lkml.org 
[lkml]   [2011]   [May]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    Subject[08/24] ehea: fix wrongly reported speed and port
    2.6.33-longterm review patch.  If anyone has any objections, please let us know.

    ------------------
    Content-Length: 1935
    Lines: 51

    From: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>

    commit dcbe14b91a920657ff3a9ba0efb7c5b5562f956a upstream.

    Currently EHEA reports to ethtool as supporting 10M, 100M, 1G and
    10G and connected to FIBRE independent of the hardware configuration.
    However, when connected to FIBRE the only supported speed is 10G
    full-duplex, and the other speeds and modes are only supported
    when connected to twisted pair.

    Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
    Acked-by: Breno Leitao <leitao@linux.vnet.ibm.com>
    Signed-off-by: David S. Miller <davem@davemloft.net>
    Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

    ---
    drivers/net/ehea/ehea_ethtool.c | 21 +++++++++++++--------
    1 file changed, 13 insertions(+), 8 deletions(-)

    --- a/drivers/net/ehea/ehea_ethtool.c
    +++ b/drivers/net/ehea/ehea_ethtool.c
    @@ -53,15 +53,20 @@ static int ehea_get_settings(struct net_
    cmd->duplex = -1;
    }

    - cmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_1000baseT_Full
    - | SUPPORTED_100baseT_Full | SUPPORTED_100baseT_Half
    - | SUPPORTED_10baseT_Full | SUPPORTED_10baseT_Half
    - | SUPPORTED_Autoneg | SUPPORTED_FIBRE);
    -
    - cmd->advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_Autoneg
    - | ADVERTISED_FIBRE);
    + if (cmd->speed == SPEED_10000) {
    + cmd->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
    + cmd->advertising = (ADVERTISED_10000baseT_Full | ADVERTISED_FIBRE);
    + cmd->port = PORT_FIBRE;
    + } else {
    + cmd->supported = (SUPPORTED_1000baseT_Full | SUPPORTED_100baseT_Full
    + | SUPPORTED_100baseT_Half | SUPPORTED_10baseT_Full
    + | SUPPORTED_10baseT_Half | SUPPORTED_Autoneg
    + | SUPPORTED_TP);
    + cmd->advertising = (ADVERTISED_1000baseT_Full | ADVERTISED_Autoneg
    + | ADVERTISED_TP);
    + cmd->port = PORT_TP;
    + }

    - cmd->port = PORT_FIBRE;
    cmd->autoneg = port->autoneg == 1 ? AUTONEG_ENABLE : AUTONEG_DISABLE;

    return 0;



    \
     
     \ /
      Last update: 2011-05-19 20:39    [W:0.027 / U:0.064 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site