lkml.org 
[lkml]   [2011]   [Mar]   [31]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: Commit 7eaceaccab5f40 causing boot hang.
From
Date
On Thu, 2011-03-31 at 13:09 +0200, Jens Axboe wrote:
> On 2011-03-31 12:47, Rob Landley wrote:
> > On 03/31/2011 05:37 AM, Jens Axboe wrote:
> >> On 2011-03-31 12:07, Jens Axboe wrote:
> >>> On 2011-03-31 11:11, Rob Landley wrote:
> >>>> On 03/31/2011 04:02 AM, Jens Axboe wrote:
> >>>>> On 2011-03-30 15:52, Rob Landley wrote:
> >>>>>> On 03/30/2011 06:38 AM, Jens Axboe wrote:
> >>>>>>> On 2011-03-30 08:06, Rob Landley wrote:
> >>>>>>>> On 03/29/2011 10:51 AM, Pete Clements wrote:
> >>>>>>>>> Quoting Jens Axboe

<SNIP>

> >>>>>>>>> I have had a similiar problem (reported earlier) unable to boot.
> >>>>>>>>> With git15-18 hung with IDE drives (hda), git19-21 moved the hang down to
> >>>>>>>>> the IDE CDROM (hdc). Applied the above patch and now booted into git21 without
> >>>>>>>>> any hang and all appears ok.
> >>>>>>>>
> >>>>>>>> It may have made it better for me, it's hard to tell.
> >>>>>>>>
> >>>>>>>> I did a fresh pull, re-applied the patch, and tried again with
> >>>>>>>> init=/bin/sh and it booted to the shell prompt... which then hung when I
> >>>>>>>> did "ls -l /".
> >>>>>>>>
> >>>>>>>> If I let it boot normally, init announces itself, gives a spurious
> >>>>>>>> warning about a fstab field (which it's been doing for a while, my fault
> >>>>>>>> but harmless), then hangs.
> >>>>>>>>
> >>>>>>>>> This is i386, UP.
> >>>>>>>>
> >>>>>>>> I'm doing x86-64 SMP.
> >>>>>>>
> >>>>>>> I think we have the same issue the other location. How about this, then:
> >>>>>>>
> >>>>>>> diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
> >>>>>>> index 0e406d73..4978ec3 100644
> >>>>>>> --- a/drivers/ide/ide-io.c
> >>>>>>> +++ b/drivers/ide/ide-io.c
> >>>>>>> @@ -549,12 +549,11 @@ plug_device:
> >>>>>>> spin_unlock_irq(&hwif->lock);
> >>>>>>> ide_unlock_host(host);
> >>>>>>> plug_device_2:
> >>>>>>> + blk_delay_queue(q, queue_run_ms);
> >>>>>>> spin_lock_irq(q->queue_lock);
> >>>>>>>
> >>>>>>> - if (rq) {
> >>>>>>> + if (rq)
> >>>>>>> blk_requeue_request(q, rq);
> >>>>>>> - blk_delay_queue(q, queue_run_ms);
> >>>>>>> - }
> >>>>>>> }
> >>>>>>>
> >>>>>>> void ide_requeue_and_plug(ide_drive_t *drive, struct request *rq)
> >>>>>>> @@ -570,8 +569,7 @@ void ide_requeue_and_plug(ide_drive_t *drive, struct request *rq)
> >>>>>>> spin_unlock_irqrestore(q->queue_lock, flags);
> >>>>>>>
> >>>>>>> /* Use 3ms as that was the old plug delay */
> >>>>>>> - if (rq)
> >>>>>>> - blk_delay_queue(q, 3);
> >>>>>>> + blk_delay_queue(q, 3);
> >>>>>>> }
> >>>>>>>
> >>>>>>> static int drive_is_ready(ide_drive_t *drive)
> >>>>>>>
> >>>>>>
> >>>>>> Did a fresh pull and applied that patch. (It conflicts with your
> >>>>>> previous one, but looks like it includes it.)
> >>>>>>
> >>>>>> Now it hangs after the "EXT3-fs: barriers not enabled" line, doesn't
> >>>>>> make it to init.
> >>>>>
> >>>>> I have tried hard to reproduce this, but even stock 2.6.39-rc1 works
> >>>>> fine for me here. Setup a KVM image with a debian 6 install, then
> >>>>> converted it to IDE and booting it with a custom kernel like you are.
> >>>>> Works fine, boots and I can do disk activity tests and it all works.
> >>>>>
> >>>>> Can you send me your .config?
> >>>>
> >>>> It was attached to the first message in this series, here it is again.
> >>>>
> >>>> I update it via "make oldconfig" and hold down return.
> >>>>
> >>>> I boot it via:
> >>>>
> >>>> qemu-system-x86_64 -m 1024 -kernel arch/x86/boot/bzImage \
> >>>> -hda ~/sid.ext3 -append "root=/dev/hda rw"
> >>>
> >>> Much better, I see the hang now! Now to try and diagnose...
> >>
> >> It seems to hard hang, looks very odd:
> >
> > I should have mentioned that: when it hangs, you can't page back up in
> > the console display anymore.
>
> Data point - only seems to happen on UP. If you add -smp X to kvm, then
> it boots and works just fine. It smells oddly like some sort of irq
> event.
>

Hi Jens and Co,

I ran into this same problem yesterday with .39-rc1 in my HW target mode
QEMU/KVM development environment. I applied the above patch, which
still hangs during boot with the following usage QEMU-KVM usage:

qemu-system-x86_64 -m 2048 -smp 4 -device pci-assign,host=02:00.0
-device pci-assign,host=06:00.0 /root/lenny64guest0-orig.img -serial
file:serial-36.log

However, after adding the '-cdrom ~/linux-distro.iso' parameter to the
above w/ your patch I am now about to boot without issue into .39-rc1
guest and everything appears fine for root=/dev/hda1.

So AFAICT it seems to be related to ide_cd_mod.ko with an empty drive..

--nab



\
 
 \ /
  Last update: 2011-04-01 05:21    [W:0.226 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site