lkml.org 
[lkml]   [2011]   [Oct]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 5/5] tty/serial: atmel_serial: add device tree support
On Wed, Oct 12, 2011 at 06:07:00PM +0200, Nicolas Ferre wrote:
> Will use aliases to enumerate ports, if available.
>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Acked-by: Grant Likely <grant.likely@secretlab.ca>

> ---
> drivers/tty/serial/atmel_serial.c | 79 +++++++++++++++++++++++++++++++++----
> 1 files changed, 71 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 1074329..fc4081e 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -33,6 +33,8 @@
> #include <linux/sysrq.h>
> #include <linux/tty_flip.h>
> #include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> #include <linux/dma-mapping.h>
> #include <linux/atmel_pdc.h>
> #include <linux/atmel_serial.h>
> @@ -163,6 +165,16 @@ static unsigned long atmel_ports_in_use;
> static struct console atmel_console;
> #endif
>
> +#if defined(CONFIG_OF)
> +static const struct of_device_id atmel_serial_dt_ids[] = {
> + { .compatible = "atmel,at91rm9200-usart" },
> + { .compatible = "atmel,at91sam9260-usart" },
> + { /* sentinel */ }
> +};
> +
> +MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids);
> +#endif
> +
> static inline struct atmel_uart_port *
> to_atmel_uart_port(struct uart_port *uart)
> {
> @@ -1411,6 +1423,48 @@ static struct uart_ops atmel_pops = {
> #endif
> };
>
> +static void __devinit atmel_of_init_port(struct atmel_uart_port *atmel_port,
> + struct device_node *np)
> +{
> + u32 rs485_delay[2];
> +
> + /* DMA/PDC usage specification */
> + if (of_get_property(np, "atmel,use-dma-rx", NULL))
> + atmel_port->use_dma_rx = 1;
> + else
> + atmel_port->use_dma_rx = 0;
> + if (of_get_property(np, "atmel,use-dma-tx", NULL))
> + atmel_port->use_dma_tx = 1;
> + else
> + atmel_port->use_dma_tx = 0;
> +
> + /* rs485 properties */
> + if (of_property_read_u32_array(np, "rs485-rts-delay",
> + rs485_delay, 2) == 0) {
> + struct serial_rs485 *rs485conf = &atmel_port->rs485;
> +
> + rs485conf->delay_rts_before_send = rs485_delay[0];
> + rs485conf->delay_rts_after_send = rs485_delay[1];
> + rs485conf->flags = 0;
> +
> + if (rs485conf->delay_rts_before_send == 0 &&
> + rs485conf->delay_rts_after_send == 0) {
> + rs485conf->flags |= SER_RS485_RTS_ON_SEND;
> + } else {
> + if (rs485conf->delay_rts_before_send)
> + rs485conf->flags |= SER_RS485_RTS_BEFORE_SEND;
> + if (rs485conf->delay_rts_after_send)
> + rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
> + }
> +
> + if (of_get_property(np, "rs485-rx-during-tx", NULL))
> + rs485conf->flags |= SER_RS485_RX_DURING_TX;
> +
> + if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
> + rs485conf->flags |= SER_RS485_ENABLED;
> + }
> +}
> +
> /*
> * Configure the port from the platform device resource info.
> */
> @@ -1420,6 +1474,14 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
> struct uart_port *port = &atmel_port->uart;
> struct atmel_uart_data *pdata = pdev->dev.platform_data;
>
> + if (pdev->dev.of_node) {
> + atmel_of_init_port(atmel_port, pdev->dev.of_node);
> + } else {
> + atmel_port->use_dma_rx = pdata->use_dma_rx;
> + atmel_port->use_dma_tx = pdata->use_dma_tx;
> + atmel_port->rs485 = pdata->rs485;
> + }
> +
> port->iotype = UPIO_MEM;
> port->flags = UPF_BOOT_AUTOCONF;
> port->ops = &atmel_pops;
> @@ -1433,7 +1495,7 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
>
> memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
>
> - if (pdata->regs) {
> + if (pdata && pdata->regs) {
> /* Already mapped by setup code */
> port->membase = pdata->regs;
> } else {
> @@ -1450,10 +1512,6 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
> /* only enable clock when USART is in use */
> }
>
> - atmel_port->use_dma_rx = pdata->use_dma_rx;
> - atmel_port->use_dma_tx = pdata->use_dma_tx;
> - atmel_port->rs485 = pdata->rs485;
> -
> /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
> if (atmel_port->rs485.flags & SER_RS485_ENABLED)
> atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
> @@ -1718,17 +1776,21 @@ static int atmel_serial_resume(struct platform_device *pdev)
> static int __devinit atmel_serial_probe(struct platform_device *pdev)
> {
> struct atmel_uart_port *port;
> + struct device_node *np = pdev->dev.of_node;
> struct atmel_uart_data *pdata = pdev->dev.platform_data;
> void *data;
> int ret = -ENODEV;
>
> BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
>
> - if (pdata)
> - ret = pdata->num;
> + if (np)
> + ret = of_alias_get_id(np, "serial");
> + else
> + if (pdata)
> + ret = pdata->num;
>
> if (ret < 0)
> - /* port id not found in platform data:
> + /* port id not found in platform data nor device-tree aliases:
> * auto-enumerate it */
> ret = find_first_zero_bit(&atmel_ports_in_use,
> sizeof(atmel_ports_in_use));
> @@ -1827,6 +1889,7 @@ static struct platform_driver atmel_serial_driver = {
> .driver = {
> .name = "atmel_usart",
> .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(atmel_serial_dt_ids),
> },
> };
>
> --
> 1.7.5.4
>


\
 
 \ /
  Last update: 2011-10-13 04:29    [W:0.065 / U:0.800 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site