lkml.org 
[lkml]   [2011]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 16/19] eukrea-cpuimx51: remove board
Date
this board is not maintained anymore and is replaced by cpuimx51sd

Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
---
arch/arm/configs/mx5_defconfig | 1 -
arch/arm/mach-mx5/Kconfig | 30 ---
arch/arm/mach-mx5/Makefile | 2 -
arch/arm/mach-mx5/board-cpuimx51.c | 300 --------------------------
arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c | 206 ------------------
5 files changed, 0 insertions(+), 539 deletions(-)
delete mode 100644 arch/arm/mach-mx5/board-cpuimx51.c
delete mode 100644 arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c

diff --git a/arch/arm/configs/mx5_defconfig b/arch/arm/configs/mx5_defconfig
index d0d8dfe..32e91f8 100644
--- a/arch/arm/configs/mx5_defconfig
+++ b/arch/arm/configs/mx5_defconfig
@@ -17,7 +17,6 @@ CONFIG_ARCH_MXC=y
CONFIG_ARCH_MX5=y
CONFIG_MACH_MX51_BABBAGE=y
CONFIG_MACH_MX51_3DS=y
-CONFIG_MACH_EUKREA_CPUIMX51=y
CONFIG_MACH_EUKREA_CPUIMX51SD=y
CONFIG_MACH_MX51_EFIKAMX=y
CONFIG_MACH_MX51_EFIKASB=y
diff --git a/arch/arm/mach-mx5/Kconfig b/arch/arm/mach-mx5/Kconfig
index af0c212..0cea604 100644
--- a/arch/arm/mach-mx5/Kconfig
+++ b/arch/arm/mach-mx5/Kconfig
@@ -93,36 +93,6 @@ config MACH_MX51_3DS
Include support for MX51PDK (3DS) platform. This includes specific
configurations for the board and its peripherals.

-config MACH_EUKREA_CPUIMX51
- bool "Support Eukrea CPUIMX51 module"
- select SOC_IMX51
- select IMX_HAVE_PLATFORM_FSL_USB2_UDC
- select IMX_HAVE_PLATFORM_IMX_I2C
- select IMX_HAVE_PLATFORM_IMX_UART
- select IMX_HAVE_PLATFORM_MXC_EHCI
- select IMX_HAVE_PLATFORM_MXC_NAND
- select IMX_HAVE_PLATFORM_SPI_IMX
- help
- Include support for Eukrea CPUIMX51 platform. This includes
- specific configurations for the module and its peripherals.
-
-choice
- prompt "Baseboard"
- depends on MACH_EUKREA_CPUIMX51
- default MACH_EUKREA_MBIMX51_BASEBOARD
-
-config MACH_EUKREA_MBIMX51_BASEBOARD
- prompt "Eukrea MBIMX51 development board"
- bool
- select IMX_HAVE_PLATFORM_IMX_KEYPAD
- select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
- select LEDS_GPIO_REGISTER
- help
- This adds board specific devices that can be found on Eukrea's
- MBIMX51 evaluation board.
-
-endchoice
-
config MACH_EUKREA_CPUIMX51SD
bool "Support Eukrea CPUIMX51SD module"
select SOC_IMX51
diff --git a/arch/arm/mach-mx5/Makefile b/arch/arm/mach-mx5/Makefile
index 0fc6080..596c1c7 100644
--- a/arch/arm/mach-mx5/Makefile
+++ b/arch/arm/mach-mx5/Makefile
@@ -13,8 +13,6 @@ obj-$(CONFIG_MACH_MX53_EVK) += board-mx53_evk.o
obj-$(CONFIG_MACH_MX53_SMD) += board-mx53_smd.o
obj-$(CONFIG_MACH_MX53_LOCO) += board-mx53_loco.o
obj-$(CONFIG_MACH_MX53_ARD) += board-mx53_ard.o
-obj-$(CONFIG_MACH_EUKREA_CPUIMX51) += board-cpuimx51.o
-obj-$(CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD) += eukrea_mbimx51-baseboard.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += board-cpuimx51sd.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd-baseboard.o
obj-$(CONFIG_MX51_EFIKA_COMMON) += mx51_efika.o
diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c
deleted file mode 100644
index 1fc1103..0000000
--- a/arch/arm/mach-mx5/board-cpuimx51.c
+++ /dev/null
@@ -1,300 +0,0 @@
-/*
- *
- * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
- *
- * based on board-mx51_babbage.c which is
- * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/interrupt.h>
-
-#include <mach/eukrea-baseboards.h>
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "devices-imx51.h"
-
-#define CPUIMX51_USBH1_STP IMX_GPIO_NR(1, 27)
-#define CPUIMX51_QUARTA_GPIO IMX_GPIO_NR(3, 28)
-#define CPUIMX51_QUARTB_GPIO IMX_GPIO_NR(3, 25)
-#define CPUIMX51_QUARTC_GPIO IMX_GPIO_NR(3, 26)
-#define CPUIMX51_QUARTD_GPIO IMX_GPIO_NR(3, 27)
-#define CPUIMX51_QUART_XTAL 14745600
-#define CPUIMX51_QUART_REGSHIFT 17
-
-/* USB_CTRL_1 */
-#define MX51_USB_CTRL_1_OFFSET 0x10
-#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
-
-#define MX51_USB_PLLDIV_12_MHZ 0x00
-#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
-#define MX51_USB_PLL_DIV_24_MHZ 0x02
-
-static struct plat_serial8250_port serial_platform_data[] = {
- {
- .mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x400000),
- .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTA_GPIO),
- .irqflags = IRQF_TRIGGER_HIGH,
- .uartclk = CPUIMX51_QUART_XTAL,
- .regshift = CPUIMX51_QUART_REGSHIFT,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
- }, {
- .mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x800000),
- .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTB_GPIO),
- .irqflags = IRQF_TRIGGER_HIGH,
- .uartclk = CPUIMX51_QUART_XTAL,
- .regshift = CPUIMX51_QUART_REGSHIFT,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
- }, {
- .mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x1000000),
- .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTC_GPIO),
- .irqflags = IRQF_TRIGGER_HIGH,
- .uartclk = CPUIMX51_QUART_XTAL,
- .regshift = CPUIMX51_QUART_REGSHIFT,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
- }, {
- .mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x2000000),
- .irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTD_GPIO),
- .irqflags = IRQF_TRIGGER_HIGH,
- .uartclk = CPUIMX51_QUART_XTAL,
- .regshift = CPUIMX51_QUART_REGSHIFT,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
- }, {
- }
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = 0,
- .dev = {
- .platform_data = serial_platform_data,
- },
-};
-
-static struct platform_device *devices[] __initdata = {
- &serial_device,
-};
-
-static iomux_v3_cfg_t eukrea_cpuimx51_pads[] = {
- /* UART1 */
- MX51_PAD_UART1_RXD__UART1_RXD,
- MX51_PAD_UART1_TXD__UART1_TXD,
- MX51_PAD_UART1_RTS__UART1_RTS,
- MX51_PAD_UART1_CTS__UART1_CTS,
-
- /* I2C2 */
- MX51_PAD_GPIO1_2__I2C2_SCL,
- MX51_PAD_GPIO1_3__I2C2_SDA,
- MX51_PAD_NANDF_D10__GPIO3_30,
-
- /* QUART IRQ */
- MX51_PAD_NANDF_D15__GPIO3_25,
- MX51_PAD_NANDF_D14__GPIO3_26,
- MX51_PAD_NANDF_D13__GPIO3_27,
- MX51_PAD_NANDF_D12__GPIO3_28,
-
- /* USB HOST1 */
- MX51_PAD_USBH1_CLK__USBH1_CLK,
- MX51_PAD_USBH1_DIR__USBH1_DIR,
- MX51_PAD_USBH1_NXT__USBH1_NXT,
- MX51_PAD_USBH1_DATA0__USBH1_DATA0,
- MX51_PAD_USBH1_DATA1__USBH1_DATA1,
- MX51_PAD_USBH1_DATA2__USBH1_DATA2,
- MX51_PAD_USBH1_DATA3__USBH1_DATA3,
- MX51_PAD_USBH1_DATA4__USBH1_DATA4,
- MX51_PAD_USBH1_DATA5__USBH1_DATA5,
- MX51_PAD_USBH1_DATA6__USBH1_DATA6,
- MX51_PAD_USBH1_DATA7__USBH1_DATA7,
- MX51_PAD_USBH1_STP__USBH1_STP,
-};
-
-static const struct mxc_nand_platform_data
- eukrea_cpuimx51_nand_board_info __initconst = {
- .width = 1,
- .hw_ecc = 1,
- .flash_bbt = 1,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const
-struct imxi2c_platform_data eukrea_cpuimx51_i2c_data __initconst = {
- .bitrate = 100000,
-};
-
-static struct i2c_board_info eukrea_cpuimx51_i2c_devices[] = {
- {
- I2C_BOARD_INFO("pcf8563", 0x51),
- },
-};
-
-/* This function is board specific as the bit mask for the plldiv will also
-be different for other Freescale SoCs, thus a common bitmask is not
-possible and cannot get place in /plat-mxc/ehci.c.*/
-static int initialize_otg_port(struct platform_device *pdev)
-{
- u32 v;
- void __iomem *usb_base;
- void __iomem *usbother_base;
-
- usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
- if (!usb_base)
- return -ENOMEM;
- usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
- /* Set the PHY clock to 19.2MHz */
- v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
- v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
- v |= MX51_USB_PLL_DIV_19_2_MHZ;
- __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
- iounmap(usb_base);
-
- mdelay(10);
-
- return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
-}
-
-static int initialize_usbh1_port(struct platform_device *pdev)
-{
- u32 v;
- void __iomem *usb_base;
- void __iomem *usbother_base;
-
- usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
- if (!usb_base)
- return -ENOMEM;
- usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
-
- /* The clock for the USBH1 ULPI port will come externally from the PHY. */
- v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
- __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
- iounmap(usb_base);
-
- mdelay(10);
-
- return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
- MXC_EHCI_ITC_NO_THRESHOLD);
-}
-
-static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
- .init = initialize_otg_port,
- .portsc = MXC_EHCI_UTMI_16BIT,
-};
-
-static const struct fsl_usb2_platform_data usb_pdata __initconst = {
- .operating_mode = FSL_USB2_DR_DEVICE,
- .phy_mode = FSL_USB2_PHY_UTMI_WIDE,
-};
-
-static const struct mxc_usbh_platform_data usbh1_config __initconst = {
- .init = initialize_usbh1_port,
- .portsc = MXC_EHCI_MODE_ULPI,
-};
-
-static int otg_mode_host;
-
-static int __init eukrea_cpuimx51_otg_mode(char *options)
-{
- if (!strcmp(options, "host"))
- otg_mode_host = 1;
- else if (!strcmp(options, "device"))
- otg_mode_host = 0;
- else
- pr_info("otg_mode neither \"host\" nor \"device\". "
- "Defaulting to device\n");
- return 0;
-}
-__setup("otg_mode=", eukrea_cpuimx51_otg_mode);
-
-/*
- * Board specific initialization.
- */
-static void __init eukrea_cpuimx51_init(void)
-{
- imx51_soc_init();
-
- mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51_pads,
- ARRAY_SIZE(eukrea_cpuimx51_pads));
-
- imx51_add_imx_uart(0, &uart_pdata);
- imx51_add_mxc_nand(&eukrea_cpuimx51_nand_board_info);
-
- gpio_request(CPUIMX51_QUARTA_GPIO, "quarta_irq");
- gpio_direction_input(CPUIMX51_QUARTA_GPIO);
- gpio_free(CPUIMX51_QUARTA_GPIO);
- gpio_request(CPUIMX51_QUARTB_GPIO, "quartb_irq");
- gpio_direction_input(CPUIMX51_QUARTB_GPIO);
- gpio_free(CPUIMX51_QUARTB_GPIO);
- gpio_request(CPUIMX51_QUARTC_GPIO, "quartc_irq");
- gpio_direction_input(CPUIMX51_QUARTC_GPIO);
- gpio_free(CPUIMX51_QUARTC_GPIO);
- gpio_request(CPUIMX51_QUARTD_GPIO, "quartd_irq");
- gpio_direction_input(CPUIMX51_QUARTD_GPIO);
- gpio_free(CPUIMX51_QUARTD_GPIO);
-
- imx51_add_fec(NULL);
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- imx51_add_imx_i2c(1, &eukrea_cpuimx51_i2c_data);
- i2c_register_board_info(1, eukrea_cpuimx51_i2c_devices,
- ARRAY_SIZE(eukrea_cpuimx51_i2c_devices));
-
- if (otg_mode_host)
- imx51_add_mxc_ehci_otg(&dr_utmi_config);
- else {
- initialize_otg_port(NULL);
- imx51_add_fsl_usb2_udc(&usb_pdata);
- }
- imx51_add_mxc_ehci_hs(1, &usbh1_config);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD
- eukrea_mbimx51_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx51_timer_init(void)
-{
- mx51_clocks_init(32768, 24000000, 22579200, 0);
-}
-
-static struct sys_timer mxc_timer = {
- .init = eukrea_cpuimx51_timer_init,
-};
-
-MACHINE_START(EUKREA_CPUIMX51, "Eukrea CPUIMX51 Module")
- /* Maintainer: Eric Bénard <eric@eukrea.com> */
- .atag_offset = 0x100,
- .map_io = mx51_map_io,
- .init_early = imx51_init_early,
- .init_irq = mx51_init_irq,
- .handle_irq = imx51_handle_irq,
- .timer = &mxc_timer,
- .init_machine = eukrea_cpuimx51_init,
-MACHINE_END
diff --git a/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c b/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c
deleted file mode 100644
index a6a3ab8..0000000
--- a/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c
+++ /dev/null
@@ -1,206 +0,0 @@
-/*
- *
- * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/io.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/i2c/tsc2007.h>
-#include <linux/leds.h>
-
-#include <mach/common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-mx51.h>
-
-#include <asm/mach/arch.h>
-
-#include "devices-imx51.h"
-
-#define MBIMX51_TSC2007_GPIO IMX_GPIO_NR(3, 30)
-#define MBIMX51_LED0 IMX_GPIO_NR(3, 5)
-#define MBIMX51_LED1 IMX_GPIO_NR(3, 6)
-#define MBIMX51_LED2 IMX_GPIO_NR(3, 7)
-#define MBIMX51_LED3 IMX_GPIO_NR(3, 8)
-
-static const struct gpio_led mbimx51_leds[] __initconst = {
- {
- .name = "led0",
- .default_trigger = "heartbeat",
- .active_low = 1,
- .gpio = MBIMX51_LED0,
- },
- {
- .name = "led1",
- .default_trigger = "nand-disk",
- .active_low = 1,
- .gpio = MBIMX51_LED1,
- },
- {
- .name = "led2",
- .default_trigger = "mmc0",
- .active_low = 1,
- .gpio = MBIMX51_LED2,
- },
- {
- .name = "led3",
- .default_trigger = "default-on",
- .active_low = 1,
- .gpio = MBIMX51_LED3,
- },
-};
-
-static const struct gpio_led_platform_data mbimx51_leds_info __initconst = {
- .leds = mbimx51_leds,
- .num_leds = ARRAY_SIZE(mbimx51_leds),
-};
-
-static iomux_v3_cfg_t mbimx51_pads[] = {
- /* UART2 */
- MX51_PAD_UART2_RXD__UART2_RXD,
- MX51_PAD_UART2_TXD__UART2_TXD,
-
- /* UART3 */
- MX51_PAD_UART3_RXD__UART3_RXD,
- MX51_PAD_UART3_TXD__UART3_TXD,
- MX51_PAD_KEY_COL4__UART3_RTS,
- MX51_PAD_KEY_COL5__UART3_CTS,
-
- /* TSC2007 IRQ */
- MX51_PAD_NANDF_D10__GPIO3_30,
-
- /* LEDS */
- MX51_PAD_DISPB2_SER_DIN__GPIO3_5,
- MX51_PAD_DISPB2_SER_DIO__GPIO3_6,
- MX51_PAD_DISPB2_SER_CLK__GPIO3_7,
- MX51_PAD_DISPB2_SER_RS__GPIO3_8,
-
- /* KPP */
- MX51_PAD_KEY_ROW0__KEY_ROW0,
- MX51_PAD_KEY_ROW1__KEY_ROW1,
- MX51_PAD_KEY_ROW2__KEY_ROW2,
- MX51_PAD_KEY_ROW3__KEY_ROW3,
- MX51_PAD_KEY_COL0__KEY_COL0,
- MX51_PAD_KEY_COL1__KEY_COL1,
- MX51_PAD_KEY_COL2__KEY_COL2,
- MX51_PAD_KEY_COL3__KEY_COL3,
-
- /* SD 1 */
- MX51_PAD_SD1_CMD__SD1_CMD,
- MX51_PAD_SD1_CLK__SD1_CLK,
- MX51_PAD_SD1_DATA0__SD1_DATA0,
- MX51_PAD_SD1_DATA1__SD1_DATA1,
- MX51_PAD_SD1_DATA2__SD1_DATA2,
- MX51_PAD_SD1_DATA3__SD1_DATA3,
-
- /* SD 2 */
- MX51_PAD_SD2_CMD__SD2_CMD,
- MX51_PAD_SD2_CLK__SD2_CLK,
- MX51_PAD_SD2_DATA0__SD2_DATA0,
- MX51_PAD_SD2_DATA1__SD2_DATA1,
- MX51_PAD_SD2_DATA2__SD2_DATA2,
- MX51_PAD_SD2_DATA3__SD2_DATA3,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
- .flags = IMXUART_HAVE_RTSCTS,
-};
-
-static int mbimx51_keymap[] = {
- KEY(0, 0, KEY_1),
- KEY(0, 1, KEY_2),
- KEY(0, 2, KEY_3),
- KEY(0, 3, KEY_UP),
-
- KEY(1, 0, KEY_4),
- KEY(1, 1, KEY_5),
- KEY(1, 2, KEY_6),
- KEY(1, 3, KEY_LEFT),
-
- KEY(2, 0, KEY_7),
- KEY(2, 1, KEY_8),
- KEY(2, 2, KEY_9),
- KEY(2, 3, KEY_RIGHT),
-
- KEY(3, 0, KEY_0),
- KEY(3, 1, KEY_DOWN),
- KEY(3, 2, KEY_ESC),
- KEY(3, 3, KEY_ENTER),
-};
-
-static const struct matrix_keymap_data mbimx51_map_data __initconst = {
- .keymap = mbimx51_keymap,
- .keymap_size = ARRAY_SIZE(mbimx51_keymap),
-};
-
-static int tsc2007_get_pendown_state(void)
-{
- return !gpio_get_value(MBIMX51_TSC2007_GPIO);
-}
-
-struct tsc2007_platform_data tsc2007_data = {
- .model = 2007,
- .x_plate_ohms = 180,
- .get_pendown_state = tsc2007_get_pendown_state,
-};
-
-static struct i2c_board_info mbimx51_i2c_devices[] = {
- {
- I2C_BOARD_INFO("tsc2007", 0x49),
- .irq = IMX_GPIO_TO_IRQ(MBIMX51_TSC2007_GPIO),
- .platform_data = &tsc2007_data,
- }, {
- I2C_BOARD_INFO("tlv320aic23", 0x1a),
- },
-};
-
-/*
- * baseboard initialization.
- */
-void __init eukrea_mbimx51_baseboard_init(void)
-{
- mxc_iomux_v3_setup_multiple_pads(mbimx51_pads,
- ARRAY_SIZE(mbimx51_pads));
-
- imx51_add_imx_uart(1, NULL);
- imx51_add_imx_uart(2, &uart_pdata);
-
- gpio_request(MBIMX51_LED0, "LED0");
- gpio_direction_output(MBIMX51_LED0, 1);
- gpio_free(MBIMX51_LED0);
- gpio_request(MBIMX51_LED1, "LED1");
- gpio_direction_output(MBIMX51_LED1, 1);
- gpio_free(MBIMX51_LED1);
- gpio_request(MBIMX51_LED2, "LED2");
- gpio_direction_output(MBIMX51_LED2, 1);
- gpio_free(MBIMX51_LED2);
- gpio_request(MBIMX51_LED3, "LED3");
- gpio_direction_output(MBIMX51_LED3, 1);
- gpio_free(MBIMX51_LED3);
-
- gpio_led_register_device(-1, &mbimx51_leds_info);
-
- imx51_add_imx_keypad(&mbimx51_map_data);
-
- gpio_request(MBIMX51_TSC2007_GPIO, "tsc2007_irq");
- gpio_direction_input(MBIMX51_TSC2007_GPIO);
- irq_set_irq_type(gpio_to_irq(MBIMX51_TSC2007_GPIO),
- IRQF_TRIGGER_FALLING);
- i2c_register_board_info(1, mbimx51_i2c_devices,
- ARRAY_SIZE(mbimx51_i2c_devices));
-
- imx51_add_sdhci_esdhc_imx(0, NULL);
- imx51_add_sdhci_esdhc_imx(1, NULL);
-}
--
1.7.6.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2011-12-13 07:35    [W:0.120 / U:2.872 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site