lkml.org 
[lkml]   [2011]   [Oct]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 12/21] m68k: drop unused Kconfig symbols
From
Date
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
---
arch/m68k/Kconfig | 28 +---------------------------
arch/m68k/Kconfig.nommu | 44 --------------------------------------------
2 files changed, 1 insertions(+), 71 deletions(-)
diff --git a/arch/m68k/Kconfig b/arch/m68k/Kconfig
index 9e8ee9d..58c6496 100644
--- a/arch/m68k/Kconfig
+++ b/arch/m68k/Kconfig
@@ -149,32 +149,6 @@ config MULTIFACE_III_TTY

To compile this driver as a module, choose M here.

-config GVPIOEXT
- tristate "GVP IO-Extender support"
- depends on PARPORT=n && ZORRO
- help
- If you want to use a GVP IO-Extender serial card in Linux, say Y.
- Otherwise, say N.
-
-config GVPIOEXT_LP
- tristate "GVP IO-Extender parallel printer support"
- depends on GVPIOEXT
- help
- Say Y to enable driving a printer from the parallel port on your
- GVP IO-Extender card, N otherwise.
-
-config GVPIOEXT_PLIP
- tristate "GVP IO-Extender PLIP support"
- depends on GVPIOEXT
- help
- Say Y to enable doing IP over the parallel port on your GVP
- IO-Extender card, N otherwise.
-
-config MAC_HID
- bool
- depends on INPUT_ADBHID
- default y
-
config HPDCA
tristate "HP DCA serial support"
depends on DIO && SERIAL_8250
@@ -217,7 +191,7 @@ config DN_SERIAL

config SERIAL_CONSOLE
bool "Support for serial port console"
- depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+ depends on (AMIGA || ATARI || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || AMIGA_BUILTIN_SERIAL=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all
diff --git a/arch/m68k/Kconfig.nommu b/arch/m68k/Kconfig.nommu
index ff46383..2b7f1e9 100644
--- a/arch/m68k/Kconfig.nommu
+++ b/arch/m68k/Kconfig.nommu
@@ -542,13 +542,6 @@ config SAVANTrosie1
help
Support for the Savant Rosie1 board.

-config ROMFS_FROM_ROM
- bool "ROMFS image not RAM resident"
- depends on (NETtel || SNAPGEAR)
- help
- The ROMfs filesystem will stay resident in the FLASH/ROM, not be
- moved into RAM.
-
config PILOT
bool
default y
@@ -564,21 +557,11 @@ config FREESCALE
default y
depends on (M5206eC3 || M5208EVB || M5235EVB || M5249C3 || M5271EVB || M5272C3 || M5275EVB || M5282EVB || M5307C3 || M5329EVB || M5407C3)

-config HW_FEITH
- bool
- default y
- depends on (CLEOPATRA || CANCam || SCALES)
-
config senTec
bool
default y
depends on (COBRA5272 || COBRA5282)

-config EMAC_INC
- bool
- default y
- depends on (SOM5282EM)
-
config SNEHA
bool
default y
@@ -673,33 +656,6 @@ config KERNELBASE
a system with the RAM based at address 0, and leaving enough room
for the theoretical maximum number of 256 vectors.

-choice
- prompt "RAM bus width"
- default RAMAUTOBIT
-
-config RAMAUTOBIT
- bool "AUTO"
- help
- Select the physical RAM data bus size. Not needed on most platforms,
- so you can generally choose AUTO.
-
-config RAM8BIT
- bool "8bit"
- help
- Configure RAM bus to be 8 bits wide.
-
-config RAM16BIT
- bool "16bit"
- help
- Configure RAM bus to be 16 bits wide.
-
-config RAM32BIT
- bool "32bit"
- help
- Configure RAM bus to be 32 bits wide.
-
-endchoice
-
comment "ROM configuration"

config ROM
--
1.7.4.4





\
 
 \ /
  Last update: 2011-10-14 14:33    [from the cache]
©2003-2011 Jasper Spaans