lkml.org 
[lkml]   [2011]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 12/21 v2] m68k: drop unused Kconfig symbols
From
Date
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
---
0) Still only "git grep" tested.

1) New in v2:
- redone for linux-next master
- dropped a few "select EMAC_INC" and "select HW_FEITH" lines that
weren't in current mainline
- dropped SOM5282EM too (discovered this while doing this second
version, my scripts aren't smart enough too catch it)

arch/m68k/Kconfig.devices | 28 +------------------------
arch/m68k/Kconfig.machine | 50 ---------------------------------------------
2 files changed, 1 insertions(+), 77 deletions(-)

diff --git a/arch/m68k/Kconfig.devices b/arch/m68k/Kconfig.devices
index d964dc4..dbff941 100644
--- a/arch/m68k/Kconfig.devices
+++ b/arch/m68k/Kconfig.devices
@@ -77,32 +77,6 @@ config MULTIFACE_III_TTY

To compile this driver as a module, choose M here.

-config GVPIOEXT
- tristate "GVP IO-Extender support"
- depends on PARPORT=n && ZORRO
- help
- If you want to use a GVP IO-Extender serial card in Linux, say Y.
- Otherwise, say N.
-
-config GVPIOEXT_LP
- tristate "GVP IO-Extender parallel printer support"
- depends on GVPIOEXT
- help
- Say Y to enable driving a printer from the parallel port on your
- GVP IO-Extender card, N otherwise.
-
-config GVPIOEXT_PLIP
- tristate "GVP IO-Extender PLIP support"
- depends on GVPIOEXT
- help
- Say Y to enable doing IP over the parallel port on your GVP
- IO-Extender card, N otherwise.
-
-config MAC_HID
- bool
- depends on INPUT_ADBHID
- default y
-
config HPDCA
tristate "HP DCA serial support"
depends on DIO && SERIAL_8250
@@ -145,7 +119,7 @@ config DN_SERIAL

config SERIAL_CONSOLE
bool "Support for serial port console"
- depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+ depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
diff --git a/arch/m68k/Kconfig.machine b/arch/m68k/Kconfig.machine
index 7d5c20b..c19b514 100644
--- a/arch/m68k/Kconfig.machine
+++ b/arch/m68k/Kconfig.machine
@@ -303,16 +303,6 @@ config COBRA5282
help
Support for the senTec COBRA5282 board.

-config EMAC_INC
- bool
-
-config SOM5282EM
- bool "EMAC.Inc SOM5282EM board support"
- depends on M528x
- select EMAC_INC
- help
- Support for the EMAC.Inc SOM5282EM module.
-
config WILDFIRE
bool "Intec Automation Inc. WildFire board support"
depends on M528x
@@ -371,27 +361,21 @@ config FIREBEE
help
Support for the FireBee ColdFire 5475 based board.

-config HW_FEITH
- bool
-
config CLEOPATRA
bool "Feith CLEOPATRA board support"
depends on (M5307 || M5407)
- select HW_FEITH
help
Support for the Feith Cleopatra boards.

config CANCam
bool "Feith CANCam board support"
depends on M5272
- select HW_FEITH
help
Support for the Feith CANCam board.

config SCALES
bool "Feith SCALES board support"
depends on M5272
- select HW_FEITH
help
Support for the Feith SCALES board.

@@ -438,13 +422,6 @@ if !MMU || COLDFIRE

comment "Machine Options"

-config ROMFS_FROM_ROM
- bool "ROMFS image not RAM resident"
- depends on (NETtel || SNAPGEAR)
- help
- The ROMfs filesystem will stay resident in the FLASH/ROM, not be
- moved into RAM.
-
config UBOOT
bool "Support for U-Boot command line parameters"
help
@@ -524,33 +501,6 @@ config KERNELBASE
a system with the RAM based at address 0, and leaving enough room
for the theoretical maximum number of 256 vectors.

-choice
- prompt "RAM bus width"
- default RAMAUTOBIT
-
-config RAMAUTOBIT
- bool "AUTO"
- help
- Select the physical RAM data bus size. Not needed on most platforms,
- so you can generally choose AUTO.
-
-config RAM8BIT
- bool "8bit"
- help
- Configure RAM bus to be 8 bits wide.
-
-config RAM16BIT
- bool "16bit"
- help
- Configure RAM bus to be 16 bits wide.
-
-config RAM32BIT
- bool "32bit"
- help
- Configure RAM bus to be 32 bits wide.
-
-endchoice
-
comment "ROM configuration"

config ROM
--
1.7.4.4


\
 
 \ /
  Last update: 2011-10-18 10:13    [W:0.088 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site