ chip_id = doc_register_readw(docg3, DoC_ChipID);
+ chip_id_inv = doc_register_readw(docg3, DoC_ChipID_Inv);
+
+ ret = -ENODEV;
+ if (chip_id != (u16)(~chip_id_inv)) {
+ doc_info("No device found at IO addr %x\n", ress->start);
+ goto nochipfound;
+ }
+
+ switch (chip_id) {
+ case DOC_CHIPID_G3:
+ doc_info("Found a G3 DiskOnChip at addr %x\n", ress->start);
+ break;
+ default:
+ doc_err("Chip id %04x is not a DiskOnChip G3 chip\n", chip_id);
+ goto nochipfound;
+ }
+
+ doc_set_driver_info(chip_id, mtd);
+ platform_set_drvdata(pdev, mtd);
+
+ bbt_nbpages = (docg3->max_block + 1) / 8;
+ docg3->bbt = kzalloc(bbt_nbpages * DOC_LAYOUT_PAGE_SIZE, GFP_KERNEL);
+ if (!docg3->bbt)
+ goto nochipfound;
+ doc_reload_bbt(docg3);
+
+ ret = mtd_device_register(mtd, NULL, 0);
+ if (!ret)
+ ret = parse_mtd_partitions(mtd, part_probes, &parts, 0);
+ if (ret > 0)
+ ret = mtd_device_register(mtd, parts, ret);
+
+ doc_dbg_register(docg3);
+ return 0;
+
+nochipfound:
+ iounmap(docg3->base);
+noress:
+ kfree(mtd);
+nomem2:
+ kfree(docg3);
+nomem1:
+ return ret;
+}
+
+/**
+ * docg3_release - Release the driver
+ * @pdev: the platform device
+ *
+ * Returns 0
+ */
+static int __exit docg3_release(struct platform_device *pdev)
+{
+ struct mtd_info *mtd = platform_get_drvdata(pdev);
+ struct docg3 *docg3 = mtd->priv;
+
+ doc_dbg_unregister(docg3);
+ mtd_device_unregister(mtd);
+ iounmap(docg3->base);
+ kfree(docg3->bbt);
+ kfree(docg3);
+ kfree(mtd);
+ return 0;
+}
+
+static struct platform_driver g3_driver = {
+ .driver = {
+ .name = "docg3",
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(docg3_release),
+};
+
+static int __init docg3_init(void)
+{
+ return platform_driver_probe(&g3_driver, docg3_probe);
+}
+module_init(docg3_init);
+
+
+static void __exit docg3_exit(void)
+{
+ platform_driver_unregister(&g3_driver);
+}
+module_exit(docg3_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");
+MODULE_DESCRIPTION("MTD driver for DiskOnChip G3");
diff --git a/drivers/mtd/devices/docg3.h b/drivers/mtd/devices/docg3.h
new file mode 100644
index 0000000..c5dfedf
--- /dev/null
+++ b/drivers/mtd/devices/docg3.h
@@ -0,0 +1,237 @@
+#include <linux/mtd/nand_bch.h>
+
+/*
+ * Flash memory areas :
+ * - 0x0000 .. 0x07ff : IPL
+ * - 0x0800 .. 0x0fff : Data area
+ * - 0x1000 .. 0x17ff : Registers
+ * - 0x1800 .. 0x1fff : Unknown
+ */
+#define DOC_IOSPACE_IPL 0x0000
+#define DOC_IOSPACE_DATA 0x0800
+#define DOC_IOSPACE_SIZE 0x2000
+
+/*
+ * DOC G3 layout and adressing scheme
+ * A page address for the block "b", plane "P" and page "p":
+ * address = [bbbb bPpp pppp]
+ */
+
+#define DOC_ADDR_PAGE_MASK 0x3f
+#define DOC_ADDR_BLOCK_SHIFT 6
+#define DOC_LAYOUT_NBPLANES 2
+#define DOC_LAYOUT_PAGES_PER_BLOCK 64
+#define DOC_LAYOUT_PAGE_SIZE 512
+#define DOC_LAYOUT_OOB_SIZE 16
+#define DOC_LAYOUT_WEAR_SIZE 8
+#define DOC_LAYOUT_PAGE_OOB_SIZE \
+ (DOC_LAYOUT_PAGE_SIZE + DOC_LAYOUT_OOB_SIZE)
+#define DOC_LAYOUT_WEAR_OFFSET (DOC_LAYOUT_PAGE_OOB_SIZE * 2)
+#define DOC_LAYOUT_BLOCK_SIZE \
+ (DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_PAGE_SIZE)
+#define DOC_ECC_BCH_SIZE 7
+#define DOC_ECC_BCH_COVERED_BYTES \
+ (DOC_LAYOUT_PAGE_SIZE + DOC_LAYOUT_OOB_PAGEINFO_SZ + \
+ DOC_LAYOUT_OOB_HAMMING_SZ + DOC_LAYOUT_OOB_BCH_SZ)
+
+/*
+ * Blocks distribution
+ */
+#define DOC_LAYOUT_BLOCK_BBT 0
+#define DOC_LAYOUT_BLOCK_OTP 0
+#define DOC_LAYOUT_BLOCK_FIRST_DATA 6
+
+#define DOC_LAYOUT_PAGE_BBT 4
+
+/*
+ * Extra page OOB (16 bytes wide) layout
+ */
+#define DOC_LAYOUT_OOB_PAGEINFO_OFS 0
+#define DOC_LAYOUT_OOB_HAMMING_OFS 7
+#define DOC_LAYOUT_OOB_BCH_OFS 8
+#define DOC_LAYOUT_OOB_UNUSED_OFS 15
+#define DOC_LAYOUT_OOB_PAGEINFO_SZ 7
+#define DOC_LAYOUT_OOB_HAMMING_SZ 1
+#define DOC_LAYOUT_OOB_BCH_SZ 7
+#define DOC_LAYOUT_OOB_UNUSED_SZ 1
+
+
+#define DOC_CHIPID_G3 0x200
+#define DOC_ERASE_MARK 0xaa
+/*
+ * Flash registers
+ */
+#define DoC_ChipID 0x1000
+#define DoC_Test 0x1004
+#define DoC_BusLock 0x1006
+#define DoC_EndianControl 0x1008
+#define DoC_DeviceSelect 0x100a
+#define DoC_AsicMode 0x100c
+#define DoC_Configuration 0x100e
+#define DoC_InterruptControl 0x1010
+#define DoC_ReadAddress 0x101a
+#define DoC_DataEnd 0x101e
+#define DoC_InterruptStatus 0x1020
+
+#define DoC_FlashSequence 0x1032
+#define DoC_FlashCommand 0x1034
+#define DoC_FlashAddress 0x1036
+#define DoC_FlashControl 0x1038
+#define DoC_NOP 0x103e
+
+#define DoC_EccConf0 0x1040
+#define DoC_EccConf1 0x1042
+#define DoC_EccPreset 0x1044
+#define DoC_HammingParity 0x1046
+#define DoC_BCH_Syndrom(idx) (0x1048 + (idx << 1))
+
+#define DoC_Protection 0x1056
+#define DoC_DPS0_AddrLow 0x1060
+#define DoC_DPS0_AddrHigh 0x1062
+#define DoC_DPS1_AddrLow 0x1064
+#define DoC_DPS1_AddrHigh 0x1066
+#define DoC_DPS0_Status 0x106c
+#define DoC_DPS1_Status 0x106e
+
+#define DoC_AsicModeConfirm 0x1072
+#define DoC_ChipID_Inv 0x1074
+
+/*
+ * Flash sequences
+ * A sequence is preset before one or more commands are input to the chip.
+ */
+#define DoC_Seq_RESET 0x00
+#define DoC_Seq_PAGE_SIZE_532 0x03
+#define DoC_Seq_SET_MODE 0x09
+#define DoC_Seq_READ 0x12
+#define DoC_Seq_SET_PLANE1 0x0e
+#define DoC_Seq_SET_PLANE2 0x10
+#define DoC_Seq_PAGE_SETUP 0x1d
+
+/*
+ * Flash commands
+ */
+#define DoC_Cmd_READ_PLANE1 0x00
+#define DoC_Cmd_SET_ADDR_READ 0x05
+#define DoC_Cmd_READ_ALL_PLANES 0x30
+#define DoC_Cmd_READ_PLANE2 0x50
+#define DoC_Cmd_READ_FLASH 0xe0
+#define DoC_Cmd_PAGE_SIZE_532 0x3c
+
+#define DoC_Cmd_PROG_BLOCK_ADDR 0x60
+#define DoC_Cmd_PROG_CYCLE1 0x80
+#define DoC_Cmd_PROG_CYCLE2 0x10
+#define DoC_Cmd_ERASECYCLE2 0xd0
+
+#define DoC_Cmd_RELIABLE_MODE 0x22
+#define DoC_Cmd_FAST_MODE 0xa2
+
+#define DoC_Cmd_RESET 0xff
+
+/*
+ * Flash register : DoC_FlashControl
+ */
+#define Doc_Ctrl_Violation 0x20
+#define Doc_Ctrl_CE 0x10
+#define Doc_Ctrl_UNKNOWN_BITS 0x08
+#define Doc_Ctrl_PROTECTION_ERROR 0x04
+#define Doc_Ctrl_SEQUENCE_ERROR 0x02
+#define Doc_Ctrl_FLASHREADY 0x01
+
+/*
+ * Flash register : DoC_AsicMode
+ */
+#define Doc_AsicMode_RESET 0x00
+#define Doc_AsicMode_NORMAL 0x01
+#define Doc_AsicMode_POWERDOWN 0x02
+#define Doc_AsicMode_MDWREN 0x04
+#define Doc_AsicMode_BDETCT_RESET 0x08
+#define Doc_AsicMode_RSTIN_RESET 0x10
+#define Doc_AsicMode_RAM_WE 0x20
+
+/*
+ * Flash register : DoC_EccConf0
+ */
+#define Doc_ECCConf0_READ_MODE 0x8000
+#define Doc_ECCConf0_AUTO_ECC_ENABLE 0x4000
+#define Doc_ECCConf0_HAMMING_ENABLE 0x1000
+#define Doc_ECCConf0_BCH_ENABLE 0x0800
+#define Doc_ECCConf0_DATA_BYTES_MASK 0x07ff
+
+/*
+ * Flash register : DoC_EccConf1
+ */
+#define Doc_ECCConf1_BCH_SYNDROM_ERR 0x80
+#define Doc_ECCConf1_UNKOWN1 0x40
+#define Doc_ECCConf1_UNKOWN2 0x20
+#define Doc_ECCConf1_UNKOWN3 0x10
+#define Doc_ECCConf1_HAMMING_BITS_MASK 0x0f
+
+/*
+ * Flash register : DoC_Protection
+ */
+#define Doc_Protect_FOUNDRY_OTP_LOCK 0x01
+#define Doc_Protect_CUSTOMER_OTP_LOCK 0x02
+#define Doc_Protect_LOCK_INPUT 0x04
+#define Doc_Protect_STICKY_LOCK 0x08
+#define Doc_Protect_PROTECTION_ENABLED 0x10
+#define Doc_Protect_IPL_DOWNLOAD_LOCK 0x20
+#define Doc_Protect_PROTECTION_ERROR 0x80
+
+/*
+ * Flash register : DoC_DPS0_Status and DoC_DPS1_Status
+ */
+#define Doc_DPS_OTP_PROTECTED 0x01
+#define Doc_DPS_READ_PROTECTED 0x02
+#define Doc_DPS_WRITE_PROTECTED 0x04
+#define Doc_DPS_HW_LOCK_ENABLED 0x08
+#define Doc_DPS_KEY_OK 0x80
+
+/*
+ * Flash register : DoC_Configuration
+ */
+#define Doc_Conf_IF_CFG 0x80
+#define Doc_Conf_MAX_ID_MASK 0x30
+#define Doc_Conf_VCCQ_3V 0x01
+
+/*
+ * Flash register : DoC_ReadAddress
+ */
+#define Doc_ReadAddr_INC 0x8000
+#define Doc_ReadAddr_ONE_BYTE 0x4000
+#define Doc_ReadAddr_ADDR_MASK 0x1fff
+
+/**
+ * struct docg3 - DiskOnChip driver private data
+ * @dev: the device currently under control
+ * @base: mapped IO space
+ * @device_id: number of the cascaded DoCG3 device (0, 1, 2 or 3)
+ * @if_cfg: if true, reads are on 16bits, else reads are on 8bits
+ * @bbt: bad block table cache
+ * @debugfs_root: debugfs root node
+ */
+struct docg3 {
+ struct device *dev;
+ void __iomem *base;
+ int device_id:4;
+ int if_cfg:1;
+ int max_block;
+ u8 *bbt;
+ struct dentry *debugfs_root;
+};
+
+#define doc_err(fmt, arg...) dev_err(docg3->dev, (fmt), ## arg)
+#define doc_info(fmt, arg...) dev_info(docg3->dev, (fmt), ## arg)
+#define doc_dbg(fmt, arg...) dev_dbg(docg3->dev, (fmt), ## arg)
+#define doc_vdbg(fmt, arg...) dev_vdbg(docg3->dev, (fmt), ## arg)
+
+#define DEBUGFS_RO_ATTR(name, show_fct) \
+ static int name##_open(struct inode *inode, struct file *file) \
+ { return single_open(file, show_fct, inode->i_private); } \
+ static const struct file_operations name##_fops = { \
+ .owner = THIS_MODULE, \
+ .open = name##_open, \
+ .llseek = seq_lseek, \
+ .read = seq_read, \
+ .release = single_release \
+ };
--
1.7.4.1


\
 
 \ /
  Last update: 2011-09-21 21:31    [W:0.092 / U:14.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site