lkml.org 
[lkml]   [2011]   [Aug]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V3 14/20] dmaengine/amba-pl08x: Add prep_single_byte_llis() routine
Date
Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.

Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
---
drivers/dma/amba-pl08x.c | 61 +++++++++++++++++++++++++---------------------
1 files changed, 33 insertions(+), 28 deletions(-)

diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index e5930d5..45d8a5d 100644
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -559,6 +559,14 @@ static void pl08x_fill_lli_for_desc(struct pl08x_lli_build_data *bd,
bd->remainder -= len;
}

+static inline void prep_byte_width_lli(struct pl08x_lli_build_data *bd,
+ u32 *cctl, u32 len, int num_llis, size_t *total_bytes)
+{
+ *cctl = pl08x_cctl_bits(*cctl, 1, 1, len);
+ pl08x_fill_lli_for_desc(bd, num_llis, len, *cctl);
+ (*total_bytes) += len;
+}
+
/*
* This fills in the table of LLIs for the transfer descriptor
* Note that we assume we never have to change the burst sizes
@@ -570,7 +578,7 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
struct pl08x_bus_data *mbus, *sbus;
struct pl08x_lli_build_data bd;
int num_llis = 0;
- u32 cctl;
+ u32 cctl, early_bytes = 0;
size_t max_bytes_per_lli, total_bytes = 0;
struct pl08x_lli *llis_va;

@@ -619,29 +627,27 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
mbus == &bd.srcbus ? "src" : "dst",
sbus == &bd.srcbus ? "src" : "dst");

- if (txd->len < mbus->buswidth) {
- /* Less than a bus width available - send as single bytes */
- while (bd.remainder) {
- dev_vdbg(&pl08x->adev->dev,
- "%s single byte LLIs for a transfer of "
- "less than a bus width (remain 0x%08x)\n",
- __func__, bd.remainder);
- cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
- pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
- total_bytes++;
- }
- } else {
- /* Make one byte LLIs until master bus is aligned */
- while ((mbus->addr) % (mbus->buswidth)) {
- dev_vdbg(&pl08x->adev->dev,
- "%s adjustment lli for less than bus width "
- "(remain 0x%08x)\n",
- __func__, bd.remainder);
- cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
- pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
- total_bytes++;
- }
+ /*
+ * Send byte by byte for following cases
+ * - Less than a bus width available
+ * - until master bus is aligned
+ */
+ if (bd.remainder < mbus->buswidth)
+ early_bytes = bd.remainder;
+ else if ((mbus->addr) % (mbus->buswidth)) {
+ early_bytes = mbus->buswidth - (mbus->addr) % (mbus->buswidth);
+ if ((bd.remainder - early_bytes) < mbus->buswidth)
+ early_bytes = bd.remainder;
+ }
+
+ if (early_bytes) {
+ dev_vdbg(&pl08x->adev->dev, "%s byte width LLIs "
+ "(remain 0x%08x)\n", __func__, bd.remainder);
+ prep_byte_width_lli(&bd, &cctl, early_bytes, num_llis++,
+ &total_bytes);
+ }

+ if (bd.remainder) {
/*
* Master now aligned
* - if slave is not then we must set its width down
@@ -692,13 +698,12 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
/*
* Send any odd bytes
*/
- while (bd.remainder) {
- cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
+ if (bd.remainder) {
dev_vdbg(&pl08x->adev->dev,
- "%s align with boundary, single odd byte (remain %zu)\n",
+ "%s align with boundary, send odd bytes (remain %zu)\n",
__func__, bd.remainder);
- pl08x_fill_lli_for_desc(&bd, num_llis++, 1, cctl);
- total_bytes++;
+ prep_byte_width_lli(&bd, &cctl, bd.remainder,
+ num_llis++, &total_bytes);
}
}

--
1.7.2.2


\
 
 \ /
  Last update: 2011-08-05 12:07    [W:0.143 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site