lkml.org 
[lkml]   [2011]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: [PATCH 12/21 v2] m68k: drop unused Kconfig symbols
    Hi Paul,

    On 10/18/2011 06:10 PM, Paul Bolle wrote:
    > Signed-off-by: Paul Bolle<pebolle@tiscali.nl>
    > ---
    > 0) Still only "git grep" tested.
    >
    > 1) New in v2:
    > - redone for linux-next master
    > - dropped a few "select EMAC_INC" and "select HW_FEITH" lines that
    > weren't in current mainline
    > - dropped SOM5282EM too (discovered this while doing this second
    > version, my scripts aren't smart enough too catch it)

    Hmm. I don't want to lose the SOM5282EM config option. Although it
    isn't used inside the code it does let the configurer know that this
    specific board is supported.

    Regards
    Greg


    > arch/m68k/Kconfig.devices | 28 +------------------------
    > arch/m68k/Kconfig.machine | 50 ---------------------------------------------
    > 2 files changed, 1 insertions(+), 77 deletions(-)
    >
    > diff --git a/arch/m68k/Kconfig.devices b/arch/m68k/Kconfig.devices
    > index d964dc4..dbff941 100644
    > --- a/arch/m68k/Kconfig.devices
    > +++ b/arch/m68k/Kconfig.devices
    > @@ -77,32 +77,6 @@ config MULTIFACE_III_TTY
    >
    > To compile this driver as a module, choose M here.
    >
    > -config GVPIOEXT
    > - tristate "GVP IO-Extender support"
    > - depends on PARPORT=n&& ZORRO
    > - help
    > - If you want to use a GVP IO-Extender serial card in Linux, say Y.
    > - Otherwise, say N.
    > -
    > -config GVPIOEXT_LP
    > - tristate "GVP IO-Extender parallel printer support"
    > - depends on GVPIOEXT
    > - help
    > - Say Y to enable driving a printer from the parallel port on your
    > - GVP IO-Extender card, N otherwise.
    > -
    > -config GVPIOEXT_PLIP
    > - tristate "GVP IO-Extender PLIP support"
    > - depends on GVPIOEXT
    > - help
    > - Say Y to enable doing IP over the parallel port on your GVP
    > - IO-Extender card, N otherwise.
    > -
    > -config MAC_HID
    > - bool
    > - depends on INPUT_ADBHID
    > - default y
    > -
    > config HPDCA
    > tristate "HP DCA serial support"
    > depends on DIO&& SERIAL_8250
    > @@ -145,7 +119,7 @@ config DN_SERIAL
    >
    > config SERIAL_CONSOLE
    > bool "Support for serial port console"
    > - depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO)&& (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
    > + depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO)&& (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
    > ---help---
    > If you say Y here, it will be possible to use a serial port as the
    > system console (the system console is the device which receives all
    > diff --git a/arch/m68k/Kconfig.machine b/arch/m68k/Kconfig.machine
    > index 7d5c20b..c19b514 100644
    > --- a/arch/m68k/Kconfig.machine
    > +++ b/arch/m68k/Kconfig.machine
    > @@ -303,16 +303,6 @@ config COBRA5282
    > help
    > Support for the senTec COBRA5282 board.
    >
    > -config EMAC_INC
    > - bool
    > -
    > -config SOM5282EM
    > - bool "EMAC.Inc SOM5282EM board support"
    > - depends on M528x
    > - select EMAC_INC
    > - help
    > - Support for the EMAC.Inc SOM5282EM module.
    > -
    > config WILDFIRE
    > bool "Intec Automation Inc. WildFire board support"
    > depends on M528x
    > @@ -371,27 +361,21 @@ config FIREBEE
    > help
    > Support for the FireBee ColdFire 5475 based board.
    >
    > -config HW_FEITH
    > - bool
    > -
    > config CLEOPATRA
    > bool "Feith CLEOPATRA board support"
    > depends on (M5307 || M5407)
    > - select HW_FEITH
    > help
    > Support for the Feith Cleopatra boards.
    >
    > config CANCam
    > bool "Feith CANCam board support"
    > depends on M5272
    > - select HW_FEITH
    > help
    > Support for the Feith CANCam board.
    >
    > config SCALES
    > bool "Feith SCALES board support"
    > depends on M5272
    > - select HW_FEITH
    > help
    > Support for the Feith SCALES board.
    >
    > @@ -438,13 +422,6 @@ if !MMU || COLDFIRE
    >
    > comment "Machine Options"
    >
    > -config ROMFS_FROM_ROM
    > - bool "ROMFS image not RAM resident"
    > - depends on (NETtel || SNAPGEAR)
    > - help
    > - The ROMfs filesystem will stay resident in the FLASH/ROM, not be
    > - moved into RAM.
    > -
    > config UBOOT
    > bool "Support for U-Boot command line parameters"
    > help
    > @@ -524,33 +501,6 @@ config KERNELBASE
    > a system with the RAM based at address 0, and leaving enough room
    > for the theoretical maximum number of 256 vectors.
    >
    > -choice
    > - prompt "RAM bus width"
    > - default RAMAUTOBIT
    > -
    > -config RAMAUTOBIT
    > - bool "AUTO"
    > - help
    > - Select the physical RAM data bus size. Not needed on most platforms,
    > - so you can generally choose AUTO.
    > -
    > -config RAM8BIT
    > - bool "8bit"
    > - help
    > - Configure RAM bus to be 8 bits wide.
    > -
    > -config RAM16BIT
    > - bool "16bit"
    > - help
    > - Configure RAM bus to be 16 bits wide.
    > -
    > -config RAM32BIT
    > - bool "32bit"
    > - help
    > - Configure RAM bus to be 32 bits wide.
    > -
    > -endchoice
    > -
    > comment "ROM configuration"
    >
    > config ROM


    --
    ------------------------------------------------------------------------
    Greg Ungerer -- Principal Engineer EMAIL: gerg@snapgear.com
    SnapGear Group, McAfee PHONE: +61 7 3435 2888
    8 Gardner Close, FAX: +61 7 3891 3630
    Milton, QLD, 4064, Australia WEB: http://www.SnapGear.com


    \
     
     \ /
      Last update: 2011-10-18 14:15    [W:0.039 / U:0.532 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site