lkml.org 
[lkml]   [2011]   [Jan]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V2] ST SPEAr: PCIE gadget suppport
On Thu, Jan 06, 2011 at 05:29:10PM +0530, Viresh Kumar wrote:
> From: Pratyush Anand <pratyush.anand@st.com>
>
> This is a configurable gadget. can be configured by sysfs interface. Any
> IP available at PCIE bus can be programmed to be used by host
> controller.It supoorts both INTX and MSI.
> By default, gadget is configured for INTX and SYSRAM1 is mapped to BAR0
> with size 0x1000
>
> Changes since V1:
> - __iomem added for register addresses
> - kerneldoc comment removed whereever not required.
> - help node moved from sysfs to documentation/misc-devices
> - strict_strtoul used instead of sscanf
>
> Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
> ---
> Documentation/misc-devices/spear-pcie-gadget.txt | 125 ++++

New sysfs entries require updates to the Documentation/ABI/ directory
for them.

Please rework the patch to include these entries.

> +read behaviour of nodes:
> +------------------------------
> +link :gives ltssm status.
> +int_type :type of supported interrupt
> +no_of_msi read :zero if MSI is not enabled by host.A positive value is the
> + number of MSI vector granted.
> +vendor_id :returns programmed vendor id (hex)
> +device_id :returns programmed device id(hex)
> +bar0_size: :retruns size of bar0 in hex.
> +bar0_address :returns address of bar0 mapped area in hex.
> +bar0_rw_offset :returns offset of bar0 for which bar0_data will return value.
> +bar0_data :returns data at bar0_rw_offset.
> +
> +write behaviour of nodes:
> +------------------------------
> +link :write UP to enable ltsmm DOWN to disable
> +int_type :write interrupt type to be configured and (int_type could be
> + INTA, MSI or NO_INT).select MSI only when you have programmed
> + no_of_msi node.
> +no_of_msi :number of MSI vector needed.
> +inta :write 1 to assert INTA and 0 to de-assert.
> +send_msi :write MSI vector to be send.
> +vendor_id :write vendor id(hex) to be programmed.
> +device_id :write device id(hex) to be programmed.
> +bar0_size :write size of bar0 in hex. default bar0 size is 1000 (hex)
> + bytes.
> +bar0_address :write address of bar0 mapped area in hex. (default mapping of
> + bar0 is SYSRAM1(E0800000).Aalways program bar size before bar
> + address. kernel might modify bar size and address to align. So
> + read back bar size and address after writing to cross check.
> +bar0_rw_offset :write offset of bar0 for which bar0_data will write value.
> +bar0_data :write data to be written at bar0_rw_offset.

Should you use configfs for this instead of sysfs? It looks like that
is what you are looking for here.

thanks,

greg k-h


\
 
 \ /
  Last update: 2011-01-06 19:55    [W:0.678 / U:0.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site